Page 1  Hotwire TDM SHDSL Endpoints Models 7995-A2-411, 7995-A2-421, 7995-A2-422, 7995-A2-700, 7996-A2-410, 7996-A2-420, and 7996-A2-700 User’s Guide Document No. 7990-A2-GB20-20 September 2004...
Page 2 Copyright © 2004 Paradyne Corporation. All rights reserved. Printed in U.S.A. Notice This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language in any form or by any means, electronic, mechanical, magnetic, manual or otherwise, or disclosed to third parties without the express written permission of Paradyne Corporation, 8545 126th Ave.
Page 3: Table Of Contents
Contents About This Guide „ Document Purpose and Intended Audience ....„ Document Summary ........„...
Page 4 Contents „ Connecting to a DTE ........„...
Page 5 „ Viewing DSL Error Statistics ....... . „ Viewing DSL Performance Statistics ......„...
Page 6 Contents SNMP NMS Security Options ......SNMP Traps Options........B Standards Compliance for SNMP Traps „...
Page 7: About This Guide
About This Guide Document Purpose and Intended Audience This guide contains information needed to set up, configure, and operate the Hotwire Time Division Multiplexer Symmetric High-bit-rate Digital Subscriber Line (TDM SHDSL) endpoints, Models 7995-A2-411, 7995-A2-421, 7995-A2-422, 7995-A2-700, 7996-A2-410, 7996-A2-420, and 7996-A2-700, and is intended for installers and operators.
Page 8: Product-Related Documents
Contents Section Appendix C, Connectors, Cables, and Pin Assignments Appendix D, Technical Specifications Index A master glossary of terms and acronyms used in Paradyne documents is available online at www.paradyne.com. Select Support → Technical Manuals→ Technical Product-Related Documents Complete documentation for this product is available online at www.paradyne.com.
Page 9: About The Tdm Shdsl Endpoint
About the TDM SHDSL Endpoint TDM SHDSL Overview ® Hotwire Time Division Multiplexer Symmetric High-bit-rate Digital Subscriber Line (TDM SHDSL) products maximize customer service areas by varying the DSL line rate. This ensures symmetric DSL connectivity over a wide range of telephone line distances and transmission line qualities.
Page 10: Tdm Shdsl Endpoint Features
1. About the TDM SHDSL Endpoint TDM SHDSL Endpoint Features Hotwire TDM SHDSL Models 7995-A2-411, 7995-A2-421, 7995-A2-422, 7995-A2-700, 7996-A2-410, 7996-A2-420, and 7996-A2-700 are endpoints for the chassis-mounted Hotwire 8799 Line Card that is housed in the Hotwire 8600 or 8800 Series Digital Subscriber Line Access Multiplexer (DSLAM). Two Hotwire TDM SHDSL endpoints can also be configured to operate in a central office SHDSL Transceiver Unit, Central Site (STU-C)-to-customer premises SHDSL Transceiver Unit, Remote Terminal Site (STU-R) environment.
Page 11: Network Configuration
Network Configuration Figure 1-1, Sample in a central office (CO). In this configuration, a frame relay switch and router are connected through the endpoint to partner units supporting a host or router and frame relay encapsulated or unframed data. The figure also shows a standalone-to-standalone configuration.
Page 12: Front Panel Led Status Indicators
Figure 1-3. Figure 1-3 show the front panels of the Hotwire TDM SHDSL 7995 TDM SHDSL ® Hotwire 7995 TDM SHDSL Endpoint with Synchronous Interface Front Panel 7996 TDM SHDSL Hotwire 7996 TDM SHDSL Endpoint with G.703 Interface Front Panel...
Page 13: Rear Panel Interfaces
Figure 1-5. 7990-A2-GB20-20 Figure 1-5 show the physical interfaces of the endpoints. For more Assignments. PORT Hotwire 7995 TDM SHDSL Endpoint with Synchronous Interface Rear Panel 120Ω Hotwire 7996 TDM SHDSL Endpoint with G.703 Interface Rear Panel September 2004 1. About the TDM SHDSL Endpoint...
Page 14: Snmp Management Capabilities
1. About the TDM SHDSL Endpoint SNMP Management Capabilities Hotwire Model 7995/7996 endpoints support SNMP Version 1, and can be managed by any industry-standard SNMP manager and accessed by external SNMP managers using SNMP. Management Information Base (MIB) Support For a detailed description of the supported MIBs, visit Paradyne’s Web site at www.paradyne.com.
Page 15: Snmp Trap Support
The Hotwire Model 7995/7996 Endpoint supports traps as defined in RFC 1215. Figure 1-6, DSL SNMP configuration. configuration where the NMS is connected directly to the endpoint’s Communications Port. example of an IP addressing scheme. Router Figure 1-6. Router Figure 1-7. Router Figure 1-8.
Page 16 1. About the TDM SHDSL Endpoint September 2004 7990-A2-GB20-20...
Page 17: Using The Asynchronous Terminal Interface
Using the Asynchronous Terminal Interface User Interface Access You can communicate with the Hotwire TDM SHDSL endpoint with an asynchronous terminal interface (ATI) using one of the following methods: „ Direct connection through the COM port of the endpoint or through the serial port of the DSLAM management card.
Page 18: Initiating An Ati Session
2. Using the Asynchronous Terminal Interface Initiating an ATI Session The Main Menu screen is displayed unless a login ID and password is required or the ATI is already in use. If the ATI is already in use, you will see: „...
Page 19 After you enter a valid login ID and password, the Main Menu appears. If you enter an invalid login ID and password after three attempts, the Telnet session closes or the terminal connection returns to an idle state. Refer to main Screen Area...
Page 20: Menu Hierarchy
2. Using the Asynchronous Terminal Interface Menu Hierarchy The following illustration shows the menu paths to the different ATI screens. System and Test Status Error Statistics Performance Statistics 7995: DSL Tests 7996: DSL and G.703 Tests DSL Port Main Status Test Configuration Performance...
Page 21: Screen Work Areas
Screen Work Areas There are two user work areas: „ Screen area – This is the area above the dotted line that provides the menu path, menus, and input fields. The menu path appears as the first line on the screen. In this manual, the menu path is presented as a menu selection sequence: Main Menu→Configuration→...
Page 22: Navigating The Screens
2. Using the Asynchronous Terminal Interface Navigating the Screens You can navigate the screens by: „ Using keyboard keys „ Using function keys „ Switching between the two screen work areas Keyboard Keys Use the following keyboard keys to navigate within the screen. Press .
Page 23: Function Keys
Procedure To make a menu or field selection: 1. Press the Tab key or the right arrow key to position the cursor on a menu or field selection. Each selection is highlighted as you press the key to move the cursor from position to position.
Page 24: Switching Between Screen Work Areas
