Page 1
CDP-EX880/MS717 SERVICE MANUAL AEP Model UK Model CDP-EX880 E Model Tourist Model CDP-MS717 CDP-EX880/MS717 are the CD player section in DHC-EX880MD/MD717. Photo: CDP-MS717 Model Name Using Similar Mechanism HCD-MD515 CD Mechanism Type CDM48B-5BD29 Base Unit Type BU-5BD29 Optical Pick-up Type...
SELF DIAGNOSTIC FUNCTION (d) The status, when judged NO DISC error. This set can display the error history using the self diagnostic func- “3 ” : Stop tion. “4 ” : Set up “5 ” : TOC read 1. OPERATING THE DISPLAYED HISTORYS “6 ”...
LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
Page 4
POWER SUPPLY DURING SERVICING CAUTION • As this set has not own power supply, it does not operate inde- Use of controls or adjustments or performance of procedures pendently. other than those specified herein may result in hazardous ra- Therefore, during servicing, connect it to the Pre-Main ampli- diation exposure.
Page 5
CD-TEXT TEST DISC This unit is able to display the test data (character information) written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313:4-989-366-01) is used for checking the display. To check, perform the following procedure. Checking Method: 1.
Page 6
Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is no a fault.) TRACK Recorded contents Display ! ” # $ % & ´ (21h to 27h)1kHz 0dB L&R N All the same + , –...
SECTION 3 DISASSEMBLY Note: Follow the disassembly procedure in the numerical order given. 2 screw CASE (BVTT3 × 6) 3 case 1 two screws (case 3 TP2) 1 two screws (case 3 TP2) FRONT PANEL SECTION 4 front panel section 3 claw 2 three screws (BVTT3 ×...
Page 9
MECHANISM DECK SECTION (CDM48B-5BD29) , MAIN BOARD 6 two PC board holders 3 mechanism deck section 5 two screws (CDM48B-5BD29) (BV3 × 10) 7 MAIN board 1 connector (CN201) 1 flat wire (11 core) (CN321) 1 connector (CN322) 4 three connectors (CN391, 392, 393) 4 flat wire (CN331)
Page 10
BASE UNIT (BU-5BD29) 2 Remove the base unit (BU-5BD29) to direction of the arrow. 1 two screws 1 two screws (BV3 × 8) (BV3 × 8) TRAY (SUB) ASS’Y 2 tray (sub) ass’y 1 Pull the slider (selection). – 10 –...
SECTION 4 SECTION 5 TEST MODE ELECTRICAL ADJUSTMENTS • AGING MODE Notes: 1. How to Enter AGING Mode 1. CD Block basically constructed to operated without adjustment. Therefore, check eaech item in order given. 1) Insert a disc into the CD player. 2.
Page 14
2. RF LEVEL CHECK Adjustment Location : Connection: [BD BOARD] – Side B – oscilloscope BD board TP (RF) TP (VC) – Procedure: 1. Connect the oscilloscope to TP (RF) and TP (VC) on BD board. 2. Turned power switch on. IC102 [ ] 3.
6-7. IC PIN FUNCTION DESCRIPTION • MAIN BOARD IC301 µPD784215GF-516-3BA (SYSTEM CONTROLLER) Pin No. Pin Name Function 1, 2 Not used (open) LED LAT Serial data latch pulse output to the LED driver (IC602) “L” active DRV CS Chip select signal output to the fluorescent indicator tube driver (IC601) “L” active Data read enable signal output to the S-RAM (IC315) “L”...
Page 20
Pin No. Pin Name Function Main system clock input terminal (12.5 MHz) — Ground terminal Sub system clock output terminal Not used (open) Sub system clock input terminal Not used (fixed at “L”) System reset signal input from the reset signal generator (IC311) “L”: reset RESET For several hundreds msec.
4-995-074-01 KNOB (JOG) * 13 A-4724-092-A MAIN BOARD, COMPLETE X-4949-032-1 PANEL ASSY, FRONT 4-965-822-01 FOOT 4-962-708-01 EMBLEM (4-A), SONY 4-951-620-41 SCREW (2.6), +BVTP X-4949-035-1 LID ASSY 1-783-102-11 WIRE (FLAT TYPE) (5 CORE) 1-667-599-11 LED BOARD 1-783-104-11 WIRE (FLAT TYPE) (17 CORE)
Page 23
(2) MECHANISM DECK SECTION-1 (CDM48B-5BD29) not supplied supplied M501 BU-5BD29 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 51 4-993-146-01 HOLDER, BU 4-964-466-01 GEAR (JOINT) 4-948-503-01 SPRING (BU), COMPRESSION * 61 4-967-875-01 REINFORCEMENT (PLATE CAM) 3-383-699-01 CLAMP (EDGE) * 62 1-651-396-11 U/D MOTOR BOARD...
Page 24
(3) MECHANISM DECK SECTION-2 (CDM48B-5BD29) (including r A) not supplied not supplied not supplied M502 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark * 101 X-4948-784-1 CHASSIS ASSY, SUB * 123 1-651-392-11 MID SW BOARD 4-964-476-01 BELT (R) 4-964-484-01 SPRING (LEVER R), TORSION 3-319-030-01 BELT (MIDWAY) 4-964-492-01 BASE (MAGNET), FITTING...
Page 25
(4) BASE UNIT SECTION (BU-5BD29) M101 M102 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark ! 151 8-848-379-31 OPTICAL PICK-UP KSS-213BA/F-NP...
SECTION 8 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark ! or dotted line with mark parts list may be different from the parts speci- are seldom required for routine service.
Page 27
COUNT SW DISC DETECTION (A) DISC DETECTION (B) IN SW Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < RESISTOR > R181 1-216-025-00 RES,CHIP 1/10W R182 1-216-025-00 RES,CHIP 1/10W R102 1-216-001-00 METAL CHIP 1/10W R183 1-216-025-00 RES,CHIP 1/10W R104 1-216-093-00 METAL CHIP...
Page 28
JACK MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-667-598-16 JACK BOARD R562 1-249-429-11 CARBON 1/4W R563 1-249-429-11 CARBON 1/4W *********** < CAPACITOR > R564 1-249-429-11 CARBON 1/4W R565 1-249-429-11 CARBON 1/4W C501 1-136-153-00 FILM 0.01uF R566 1-249-429-11 CARBON...
Page 29
MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C327 1-162-282-31 CERAMIC 100PF C334 1-164-159-11 CERAMIC 0.1uF < IC > C335 1-164-159-11 CERAMIC 0.1uF IC201 8-759-158-62 IC TA78057S C336 1-164-159-11 CERAMIC 0.1uF IC211 8-759-604-86 IC M5F7807L C343 1-162-290-31 CERAMIC 470PF...