Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for KitchenAid KSM150WPCU0
Summary of Contents for KitchenAid KSM150WPCU0
- Page 1 K45 Series KSM45–KSM200 Series...
-
Page 2: Parts And Features
PARTS AND FEATURES Motor Head (locking lever not shown) Bowl** Attachment Knob Beater Shaft Attachment Hub Pouring shield* Motor Head 3 L Stainless Steel Bowl* Speed Control Lever Flat Beater Beater Height Adjustment screw Flex Edge Beater* (not shown) Wire Whip Bowl Clamping Plate Dough Hook *Included with select models only. -
Page 3: Product Safety
PRODUCT SAFETY IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed, including the following: 1. Read all instructions. 2. To protect against risk of electrical shock, do not put Stand Mixer in water or other liquid. 3. -
Page 4: Getting Started
PRODUCT SAFETY 9. Do not let the cord hang over the edge of table or counter. 10. Remove the beaters, wire whip, or dough hook from the Stand Mixer before washing. SAVE THESE INSTRUCTIONS This product is designed for household use only. ELECTRICAL REQUIREMENTS Voltage: 120 V Frequency: 60 Hz... -
Page 5: Speed Control Guide
SPEED CONTROL GUIDE Note : The speed control can be set to obtain speeds 1, 3, 5, 7, and 9 if a finer adjustment is required. Do not exceed Speed 2 when preparing yeast doughs as this may cause damage to the Stand Mixer. - Page 6 PRODUCT ASSEMBLY Place the bowl on the clamping plate Slide and rotate the accessory aligning and twist to lock in place. over the pin on the shaft. Unlock the motor head and move it down. Then, lock the head to keep it down.
-
Page 7: Product Usage
PRODUCT USAGE Plug it into a grounded 3 prong outlet. Start with lower speed to avoid splashing and increase it gradually. Refer to the “Speed Control guide”. Do not scrape the bowl while operating. Scraping the bowl once or twice during mixing is usually sufficient. -
Page 8: Disassembling The Product
OPTIONAL ATTACHMENTS KitchenAid ® offers a wide range of optional attachments such as the Spiralizer, Pasta Cutters, or Food Grinder that may be attached to the Stand Mixer attachment power hub as shown here. -
Page 9: Care And Cleaning
OPTIONAL ATTACHMENTS Insert attachment into attachment hub, Tighten the attachment knob by turning it making certain that attachment power clockwise until the attachment is secured shaft fits into the square attachment hub to the Stand Mixer. socket. CARE AND CLEANING IMPORTANT: Do not immerse the Stand Mixer body in water or other liquids. -
Page 10: Troubleshooting Guide
TROUBLESHOOTING GUIDE WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. -
Page 11: Warranty And Service
IF THIS PRODUCT FAILS TO WORK AS WARRANTED, CUSTOMER’S SOLE AND EXCLUSIVE REMEDY SHALL BE REPAIR OR REPLACEMENT ACCORDING TO THE TERMS OF THIS LIMITED WARRANTY. KITCHENAID AND KITCHENAID CANADA DO NOT ASSUME ANY RESPONSIBILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty gives you specific legal rights and you may also have other... - Page 12 P.O. Box 218, St. Joseph, MI 49085-0218 For service information in Mexico: Call toll-free 01-800-0022-767. ®/™ ©2019 KitchenAid. All rights reserved. KITCHENAID and the design of the stand mixer are trademarks in the U.S. and elsewhere. Used under license in Canada.
- Page 13 ®/™ ©2019 KitchenAid. All rights reserved. KITCHENAID and the design of the stand mixer are trademarks in the U.S. and elsewhere. Used under license in Canada. Tous droits réservés. KitchenAid et la forme du batteur sur socle sont des marques de commerce aux É.-U. et ailleurs. Utilisé sous licence au Canada.