2. Using the Asynchronous Terminal Interface Switching Between Screen Work Areas Select Ctrl-a to switch between the two screen work areas to perform all screen functions. Procedure To access the screen function area below the dotted line: 1. Press Ctrl-a to switch from the screen area to the function key and message area below the dotted line.
Page 25: Initial Startup And Configuration
Initial Startup and Configuration Overview This chapter provides instructions on how to access and configure your Hotwire TDM SHDSL endpoint for the first time, displaying configuration options, using the Adaptive Rate feature, and downloading firmware. These procedures include: „ Connecting Power „...
Page 26: Connecting Power
3. Initial Startup and Configuration Connecting Power If your package includes a power pack: Plug the power pack into an AC outlet having a nominal voltage rating between 100 – 240 VAC. Connect the output cable of the power pack to the connector marked POWER on the rear panel. If your package includes a direct-connection DC power cable: Connect the unit to an external +24 or –48 VDC power source as described in an Optional External DC Power...
Page 27: Connecting To The Network
Table 3-1. Pin Number Connecting to the Network Procedure To connect the unit to the network: 1. Plug one end of the network cable into the rear panel DSL jack. 2. Connect the other end to the DSL network interface. NOTE: Do not use a flat VF network cable as this may severely degrade the performance of the unit.
Page 28: Connecting To A System Terminal
3. Initial Startup and Configuration Connecting to a System Terminal An optional system maintenance terminal may be attached to the standalone endpoint through the modular jack on the rear panel. The terminal allows you to view the status of the unit and change configuration options. It must be a VT100-compatible terminal or a PC running terminal emulation software.
Page 29: Entering Identity Information
Entering Identity Information After accessing the unit for the first time, use the Change Identity screen to determine SNMP administrative system information that will be displayed on the Identity screen of the Status branch. To access the Identity screen, follow this menu selection sequence: Main Menu→Control→Change Identity main/control/change_identity...
Page 30: Choosing A Configuration Method
3. Initial Startup and Configuration Procedure To change Identity information: 1. Position the cursor in the System Name field. Enter a name unique in your network to identify the SNMP managed node (or unit). 2. Position the cursor in the System Location field. Enter the physical location of the unit.
Page 31: Configuring The Unit Using Configuration Menus
Use the Configuration menus to select, display, or change configuration option settings. NOTE: The Hotwire 7995/7996 TDM SHDSL Endpoint is preconfigured as an STU-R. If using the unit as an STU-R, you may not need to change any configuration option settings.
Page 32: Accessing And Displaying Configuration Options
3. Initial Startup and Configuration Accessing and Displaying Configuration Options To display configuration options, you must first load a configuration into the edit area. To load a configuration option set into the configuration edit area, follow this menu selection sequence: Main Menu→Configuration (Load Configuration From) main/configuration --------------------------------------------------------------------------------...
Page 33: Current And Default Factory Configurations
Current and Default Factory Configurations The Configuration Edit/Display screen appears when the current or default configuration is loaded. To access the Configuration Edit/Display screen, follow this menu selection sequence: Main Menu→Configuration →Current Configuration – or – Main Menu→Configuration →Default Factory Configuration main/config/edit -------------------------------------------------------------------------------- Ctrl-a to access these functions, ESC for previous menu...
Page 34 3. Initial Startup and Configuration Appendix A, Configuration configuration options. Select . . . DSL Port DSL Threshold Traps SYNC Port G.703 System Options Communication Port Management and Communication 3-10 Options, for a list and explanation of the To Access the . . . DSL Interface Options (Table A-1)
Page 35: Configuration Loader
Configuration Loader The Configuration Loader screen allows you to upload configurations to and download configurations from a TFTP server. To access the Configuration Loader screen, follow this menu selection sequence: Main Menu→Configuration →Configuration Loader main/configuration/config_loader Configuration File Name: TFTP Server IP Address: TFTP Transfer Direction: ------------------------------------------------------------------------------- Ctrl-a to access these functions, ESC for previous menu...
Page 36 3. Initial Startup and Configuration 2. Position the cursor in the TFTP Server IP Address field. Enter the TFTP server IP address or the MCP IP address for the MCP FFS. The first three digits of the IP address cannot be 000 or greater than 223. For an MCP FFS, you must include the directory names separated by a forward slash.
Page 37: Saving Configuration Options
Saving Configuration Options When changes are made to the configuration options through the Configuration Edit/Display branch, the changes must be saved to take effect. Use the Save key or Save Configuration screen. Procedure To save configuration options changes: 1. Press Ctrl-a to switch to the function key and message area. 2.
Page 38: Resetting The Device
3. Initial Startup and Configuration Resetting the Device If the user interface is functional, you can perform a power-on reset of the unit from the Control menu. Procedure To reset the unit from the Control menu: 1. Follow this menu selection sequence: Main Menu→Control→Reset Device 2.
Page 39: Adaptive Rate Feature
Adaptive Rate Feature The Adaptive Rate feature is designed to find the best rate possible for your DSL loop conditions. After the DSL loop is up, configure the unit for a fixed rate by setting the minimum DSL rate equal to the maximum DSL rate. The configuration options are available from the DSL Interface Options screen.
Page 40: Downloading Firmware
3. Initial Startup and Configuration Downloading Firmware The Download Code screen allows you to download firmware from a TFTP server. To access the Download Code screen, follow this menu selection sequence: Main Menu→Control →Download Code main/control/download_code TFTP Server IP Address: TFTP Server Destination: Immediately Apply Download: -------------------------------------------------------------------------------...
