Table of Contents
Advertisement
Quick Links
BSX8000-5 Broadband Services Switch
Installation Instructions
Document Number BSX8-A2-GZ40-20
June 2005
Contents
Software and Firmware License Agreement
The terms and conditions of this License Agreement (the "Agreement") will apply to the
software and/or firmware (individually or collectively the "Software") incorporated into the
Paradyne product (the "Product") purchased by you and any derivatives obtained from the
BSX8-A2-GZ40-20
................................................................................................... 3
........................................................................................ 3
.............................................................................................. 6
......................................................................................... 6
................................................................................................... 13
ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS TERMS,
YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED INTO THE
PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU SHOW YOUR
ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.
June 2005
...................................................... 1
.......................................................................... 3
......................................................... 4
.................................................................... 5
....................................................................... 5
.......................................................................... 10
......................................................................... 14
............................................................................ 14
................................................. 15
........................................... 15
............................ 4
1
Advertisement
Table of Contents
Summary of Contents for Zhone BSX8000
-
Page 1: Table Of Contents
Software and Firmware License Agreement Product Documentation Online Release Notes BSX8000-5 Overview Unpacking and Inspecting the Equipment Installing a Micro Interface Module (MIM) in the BSX8000-5 Installing the BSX8000-5 in a BLC Connect the MIM to the Network BLC Management Web Interface (NMS) - Page 2 Software, including any copy of either. If you have executed a separate written agreement covering the Software supplied to you under this purchase, such separate written agreement shall govern. Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to accept a personal, non-transferable, non-exclusive, right (without the right to sublicense) to use the Software, solely as it is intended and solely as incorporated in the Product purchased from Paradyne or its authorized distributor or reseller under the following terms and conditions:...
-
Page 3: Product Documentation Online
4000E and 12000E Broadband Loop Carriers (BLCs). The BSX8000-5 supports four fixed 10/100/1000 RJ45 Ethernet interfaces and one MIM (Micro Interface Module) slot. Multiple MIM varieties are supported. The BSX8000-5 delivers a full 1 Gbps full duplex backplane connection to each access module in the BLC. -
Page 4: Unpacking And Inspecting The Equipment
CAUTION: Cover plates should be stored for possible future use. If a MIM is removed from a BSX8000-5, it must be replaced with either another MIM or a cover plate. Do not operate a BSX8000-5 with an open MIM port. -
Page 5: Installing The Bsx8000-5 In A Blc
(such as the AIM24000-48) and slots U1 and U2 are reserved for uplink modules. Although not required for operational purposes, if redundancy is desired, two BSX8000-5 modules may be installed in the 12000E, in slots U1 and U2. (Note: For redundancy, the two uplink modules in the chassis must be identical models.) -
Page 6: Blc Management
Verify the connection: the Lnk (link) LED on the MIM faceplate flashes green to indicate a network connection has been established. BLC Management The BSX8000-5 uplink module provides BLC management capability via the Command Line Interface (CLI), Simple Network Management Protocol (SNMP), and the web-based Network Management System (NMS). - Page 7 9. Start your web browser. Type the default IP address into the Address field and press Enter. The default IP address of a BSX8000-5 in Slot 13 of a 12000E BLC or Slot 5 of a 4000E BLC is 192.168.254.252. The default IP address of a BSX8000-5 in Slot 14 of a 12000E BLC is 192.168.254.253.
- Page 8 The NMS home page appears. June 2005 BSX8-A2-GZ40-20...
- Page 9 NMS Management Configuration Use the Management Configuration screen to set the unit’s IP address and other management parameters. Procedure To configure management parameters: 1. From the home screen, click on the Management Config button. The Management Configuration screen appears. 2. Select or enter the following parameters: Parameter IP Address Subnet Mask...
-
Page 10: Command Line Interface (Cli)
Parameter Flood Configuration Flood Membership Configuration 3. Click on Submit. Command Line Interface (CLI) CLI System Requirements Straight-Through RJ45 to RJ45 Ethernet Cable – Required for establishing a direct connection from the COM port to a DB9 adapter. DB9 Female to RJ45 Male Adapter – Required for conversion of your PC's RS232 serial port for use with the RJ45 to RJ45 Ethernet cable. -
Page 11: Logging Into The Cli
2. Connect one end of a straight-through RJ45 to RJ45 Ethernet cable into the adapter plugged into your PC, and the other end of the cable into the COM port on the face of the BSX8000-5. Launching the Terminal Emulation Program Launch the terminal emulation program on your PC and configure the program settings. - Page 12 Table 1. CLI Commands (2 of 2) Command CLEAR_NVRAM DISABLE_TELNET DISABLE_TFTP DISABLE_WEB_SERVER] ENABLE_TELNET ENABLE_TFTP ENABLE_WEB_SERVER HELP LOGOUT SHOW Description If no interface modules are present in the chassis, clears Non-Volatile Random Access Memory, restoring the DSLAM to factory defaults. Disables access to the DSLAM using Telnet. Disables access to the DSLAM using Trivial File Transfer Protocol.
-
Page 13: Led Indicators
Both BLC power terminals are connected. Only one of the BLC power terminals is connected. The BSX8000-5 uplink module is not receiving power (the BLC may or may not be receiving power). All four of the fans on the BLC fan card are functioning. -
Page 14: 10/100/1000Baset Connectors
10/100/1000BaseT Connectors The uplink ports are 8-pin unkeyed modular jacks for a 10/100/1000BaseT interface. The MGMT port is an 8-pin modular jack supporting 10/100BaseT. Table 3. 10/100/1000 Pinouts Signal Transmitted Data + Transmitted Data – Received Data + Unused Unused Received Data –... -
Page 15: Regulatory Compliance For Class A Equipment
Regulatory Compliance for Class A Equipment The following regulatory compliance information applies to a BSX8000-5 as installed in a Paradyne BLC. US Federal Communications Commission (FCC) NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 16 *BSX8-A2-GZ40-20* *BSX8-A2-GZ40-20* June 2005 BSX8-A2-GZ40-20...