Table of Contents
Advertisement
(3-6) SYSTEM EXCLUSIVE MESSAGE
(3-6-1) UNIVERSAL NON-REALTIME MESSAGE
(3-6-1-1)
GENERAL MIDI MODE ON
F0H 7EH 7FH 09H 01H F7H
Resets the following controllers to the indicated values.
VOLUME
PAN
PROGRAM CHANGE
BANK SELECT MSB
REVERB DEPTH
Pitchbend change
Modulation
Expression
Sustain Switch
SOSTENUTO SWITCH
RPN
Portamento control
MIDI master volume
Pitchbend sensitivity
Fine tuning
Coarse tuning
(3-6-1-2)
IDENTITY REQUEST (Receive only)
F0H 7EH 0nH 06H 01H F7H (where n is the Device No. But message is valid regardless of device ("omni")).
(3-6-1-3)
IDENTITY REPLY (Send only)
F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H 01H F7H
dd; Device Number Code
If QS300:
48
If B900:
4C
If SDX3000:
62
(3-6-2) UNIVERSAL REALTIME MESSAGE
(3-6-2-1)
MIDI MASTER VOLUME
F0H 7FH 7FH 04H 01H llH mmH F7H
Changes the Master Volume value, where mm gives the new volume setting. (Byte ll is ignored.)
(3-6-3) PARAMETER CHANGE
(3-6-3-1)
MIDI MASTER TUNING
F0H 43H 1nH 27H 30H 00H 00H mmH llH ccH F7H
Changes the Master Tune value, where mm and ll give the new setting, as described below. (Values n and cc are ignored.)
T = M*200/256-100
where
T
: Actual tuning value (-99 ~ +99)
M : One-byte value, where bits 0 to 3 of mm give the high-order nibble, and bits 0 to 3 of ll give the low-order nibble.
(3-6-3-2)
XG SYSTEM ON
11110000
01000011
0001nnnn
01001100
0aaaaaaa
0aaaaaaa
0aaaaaaa
00000000
11110111
This message switches the SYSTEM MODE to XG. The message requires approximately 50ms to execute, so sufficient time should be allowed before the next message is sent.
The message resets all controllers. It also resets to their defaults all MultiPart and Multieffect values (see appended tables), as well as the Whole System values denoted by "(XG)" (again,
see appended table).
(3-6-3-3)
XG PARAMETER CHANGE
11110000
01000011
0001nnnn
01001100
0aaaaaaa
0aaaaaaa
0aaaaaaa
0ddddddd
|
11110111
Data size matches parameter size (2 or 4 bytes). For address and byte count, refer to attached table.
The following four data types can be sent or received. (The unit will send only upon receipt of a Parameter Change Request.)
System data
Multieffect data
Multipart data
Drums setup data
MIDI Data Format
100
Center
1
(Grandpno)
0
4
0
(center)
0
(off)
127 (max)
0
(off)
0
(off)
Null (Internal data remains unchanged.)
Reset
127 (max)
02
(2 semitones)
0
0
01
01
01
F0
Exclusive status
43
YAMAHA ID
1n
Device Number
4C
Model ID
00
Address High
00
Address Mid
7E
Address Low
00
Data
F7
End of Exclusive
F0
Exclusive status
43
YAMAHA ID
1n
Device Number
4C
Model ID
aaaaaaa
Address High
aaaaaaa
Address Mid
aaaaaaa
Address Low
ddddddd
Data
|
F7
End of Exclusive
(Ignored if Voice Mode)
(Ignored if Voice Mode)
40
Hide quick links:
Advertisement
Table of Contents