Page 41 5. Position the cursor at the Start Transfer field. Use the spacebar to select Yes. Press Enter. When the data transfer is complete: — If you selected Yes in Step 4, the unit is reset. — If you selected No in Step 4, the Transfer Status field changes to Completed successfully.
Page 42 3. Initial Startup and Configuration 3-18 September 2004 7990-A2-GB20-20...
Page 43: Configuring The Unit Using The Internal Switches
Configuring the Unit Using the Internal Switches Overview You can make configuration changes through a VT100-compatible terminal and the unit’s Configuration menus or by manually changing switches on the board. The unit is shipped with the switchpack disabled to allow settings to be made through the Configuration menus.
Page 44: Configuring The Unit Using Internal Switches
4. Configuring the Unit Using the Internal Switches Configuring the Unit Using Internal Switches Use internal Switchpack S3 to manually configure the unit. HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to electrostatic discharge (ESD) during normal operation. When performing installation procedures, however, take proper static control precautions to prevent damage to equipment.
Page 45: Switchpack Location
Switchpack Location To locate Switchpack S3, refer to Switchpack Switchpack Figure 4-1. 7990-A2-GB20-20 4. Configuring the Unit Using the Internal Switches Figure 4-1, Hotwire TDM SHDSL Endpoint Location. Rear Front Hotwire TDM SHDSL Endpoint Switchpack Location September 2004 03-17364...
Page 46: Model 7995 Switchpack Definitions
4. Configuring the Unit Using the Internal Switches Model 7995 Switchpack Definitions Table 4-1, Switchpack S3 Definitions – Model 7995 configuring the Model 7995 endpoint. Table 4-1. Switch # . . . 3, 4, 5 7, 8 Switchpack S3 Definitions – Model 7995 Allows you to .
Page 47: Model 7996 Switchpack Definitions
Model 7996 Switchpack Definitions Table 4-2, Switchpack S3 Definitions – Model 7996 configuring the Model 7996 endpoint. Table 4-2. Switch # . . . 3, 4, 5 7990-A2-GB20-20 4. Configuring the Unit Using the Internal Switches Switchpack S3 Definitions – Model 7996 Allows you to .
Page 48 4. Configuring the Unit Using the Internal Switches September 2004 7990-A2-GB20-20...
Page 49: Security
Security Overview Security on the Hotwire TDM SHDSL endpoint is implemented by limiting user access to the ATI through option settings. You can: „ Enable the Telnet Login Required option. „ Enable the COM port Login Required option. „ Limit access by setting a Session Access Level option of Operator for the Telnet session.
Page 50: Ati Access Levels
5. Security ATI Access Levels The unit has two access levels: Administrator and Operator. The access level determines what functions are accessible, as shown in Table 5-1. ATI Access to Menu Functions Status Test Configuration Control Access levels can be applied to Login IDs, the COM port, and Telnet sessions. The effective access level is always the most restrictive: „...
Page 51: Creating A Login
Creating a Login Logins apply to the terminal directory connected to the communication port or Telnet access directly to the ATI of the unit. Six login ID/password combinations are available. Each Login ID and Password must be unique and include an access level. Procedure 1.
Page 52: Deleting A Login
5. Security 3. Create the login by entering the following fields. Login IDs and passwords are case-sensitive. On the Login Entry screen, for the . . . Login ID Password Re-enter Password Access Level NOTE: Assign at least one Administrator-level Login ID. Full access is necessary to make configuration option changes and administer logins.
Page 53: Resetting The Unit's Com Port Or Factory Defaults
Resetting the Unit’s COM Port or Factory Defaults The user interface can be rendered inaccessible with a faulty configuration. Two methods can be used to restore it: „ Reset COM Port – Allows you to reset the configuration options related to COM port usage.
Page 54: Controlling Snmp Access
5. Security Controlling SNMP Access There are three methods for limiting SNMP access: „ Disable the SNMP management option. Refer to Management Options, „ Assign SNMP community names and access types. „ Limit SNMP access through validation of the IP address of each allowed SNMP manager.
Page 55: Monitoring And Troubleshooting
Monitoring and Troubleshooting What to Monitor This chapter presents information on how to access and monitor Hotwire TDM SHDSL endpoints. You can monitor a unit’s operations by referencing the following sections: „ Viewing System and Test Status — Health and Status Messages —...
Page 56: Viewing System And Test Status
6. Monitoring and Troubleshooting Viewing System and Test Status To view System and Test Status information, follow this menu selection sequence: Main Menu→Status→System and Test Status main/status/system HEALTH AND STATUS System Operational -------------------------------------------------------------------------------- PgUp The System and Test Status screen has three sections: „...
Page 57: Health And Status Messages
Health and Status Messages The messages in column of the System and Test Status screen. The highest priority Health and Status message also appears on all ATI screens on the bottom right. Table 6-1. Message AIS at G.703 DeviceFailed yyyyyyyy Download Failed DSL Attenuation Threshold...
Page 58 6. Monitoring and Troubleshooting Table 6-1. Message EER at G.703 LOF at G.703 LOS at G.703 LOS at DSL Net Com Link Down Primary Clock Failed RAI (Remote Alarm Indication) at G.703 Health and Status Messages (2 of 3) What Message Indicates An EER (Excessive Error Rate) condition has been detected on the G.703...
Page 59 Table 6-1. Message Remote Unit Power Off The remote unit has lost STU-R TS16 Not Supported System Operational 7990-A2-GB20-20 Health and Status Messages (3 of 3) What Message Indicates power (last gasp). The STU-C is configured for TS16 signaling (Voice mode) and the STU-R is not configured to support TS16 signaling.
Page 60: Self-Test Results Messages
6. Monitoring and Troubleshooting Self-Test Results Messages Table 6-2, Self-Test Results reset self-test that appear in the middle column of the System and Test Status screen. Table 6-2. Message CPU Failed DataPath Failed Device Failed Failure xxxxxxxx G.703 Failed Memory Failed Passed Messages, lists the results of the last power-up or Self-Test Results Messages...
Page 61: Test Status Messages
