ADEMCO 5881KEY Installation And Setup Manual

INTRODUCTION
The 5881KEY RF receiver is designed for use with control
panels that support an RF receiver connection via the remote
keypad connection points . The receiver recognizes alarm,
status and keypad control messages only from 5804 and
5804BD wireless key transmitters. These messages are sent
via wired connections from the receiver to the control, which
then initiates the appropriate action (arm or disarm the system,
etc.). When using the 5804BD 2-way wireless key (in
conjunction with a 5800TM module), system status and other
conditions are sent to the 5804BD which then provides
appropriate indications of these conditions.
One or two individually identified receivers can be employed,
depending on the control used. Connection of multiple
receivers to a control can provide redundant coverage or
extend coverage in large areas. Multiple receivers do not
increase the number of wireless keypads that the system can
support. See the control's instructions for specific information
regarding the number of receivers that can be supported.
This receiver features a Spatial Diversity System which
virtually eliminates the possibility of "Nulls" and "Dead Spots"
within the coverage area.
The instruction manual that accompanies the control includes
recommendations regarding receiver locations, the types of
wireless zones that can be programmed and the procedure for
programming the receiver.
This receiver should not be installed in an area subject to
environmental extremes of below freezing (such as an
unheated warehouse) or extremely high temperatures (such as
an attic).
INSTALLATION
With some controls, a receiver may be mounted directly inside
the control's cabinet (receiver circuit board only, without its
plastic housing) instead of remotely (in its own housing). In
both cases, avoid mounting the receiver antennas against a
NOTE: WHEN CIRCUIT BOARD IS MOUNTED IN
CONTROL'S CABINET, GROUNDING LUGS (2)
PROVIDED MUST BE INSERTED IN LEFT-HAND
TERMINALS OF ANTENNA BLOCKS AND
SECURED TO CABINET (SEE RECEIVER'S AND
CONTROL'S INSTRUCTIONS)
MOUNTING
HOLES
INSTALLATION AND
SETUP GUIDE
metal surface. Refer to the control's Installation and Setup
Guide for detailed procedures regarding mounting the receiver
either in the control cabinet, or remotely.
Setting Up the Receiver
1. Setting The DIP switches on the Receiver:
2. Insert the wiring plug (with 4 flying leads) into the
3. Install the antennas in the right-hand terminals of the two
4. Replace the receiver's cover if the receiver is not
5. Proceed with any programming of the control that
6. The LED located on the receiver's circuit board should
7. Perform a wireless Go/No Go test in accordance with
ANTENNAS
INSERT IN
RIGHT-HAND
TERMINALS
DIP
SWITCH
INTERFERENCE
INDICATOR
LED
DIP SWITCH: WHITE AREAS = SWITCH HANDLES
POSITIONS 2-4: DETERMINE RECEIVER'S ADDRESS.
TO RELEASE BOARD,
CONSULT CONTROL'S INSTRUCTIONS
BEND BACK TABS (2).
FOR ADDRESS TO USE. DIP SWITCH
SHOWN SET FOR ADDRESS "0"
Set the receiver's DIP switch to identify the receiver's
address (refer to the DIP switch chart in the Diagram
below).
mating socket on the receiver (see Diagram below for
socket location). Connect the 4 wires to the control's
corresponding remote keypad connection points (see
"Interface Wiring" in the SPECIFICATIONS section).
terminal blocks at the upper edge of the circuit board, one
into each block's right-hand terminal, and tighten the
screws to secure them.
If the receiver is mounted in a cabinet, insert the antennas
through the holes in the cabinet's top first, and then into
the terminal blocks.
mounted within a cabinet.
may be necessary for RF Receiver operation, and for
the 5804 and 5804BD wireless keys, as described in the
control's Installation and Setup Guide.
Note: When using a 5804BD 2-way wireless keypad, a
5800TM module must be connected to the control.
be used as an indicator of strong local radio frequency
interference. If this LED is continuously illuminated, the
receiver should be relocated.
the procedures provided in your control's Installation and
Setup Guide.
THIS DEVICE COMPLIES WITH PART 15 OF FCC
RULES.
OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS
DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.
YELLOW
RED
BLACK
GREEN
PLUG
AND
SOCKET
ON OFF
N7635-2 5/99
5881KEY
RF RECEIVER
}
TO CONTROL'S REMOTE
KEYPAD CONNECTION
POINTS. EACH RECEIVER
MUST BE ON INDIVIDUAL
HOME RUN.
USE MAX OF 220 FT (67M)
OF #22 (0.64MM) WIRE OR
550 FT (168M) OF #18
(1MM) WIRE FOR EACH
RUN (3 FT MAX FOR UL
INSTALLATION . . . . SEE
INSTRUCTIONS.
SWITCH RECEIVER ADDRESS SETTINGS
POSITION ("—" means "OFF")
0 1 2 3 4 5 6 7
4 — ON — ON — ON — ON
3 — — ON ON — — ON ON
2 — — — — ON ON ON ON
1 FOR FUTURE USE