Advertisement
Quick Links
Advertisement
Related Manuals for Yamaha YHT-23
Summary of Contents for Yamaha YHT-23
- Page 1 YHT-23 QUICK-CONNECT GUIDE...
-
Page 3: Tools And Parts
In addition to enhancing the sound of a video source, like your TV, DVD player, or VCR, the YHT-23 also superbly reproduces audio sources, such as a CD player or a cassette deck. -
Page 4: Audio Components
YHT-23 Q Yamaha HTR-5240 Receiver (Rear Panel) NOTE: For your convenience, the Yamaha HTR-5240 receiver is equipped with two switched ac outlets (100 W max.). If desired, use them to power on connected components (e.g., CD player or turntable) each time the receiver is turned on. - Page 5 YHT-23 S ONNECTING NS-A327 (Front Right) Clear/ Clear Stripe Wire Wire Initial STANDBY/ON HIGH CUT VOLUME Settings (on Front Panel) 50 Hz 150 Hz Yamaha HTR-5240 A/V Receiver (Rear Panel Speaker Terminals) Clear/ Clear Stripe Wire Wire Speaker Wiring NS-A327...
- Page 6 YHT-23 S ONNECTING NS-A327 (Front Right) Clear/ Clear Stripe Wire Wire STANDBY/ON HIGH CUT VOLUME 50 Hz 150 Hz Initial Settings (on Front Panel) Yamaha HTR-5240 A/V Receiver (Rear Panel Speaker Terminals) Clear/ Clear Stripe Wire Wire Speaker Wiring NS-A327...
-
Page 7: Satellite Receiver
IDEO OMPONENTS Yamaha HTR-5240 Receiver (Rear Panel) NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5240 receiver. VIDEO SIGNAL VIDEO DVD/LD SAT/D-TV... - Page 8 Red = Right Audio *Analog Audio Out connections are required for playback of CD-Rs and recording from DVD to VCR. YHT-23 Q Yamaha HTR-5240 Receiver (Rear Panel) Use an RCA Video Cable And Jacks For Video Interconnections DVD/LD U I C K...
- Page 9 MD recorder, or VCR. To record programs from a source (e.g., laserdisc player), connect the source unit to the DVD/LD (or SAT/D-TV) AUDIO SIGNAL input terminals. Yamaha HTR-5240 Receiver (Rear Panel) DVD/LD Video Out Audio L Out...
- Page 10 IDEO OMPONENTS Yamaha HTR-5240 Receiver (Rear Panel) NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5240 receiver. AUDIO SIGNAL DVD/LD SAT/D-TV Use RCA Audio Cables And Jacks For Audio Interconnections...
- Page 11 ABLE ASIC NOTE: When using a hi-fi stereo VCR, set the Tuner/Line switch (on the VCR) to Line position to record from another source connected to the Yamaha HTR-5240 receiver. ANT In Basic Cable (From Wall Jack) Descrambler Premium Cable...
- Page 12 HTR-5240 receiver and most Yamaha audio components. To program other brands of compo- nents (i.e., TV, VCR, etc.) or if your Yamaha unit does not respond, you will need to program the remote control with the manufacturer’s codes (listed on the back pages of the HTR-5240 Owner’s Manual).
- Page 13 5. To verify the code works, aim the remote control at the VCR, press VCR, and then press POWER. The VCR should turn off. If it doesn’t respond, use another code for the same manufacturer and repeat steps 3 through 5. YHT-23 Q EMOTE ONTROL ONTINUED ETTING 1.
-
Page 14: Playing A Dvd
> (forward button) to start play. NOTE: The DVD player’s controls are now assigned to the remote control buttons, since DVD was the last selected component. YHT-23 Q EMOTE ONTROL ESETTING You can reset the remote control to factory codes for all... - Page 16 ©2000 YAMAHA ELECTRONICS CORPORATION, USA 6660 Orangethorpe Avenue, Buena Park, CA 90620 PH: (714) 522-9105; FAX: (888) 435-7922 http://www.yamaha.com...