Test Status Messages The Test Status messages in column of the System and Test Status screen. Table 6-3. Test Status Message 511 Test Active DCLB Test Active DLB Test Active DTLB Test Active Lamp Test Active LLB Test Active No Test Active Remote DCLB Dn Active A Remote Data Channel Loopback Down command is being Remote DCLB Up Active A Remote Data Channel Loopback Up command is being sent.
Page 62: Entry Response Messages
6. Monitoring and Troubleshooting Entry Response Messages The messages in to commands or during data entry. They appear in the messages area at the bottom of the ATI screen and are listed in alphabetical order. Table 6-4. Device Message 0.0.0.0 is an invalid IP address Access level is Operator.
Page 63 Table 6-4. Device Message Limit of six Login IDs reached No Security Records to Delete Password Matching Error – Re-enter Password Please Wait Test Active 7990-A2-GB20-20 Entry Response Messages (2 of 2) What Message Indicates An attempt to enter a new login ID was made, and the limit of six login/password combinations has been...
Page 64 6. Monitoring and Troubleshooting Viewing DSL Error Statistics The unit maintains error statistics on the DSL interface. Statistics are maintained for up to 96 15-minute intervals (24 hours). To view the DSL Error Statistics, follow this menu selection sequence: Main Menu→Status→Performance Statistics→DSL Error Statistics main/status/performance/dsl_error Current Interval Timer: 002 --------------------------------------------------------------------------------...
Page 65 DSL Error Statistics are collected for: „ ES (Errored Seconds): Seconds during which one or more Cyclic Redundancy Check (CRC) errors or Loss of Sync Word (LOSW) defects has occurred. Maximum value is 900. „ SES (Severely Errored Seconds): Seconds during which 50 or more CRC anomalies or one or more LOSW defects has occurred.
Page 66 6. Monitoring and Troubleshooting Viewing DSL Performance Statistics DSL performance statistics allow you to monitor the current status of DSL operations. Performance statistics can assist you in determining the duration of specific conditions and provide a historical context for problem detection and analysis.
Page 67 DSL Performance Statistics are collected for: „ MrGn: The margin level calculated from the Signal to Noise Ratio (SNR) measured minus the SNR reference. The SNR reference is the value needed to maintain a bit error rate of 10 „ XmtPw: The transmit power level in dBm.
Page 68 6. Monitoring and Troubleshooting Viewing G.703 Performance Statistics (Model 7996) G.703 performance statistics allow you to monitor the current status of the G.703 interface operations. Performance statistics can assist you in determining the duration of specific conditions and provide a historical context for problem detection and analysis.
Page 69 „ CSS (Controlled Slip Seconds): Seconds during which one or more controlled slips (as defined in TR 54016) occurred. „ LOF (Loss of Frame Seconds): Contains the number of seconds that contain one or more LOF events. Maximum value is 900. „...
Page 70: Viewing Dsl Error Statistics
6. Monitoring and Troubleshooting Viewing Current DSL Performance Current DSL Performance Statistics provides a snapshot of the performance of the DSL port. These are the same values displayed for the current interval the DSL Error Statistics screen (see DSL Performance Statistics screen (see page 6-12).
Page 71 „ UAS (Unavailable Seconds): Seconds during which service is unavailable. UAS begins at the start of 10 consecutive SES and cleared at the start of 10 seconds with no SES. Maximum value is 900. „ LOSWS (Loss Of Sync Word Seconds): Seconds during which the SHDSL line had a Loss of Sync Word defect.
Page 72: Using The Display Leds Screen
6. Monitoring and Troubleshooting Using the Display LEDs Screen The status of the front panel LEDs can be viewed locally and remotely on the Display LEDs Status screen. There are three classes of LEDs: „ The SYSTEM LEDs display the status of the unit „...
Page 73: Front Panel Leds
Front Panel LEDs Table 6-5, Front Panel front panels. The following illustration shows the Hotwire 7995 TDM SHDSL front panel. Table 6-5. Label POWER ALARM TEST DTE (7995) G.703 (7996) * Slow Cycling: LED turns off and on in equal duration once per second.
Page 74: Viewing Identity Information
6. Monitoring and Troubleshooting Viewing Identity Information To view device identity information, follow this menu selection sequence: Main Menu→Status→Identity main/status/identity System Name: System Contact: System Location: -------------------------------------------------------------------------------- Use the Right and Left Arrow keys to scroll if more than 40 characters per field have been entered.
Page 75: Troubleshooting
„ DSL Hardware Revision: The 3-digit hardware revsion level of the DSL transceiver installed in the device. „ DSL Line Code: Displays SHDSL as the type of line code the device is using. Troubleshooting The unit is designed to provide many years of trouble-free service. However, if a problem occurs, refer to Table 6-6.
Page 76 6. Monitoring and Troubleshooting Table 6-6. Symptom No power, or the LEDs are not lit. Not receiving data. Power-On Self-Test fails. Only POWER and ALARM LEDs are on after power-on. 6-22 Troubleshooting (2 of 2) Possible Cause The power cord is not securely plugged into the wall receptacle or into the rear panel connection.
Page 77: Testing
Testing Accessing the Test Menu From the Test menu, you can run the following tests: „ DSL tests to start and stop tests on the DSL interface (Model 7995 only) „ DSL & G.703 tests to start and stop tests on the DSL and G.703 interface (Model 7996 only) „...
Page 78: Running Dsl Tests
7. Testing Running DSL Tests DSL tests require the participation of your network service provider. To access the DSL Tests screen, follow this menu selection sequence: Model 7995: Main Menu→Test→DSL Tests Model 7996: Main Menu→Test→DSL & G.703 Tests main/test/dsl Test -------------------------------------------------------------------------------- Local Loopbacks DSL Line Loopback:...
Page 79: Dsl Line Loopback
Use the Command column to start or stop a test. When the Status column shows that a test is Inactive, Start is displayed; when a test is Active, Stop is displayed. Position the cursor at the desired Start or Stop command and press Enter. The Results column displays the test duration.
Page 80: Repeater Loopback (Model 7996)
7. Testing G.703 Repeater Loopback (Model 7996) A G.703 Repeater Loopback (RLB) loops the signal being sent from the data port back to the data port. AIS is sent to the DSL port. Port Procedure To run a G.703 Repeater Loopback: 1.
Page 81: Dte Loopback (Model 7996)
G.703 DTE Loopback (Model 7996) A G.703 DTE Loopback loops the G.703 signal back to itself, retaining bipolar violation (BPV) transparency. Alarm Indication Signal (AIS) is sent to the DSL port while the DTE Loopback is active. All Ones Port Procedure To run a G.703 DTE Loopback: 1.
Page 82: Remote Send Line Loopback
7. Testing Remote Send Line Loopback The local unit initiates this test by sending a line loopback Up or Down command to the remote unit for 10 seconds. When the remote unit detects the loopback Up command, it puts itself into line loopback and lights the front panel test LED. The remote unit remains in loopback until it receives a loopback Down command or the remote unit’s test timeout value is exceeded.
Page 83: Send And Monitor 511 Pattern
Send and Monitor 511 Pattern The Send command is used to send a test pattern over the DSL interface. This test commands the remote unit to start sending and monitoring a 511 pattern, and then sends and monitors a 511 pattern. Ones are sent in the time slots that are mapped to the DSL port that is in test.
Page 84: Sync Data Port Tests (Model 7995)
7. Testing When a Send and Monitor 511 test is active, a count of bit errors is displayed next to the test duration, and the ResetMon virtual function key is available for use. Type r or R or select the ResetMon virtual function key to reset the error count. SYNC Data Port Tests (Model 7995) To access the SYNC Data Port Tests screen, follow this menu selection sequence: Main Menu→Test→SYNC Data Port Tests...
Page 85: Data Terminal Loopback
Data Terminal Loopback A Data Terminal Loopback (DTLB) loops user data back to the DTE. This loopback is located as closely as possible to the user data port (DTE) interface. All Ones Port Procedure To run a Data Terminal Loopback: 1.
Page 86: Data Channel Loopback
7. Testing Data Channel Loopback A Data Channel Loopback (DCLB) loops the data from the network interface back to the network. This loopback is located as close as possible to the user data port (DTE) interface. Port Procedure To run a Data Channel Loopback: 1.
Page 87: Repeater Loopback
Repeater Loopback A Repeater Loopback loops the signal being sent from the data port back to the data port. AIS is sent to the DSL port. All Ones Port Procedure To run an EIA-530 Repeater Loopback: 1. Position the cursor at the Start command next to Repeater Loopback on the SYNC Data Port Tests screen.
Page 88: Send Remote Data Channel Loopback
7. Testing Send Remote Data Channel Loopback The local termination unit can send an Up or Down sequence to request the start or stop of a Data Channel Loopback (DCLB) on a remote unit. Port Interface Procedure To send a Remote DCLB: 1.
Page 89: Device Tests
Device Tests The Device Tests branch is used to access the only endpoint-level test, the Lamp Test. To access the Device Tests screen, follow this menu selection sequence: Main Menu→Test→Device Tests main/test/card -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Ctrl-a to access these functions, ESC for previous menu Lamp Test The Lamp Test determines whether all LEDs are lighting and functioning properly.
Page 90: Ending An Active Test
7. Testing Ending an Active Test A test initiated by the user can be ended using: „ Test Timeout option – Enable the Test Timeout system option so the unit can automatically terminate tests, and set the Test Duration (min) option to specify the amount of time that tests can run before the unit terminates the test.
Page 91 7. Testing 7-15 7990-A2-GB20-20 September 2004...
Page 92 7. Testing 7-16 September 2004 7990-A2-GB20-20...
Page 93: A Configuration Options
Configuration Options Overview The tables in this appendix summarize the configuration options accessed when you select the Configuration option on the Main Menu. The Configuration options are arranged into groups based upon functionality. Select . . . DSL Port DSL Port Threshold Traps SYNC Port...
Page 94: Dsl Interface Options
A. Configuration Options DSL Interface Options For DSL Port Interface Options, refer to To access the DSL Interface Options screen, follow this menu selection sequence: Main Menu→Configuration→Current Configuration→DSL Port main/config/dsl_interface Circuit Identifier: -------------------------------------------------------------------------------- Ctrl-a to access these functions, ESC for previous menu Save Table A-1.
Page 95 Table A-1. DSL Interface Options (2 of 3) Max DSL Rate Possible settings depend on whether Spectrum Management is enabled. Determines the maximum speed for the DSL line when in Adaptive Rate mode (Max DSL Rate does not equal Min DSL Rate). See information about maximum payload rates for different DSL line rates.
Page 96 A. Configuration Options Table A-1. DSL Interface Options (3 of 3) Circuit Identifier Possible Settings: ASCII text field, Clear Default Setting: [blank] Uniquely identifies the circuit number of the transmission vendor’s DSL line for troubleshooting purposes. ASCII text field – Enter a maximum of 128 characters. All printable ASCII characters except the ^ (caret) are allowed.
Page 97 Table A-2. DSL Line Rate (kbps) 1032 1096 1160 1224 1288 1352 1416 1480 1544 1608 1672 1736 1800 1864 1928 1992 2056 * At 2056 kbps, 31 timeslots supported for G.704 framing, 32 timeslots for unframed. 7990-A2-GB20-20 G.703 EIA-530 Payload Rates Payload Rate 1024 1088...
Page 98: Dsl Port Threshold Trap Options
A. Configuration Options DSL Port Threshold Trap Options For DSL Port Threshold Trap Options, refer to Options. To access the DSL Threshold Trap Options screen, follow this menu selection sequence: Main Menu→Configuration→Current Configuration→DSL Port Threshold Traps NOTE: DSL Port Threshold Traps appears only when DSL Mode is set to STU-C (see Table A-6, System main/config/dsl_trap ES Trap Threshold:...
Page 99 A. Configuration Options Table A-3. DSL Port Threshold Trap Options ES Trap Threshold Possible Settings: 1–900, or 0 to Disable Default Setting: 120 Specifies the threshold for Error Seconds events in a 15-minute interval after which a trap will be sent. SES Trap Threshold Possible Settings: 1–900, or 0 to Disable Default Setting: 15...
Page 100: Synchronous Data Port Options For Model 7995
A. Configuration Options Synchronous Data Port Options for Model 7995 For Synchronous Data Port Options, refer to Options – Model follow this menu selection sequence: Main Menu→Configuration→Current Configuration→SYNC Ports main/config/sync_data -------------------------------------------------------------------------------- Ctrl-a to access these functions, ESC for previous menu Save Table A-4.
Page 101 Table A-4. Synchronous Data Port Options – Model 7995 (2 of 4) Payload Rate Possible Settings: 64 – 2304 kbps in 64k increments Default Setting: 192 kbps Specifies the payload rate of the port. This field is read-only unless the DSL Line Rate is 200 kbps (see only selections available.
Page 102 A. Configuration Options Table A-4. Synchronous Data Port Options – Model 7995 (3 of 4) Send All Ones on Data Port Not Ready Possible Settings: Both, Disable, DTR, RTS Default Setting: Both Specifies the conditions on the data port that determine when valid data is not being sent from the DTE.
Page 103 Table A-4. Synchronous Data Port Options – Model 7995 (4 of 4) Port (DTE) Initiated Loopbacks Possible Settings: Disable, DTLB, DCLB, Both Default Setting: Disable Allows the initiation and termination of a local Data Terminal Loopback (DTLB) or remote Data Channel Loopback (DCLB) by the DTE connected to this port. (DTLB is equivalent to a V.54 loop 3, and DCLB is equivalent to a V.54 loop 2.) Control of these loopbacks is through the DTE interchange circuits as specified by the V.54 standard.
Page 104: G.703 Interface Options For Model 7996
A. Configuration Options G.703 Interface Options for Model 7996 For G.703 Interface Options, refer to Model 7996. To access the G.703 Interface Options screen, follow this menu selection sequence: Main Menu→Configuration→Current Configuration→G.703 main/config/G.703 -------------------------------------------------------------------------------- Ctrl-a to access these functions, ESC for previous menu Save Table A-5.
Page 105 Table A-5. G.703 Interface Options – Model 7996 (2 of 2) Line Framing Possible Settings: CRC4, noCRC4 Default Setting: noCRC4 Specifies the framing format to be used by the G.703 interface. Line Framing appears only when DSL Mode is set to STU-C (see Options).
Page 106: System Options
A. Configuration Options System Options For System Options, refer to Options screen, follow this menu selection sequence: Main Menu→Configuration→Current Configuration→System main/config/system -------------------------------------------------------------------------------- Ctrl-a to access these functions, ESC for previous menu Save Table A-6. System Options (1 of 3) DSL Mode Possible Settings: STU-C, STU-R Default Setting: STU-R Controls whether the unit is configured as a SHDSL Transceiver Unit –...
Page 107 Table A-6. System Options (2 of 3) Test Timeout Possible Settings: Enable, Disable Default Setting: Enable Allows tests to end automatically. The feature should be enabled when the unit is remotely managed so that control can be regained after a test is accidentally executed. Enable –...
Page 108 A. Configuration Options Table A-6. System Options (3 of 3) Spectrum Management Possible Settings: Enable, Disable Default Setting: Disable For an STU-C, enabling spectrum management limits the DSL speeds on the unit to meet BT Access Network Spectrum standards. The purpose of Spectrum Management is to facilitate a reasonable spectral environment for the coexistence of multiple technologies in a loop plant with an acceptable level of crosstalk between them.
Page 109: Communication Port Options
Communication Port Options For Communication Port Options, refer to To access the Communication Port screen, follow this menu selection sequence: Main Menu→Configuration→Current Configuration→Communication Port When Port Use is set to Terminal, the following screen appears: main/config/com ------------------------------------------------------------------------------- Ctrl-a to access these functions, ESC for previous menu When Port Use is set to NetLink, the following screen appears: main/config/com -------------------------------------------------------------------------------...
Page 110 A. Configuration Options Table A-7. Communication Port Options (1 of 3) Port Use Possible Settings: Terminal, NetLink Default Setting: Terminal Specifies how the communications port is to be used. Terminal – The communication port is used for the asynchronous terminal interface. NetLink –...
Page 111 Table A-7. Communication Port Options (2 of 3) Stop Bits Possible Settings: 1, 1.5, 2 Default Setting: 1 Specifies the number of stop bits for the communication port. Stop Bits appears only when Port Use is set to Terminal. 1 – One stop bit. 1.5 –...
Page 112 A. Configuration Options Table A-7. Communication Port Options (3 of 3) Inactivity Timeout Possible Settings: Enable, Disable Default Setting: Disable Provides automatic logoff of a Telnet session. Inactivity Timeout appears only when Port Use is set to Terminal. Enable – The terminal session terminates automatically after the Disconnect Time. Disable –...
Page 113: Management And Communication Options Menu
Management and Communication Options Menu The Management and Communication Options Menu includes the following: „ Telnet Session Options „ Communication Protocol Options „ General SNMP Management Options „ SNMP NMS Security Options „ SNMP Traps Options Telnet Session Options Telnet Session configuration options control whether a Telnet session is allowed through an interconnected IP Network.
Page 114 A. Configuration Options Table A-8. Telnet Session Options Telnet Session Possible Settings: Enable, Disable Default Setting: Enable Specifies if the unit responds to a Telnet session request from a Telnet client on an interconnected IP network. Enable – Telnet sessions are allowed between the unit and a Telnet client. Disable –...
Page 115: Communication Protocol Options
Communication Protocol Options The Communication Protocol configuration options specify the information necessary to support the IP communication network, including IP address and link protocols. Initial values are determined by the configuration you currently have loaded. To access the Communication Protocol Options screen, follow this menu selection sequence: Main Menu→Configuration→Current Configuration→...
Page 116 A. Configuration Options Table A-9. Communication Protocol Options (1 of 2) Node IP Address Possible Settings: 001.000.000.000 – 223.255.255.255, Clear Default Setting: 000.000.000.000 Specifies the Node IP address. The IP address is not bound to a particular port, and can be used for remote access over the EOC.
Page 117 Table A-9. Communication Protocol Options (2 of 2) Communication Port Subnet Mask Possible Settings: 000.000.000.000 – 255.255.255.255, Clear Default Setting: 000.000.000.000 Specifies the unit’s Communication Port Subnet Mask when the unit is configured as a network communication link. Communication Port Subnet Mask is used only when Port Use is set to Net Link (see (000.000.000.000), the node IP Address and subnet mask are used.
Page 118: General Snmp Management Options
A. Configuration Options General SNMP Management Options To access the General SNMP Management Options screen, follow this menu selection sequence: Main Menu→Configuration→Current Configuration→ Management and Communication→General SNMP Management main/config/management/SNMP SNMP Management: Community Name 1: Name 1 Access: Community Name 2: Name 2 Access: ------------------------------------------------------------------------------- Ctrl-a to access these functions, ESC for previous menu...
Page 119 A. Configuration Options Table A-10. General SNMP Management Options SNMP Management Possible Settings: Enable, Disable Default Setting: Enable Enables or disables the SNMP management features. Enable – Enables SNMP management capabilities. Disable – Disables SNMP management capabilities. Community Name 1 Possible Settings: ASCII text field, Public, Clear Default Text: Public Identifies the name of the community allowed to access the unit’s MIB.
Page 120: Snmp Nms Security Options
A. Configuration Options SNMP NMS Security Options To access the SNMP NMS Security Options screen, follow this menu selection sequence: Main Menu→Configuration→Current Configuration→ Management and Communication →SNMP NMS Security NOTE: SNMP NMS Security is avaialble for IP Complex configurations only. main/config/management/security 1 IP Address: 2 IP Address:...
Page 121 A. Configuration Options Table A-11. SNMP NMS Security Options NMS IP Validation Possible Settings: Enable, Disable Default Setting: Disable Specifies whether security checking is performed on the IP address of SNMP management systems attempting to access the node. Enable – Security checking is performed on the IP address of SNMP management systems attempting to access the node.
Page 122: Snmp Traps Options
A. Configuration Options SNMP Traps Options An SNMP trap can be automatically sent out through the EOC or the Management port to an SNMP manager when the Hotwire TDM SHDSL endpoint detects conditions set by the user. Refer to Traps, for details of SNMP traps supported by the endpoint. To access the SNMP Traps Options screen, follow this menu selection sequence: Main Menu→Configuration→Current Configuration→...
Page 123 Table A-12. SNMP Traps Options (1 of 2) SNMP Traps Possible Settings: Enable, Disable Default Setting: Enable Controls the generation of SNMP trap messages. Enable – SNMP trap messages are sent out to SNMP managers. Disable – No SNMP trap messages are sent out. NMS n IP Address Possible Settings: 001.000.000.000 –...
Page 124 A. Configuration Options Table A-12. SNMP Traps Options (2 of 2) Enterprise Specific Traps Possible Settings: Enable, Disable Default Setting: Disable Determines if SNMP traps are generated for enterprise-specific events. Enable – SNMP traps are generated for enterpriseSpecific events. Disable – No enterprise-specific event traps are sent. NOTE: Refer to SNMP Traps.
Page 125: B Standards Compliance For Snmp Traps
Standards Compliance for SNMP Traps SNMP Traps This section describes the unit’s compliance with SNMP standards and any special operational features for the SNMP traps supported. The unit supports the following traps: „ warmStart „ authenticationFailure „ linkUp and linkDown „...
Page 126: Warmstart
B. Standards Compliance for SNMP Traps warmStart Table B-2. SNMP Trap warmStart authenticationFailure Table B-3. SNMP Trap authenticationFailure warmStart Trap Description The unit has reinitialized itself. The trap is sent after the unit resets and stabilizes. There are no variable bindings.
Page 127: Linkup And Linkdown
linkUp and linkDown The link SNMP traps are: „ linkUp – The unit recognizes that one of the communication interfaces is operational. „ linkDown – The unit recognizes that one of the communication interfaces is not operational. The network and synchronous port interfaces (physical sublayer) are represented by an entry in the MIB-II Interfaces table and supported by the DS1 MIB.
Page 128 B. Standards Compliance for SNMP Traps Table B-4. linkUp/Down variable bindings (continued) fType (RFC 2863) This object is the type of interface: – e1(19) Used for G.703 interface – propPointToPointSerial(22) Used for EOC. – ppp(23) Used for the COM Port when configured for PPP. –...
Page 129: Enterprise-Specific Traps
Enterprise-Specific Traps The enterpriseSpecific trap indicates that an enterprise-specific event has occurred. The Specific-trap field identifies the particular trap that occurred. Table B-5, Enterprise-Specific by the unit. Table B-5. SNMP Trap enterprisePrimary- ClockFail(1) enterpriseSelfTest- Fail(2) enterpriseDevice- Fail(3) enterpriseTestStart(5) enterpriseConfig- Change(6) enterprisePrimary- ClockFailClear(101) 7990-A2-GB20-20...
Page 130 B. Standards Compliance for SNMP Traps Table B-5. SNMP Trap enterpriseTest- Stop(105) Tests that affect the enterpriseTestStart and enterpriseTestStop traps and the variable bindings depend on the interface. The specific tests and variable bindings are described in Table B-6. Interface DSL Network Enterprise-Specific Traps (2 of 2) Description...
Page 131 Table B-6. Interface G.703 EIA-530-A 7990-A2-GB20-20 B. Standards Compliance for SNMP Traps Tests Affecting enterpriseTestStart/Stop Traps (2 of 2) enterpriseTestStart/Stop variable bindings ifIndex (RFC 2863) ifAdminStatus (RFC 2863) ifOperStatus (RFC 2863) ifType (RFC 2863) ifTestType (RFC 2863) The following objects control tests in SNMP-managed devices: –...
Page 132 B. Standards Compliance for SNMP Traps September 2004 7990-A2-GB20-20...
Page 133: Overview
Connectors, Cables, and Pin Assignments Overview The following sections provide pin assignments for: „ Power Input Connector „ COM Port Connector „ COM Port-to-PC Cable „ COM Port-to-LAN Adapter Cable „ G.703 Network Interface „ EIA-530-A Port „ EIA-530-A-to-X.21 Interface „...
Page 134: Power Input Connector
C. Connectors, Cables, and Pin Assignments Power Input Connector The input power connector leads are shown in Pin 1 is at the lower right of the connector and Pin 6 at the upper left as you face the back of the unit. Table C-1.
Page 135: Com Port-To-Pc Cable
COM Port-to-PC Cable The COM port can be connected to an asynchronous terminal or a PC running terminal emulation software. The COM port-to-PC cable is a 14-foot, 26 AWG, 8-conductor cable with an 8-position unkeyed modular connector and a DB9 socket connector.
Page 136: Com Port-To-Lan Adapter Cable
C. Connectors, Cables, and Pin Assignments COM Port-to-LAN Adapter Cable The COM port can be configured for network management and attached to an Ethernet LAN adapter. The COM port-to-LAN adapter cable is a 14-foot, 24 AWG, 6-conductor cable with an 8-position unkeyed modular connector at either end. Figure C-2, COM Port-to-PC Cable (Feature Number (DCE) Tx Clock...
Page 137: Network Interface
G.703 Network Interface The G.703 interface is either two BNC connectors (Transmit and Receive) for a 75-Ohm unbalanced interface, or an 8-position, unkeyed modular connector for a 120-ohm balanced interface. See Connector, and (Feature Number Table C-3. E1 120-Ohm Balanced Interface Connector Signal Receive Ring Receive Tip...
Page 138: Eia-530-A Port
C. Connectors, Cables, and Pin Assignments EIA-530-A Port The EIA-530-A Port interface connector information is shown in EIA-530-A Port Interface Table C-4. EIA-530-A Port Interface Connector Signal Shield Signal Common Signal Common Transmitted Data Received Data Request to Send Clear to Send Received Line Signal Detector DCE Ready DTE Ready...
Page 139: Eia-530-A-To-X.21 Interface
EIA-530-A-to-X.21 Interface The EIA-530-A-to-X.21 adapter cable Feature Number X.21 Cable DB25 SIGNAL PLUG TD-A TD-B RD-A RD-B RXC-A RXC-B RTS-A RTS-B RLSD-A RLSD-B SIG. COMMON TT-A TT-B Figure C-4. 7990-A2-GB20-20 C. Connectors, Cables, and Pin Assignments (Figure C-4, EIA-530-A-to-X.21 (Cable 7900-F1-504)) provides the X.21 interface shown in Interface.
Page 140 C. Connectors, Cables, and Pin Assignments Table C-5. X.21 Cable Interface Signal Signal Common Transmitted Data Received Data Request to Send Data Channel Received Line Signal Detector Transmit Signal Element Timing (DTE Source) Receiver Signal Element Timing (DCE Source) ITU-T Number September 2004 Direction...
Page 141: Eia-530-A-To-Rs-449 Interface
EIA-530-A-to-RS-449 Interface The EIA-530-A-to-RS-449 adapter cable Pinouts (Feature Number Table C-6, RS-449 Cable DB25 SIGNAL PLUG SHIELD TD-A TD-B RD-A RD-B TXC-A TXC-B RXC-A RXC-B RTS-A RTS-B CTS-A CTS-B RLSD-A RLSD-B SIG. COMMON RCV. COMMON TT-A TT-B SIG. COMMON Figure C-5. 7990-A2-GB20-20 C.
Page 142 C. Connectors, Cables, and Pin Assignments Table C-6. RS-449 Cable Interface Signal Shield Signal Ground Receive Ground Send Common Send Data Receive Data Request to Send Clear to Send Receiver Ready Data Mode Terminal Ready Terminal Timing Send Timing Receive Timing Local Loopback Remote Loopback Test Mode...
Page 143: Eia-530-A-To-V.35 Interface
EIA-530-A-to-V.35 Interface The EIA-530-A-to-V.35 adapter cable or adapter Adapter Cable (Feature Number 7900-F1-503) and EIA-530-A-to-V.35 Adapter (Feature Number 7900-F1-516) Table C-7, V.35 Cable Pin 1 DB25 SIGNAL PLUG SHIELD TD-A TD-B RD-A RD-B TXC-A TXC-B RXC-A RXC-B RLSD SIG. COMMON TT-A TT-B SIG.
Page 144 C. Connectors, Cables, and Pin Assignments Table C-7. V.35 Cable Interface Signal Shield Signal Common Transmitted Data Received Data Request to Send Clear to Send Data Channel Received Line Signal Detector Data Set Ready Data Terminal Ready Transmit Signal Element Timing (DTE Source) Transmit Signal Element Timing (DCE Source) Receiver Signal Element Timing (DCE Source) Local Loopback...
Page 145: Dsl Network Interface Cable
DSL Network Interface Cable The DSL line interface cable is a 20-foot, 24 AWG solid, 2-twisted-pair cable that is RJ48C-to-RJ48C. See Figure C-7, DSL Network Interface Cable with RJ48C Connector (Feature Number 7900-F1-514). Table C-8. DSL Network Interface Connector DSL Signal (Unused) (Unused) Ring...
Page 146 C. Connectors, Cables, and Pin Assignments C-14 September 2004 7990-A2-GB20-20...
Page 147: Technical Specifications
Technical Specifications Table D-1. Technical Specifications for the Hotwire TDM SHDSL Standalone Specifications Size Weight Approvals Safety Certifications Power Cables Physical Environment Operating temperature Storage temperature Relative humidity * Technical specifications are subject to change without notice. 7990-A2-GB20-20 Endpoints, Models 7995 and 7996 Criteria* Width: 18.4 cm (7.25 inches)
Page 148 D. Technical Specifications September 2004 7990-A2-GB20-20...
Page 149 Index AC transformer, connecting, 3-2 access SNMP, 5-6 to asynchronous terminal interface, 2-3 to user interface, resetting/restoring, 5-5 access level COM port, A-19 Community Name 1, A-27 Community Name 2, A-27 effective, 5-2 functions available for, 5-2 Telnet session, A-22 access type NMS, A-29 Action on Network LOS Alarm, A-10...
Page 150 Index connectors COM Port, C-2 G.703 Network Interface, C-5 location on unit, 1-5 power input, C-2 rear panel, C-1 Control branch Administer Logins, 5-3 Change Identity, 3-5 Download Code, 3-16 Reset AutoRate, 3-16 Reset Device, 3-14 Control Sync Port Data Rate, 4-4 create login ID, 5-3 current DSL performance, 6-16 customer configuration, 3-7...
Page 151 SNMP Management Options, A-26 Traps, enabling, A-31 glossary, vi health and status messages, 6-3 identity entering, 3-5 viewing, 6-20 inactivity timeout for communication port use, A-20 for Telnet session, A-22 initial startup and configuration, 3-1 internal switches, 4-2 invalid entry messages, 6-8 IP address invalid, 6-8 NMS, A-29...
Page 152 Index performance statistics, 6-12 G.703, 6-14 physical environment requirements, D-1 pin assignments, C-1 Port Access Level, A-19 interface cable, C-3 LAN Adapter cable, C-4 pinouts, C-2 Type, A-8 power cord installation, 3-2 input connector, C-2 optional power sources, C-2 LED, 6-19 problems, 6-20 requirements, D-1 supply...
Page 153 inactivity timeout, A-22 login required, A-22 options, A-21 terminal communication parameters, 3-4 connecting, 3-4 port, direct connection, 2-1 settings required, 3-4 Test aborting, 7-14 Data Channel Loopback, 7-10 Terminal Loopback, 7-9 Device, 7-13 DTE Loopback G.703, 7-5 Duration, A-15 G.703 Repeater Loopback, 7-4 LED, 6-19 Line Loopback, 7-3 Network...
Page 154 Index IN-6 September 2004 7990-A2-GB20-20...

This manual is also suitable for:

Hotwire 7996 Hotwire 7995-a2-411 Hotwire 7995-a2-421 Hotwire 7995-a2-422 Hotwire 7995-a2-700 Hotwire 7996-a2-410 ... Show all

Paradyne Hotwire 7995 User Manual

About this Guide

1 About the TDM SHDSL Endpoint

2 Using the Asynchronous Terminal Interface

3 Initial Startup and Configuration

4 Configuring the Unit Using the Internal Switches

5 Security

6 Monitoring and Troubleshooting

7 Testing

A Configuration Options

B Standards Compliance for SNMP Traps

Quick Links

Troubleshooting

Related Manuals for Paradyne Hotwire 7995

Summary of Contents for Paradyne Hotwire 7995

This manual is also suitable for:

Table of Contents