Fisher & Paykel CI365DTTB1 Installation Manual
Modular cooktop
Hide thumbs
Also See for CI365DTTB1:
- User manual (25 pages) ,
- User manual (31 pages) ,
- User manual (31 pages)
Related Manuals for Fisher & Paykel CI365DTTB1
Summary of Contents for Fisher & Paykel CI365DTTB1
- Page 1 MODULAR COOKTOP MULTIPLE PRODUCT WITH OVERHEAD VENTILATION CI365DTTB1, CI304DTTB1, CI244DTTB1, CI152DTTB1, CI152DB1, CI122DB1, CIT122DX1, CIT152DX1 models INSTALLATION GUIDE US CA...
-
Page 2: Safety And Warnings
SAFETY AND WARNINGS WARNING! Electric Shock Hazard Failure to follow this advice may result in electric shock or death. • Do not cook on a broken or cracked cooktop. If the cooktop surface should break or crack, switch the appliance off immediately at the mains power supply (wall switch) and contact a qualified technician. - Page 3 SAFETY AND WARNINGS WARNING! Hot Surface Hazard Failure to follow this advice may result in death. • DO NOT TOUCH SURFACE UNITS OR AREAS NEAR UNITS – Surface units may be hot even though they are dark in color. • During use, accessible parts of this appliance will become hot enough to cause burns.
- Page 4 SAFETY AND WARNINGS WARNING! Health Hazard Failure to follow this advice may result in death. • This appliance complies with electromagnetic safety standards. However, persons with cardiac pacemakers or other electrical implants (such as insulin pumps) must consult with their doctor or implant manufacturer before using this appliance to make sure that their implants will not be affected by the electromagnetic field.
- Page 5 SAFETY AND WARNINGS Use proper pan size — This appliance is equipped with one or more surface units of different size. Always place small pans in the centre of the cooking zone. Select utensils having flat bottoms large enough to cover the surface unit heating element. The use of undersized utensils will expose a portion of the heating element to direct contact and may result in ignition of clothing.
- Page 6 SAFETY AND WARNINGS Standard Requirements This induction cooktop generates and uses ISM frequency energy that heats cookware by using an electromagnetic field. It has been tested and complies with Part 18 of the FCC Rules for ISM equipment. This induction cooktop meets the FCC requirements to minimize interference with other devices in residential installation.
-
Page 7: Components Required
COMPONENTS REQUIRED Not supplied Silicone gun Ducting* Phillips screwdriver Masking tape Level Duct tape Box cutter Black installations: Black, matte finish silicone rated Router to 210°F (100°C) or above** Hex key Grey installations: Grey, matte finish silicone rated Spanner to 210°F (100°C) or above*** *Ducting must be purchased separately. - Page 8 ACCESSING YOUR PRODUCT SPECIFICATIONS For full product, cabinetry and service specifications, refer to the Planning Guide. To access the Planning Guide, scan the QR code or visit fisherpaykel.com/specify. Search by appliance type, product name or model code. Sample configuration...
- Page 9 UNPACK ALL PRODUCTS 1. Ensure all products and accessories are present. 2. Carefully remove products from cartons. Set aside on a protected surface. Dispose of packaging responsibly. 3. Test electrical connections of all products before proceeding with installation.
- Page 10 INSTALL IN CUTOUT 1. Gently lower the first product into the cutout. 2. Align the rear of the joining bracket to the back edge of the cutout and slot into place.. 3. Fit cover onto joining bracket before sliding it under the adjacent product.
- Page 11 INSTALL IN CUTOUT 4. Gently lower additional products and joining strips into cutout as required.
- Page 12 ALIGN PRODUCTS 1. Slot the T spacers between the products. Adjust positioning to ensure even spacing between products is achieved. 2. Flush installations: Place the shims around the outer edges of the cutout. Adjust positioning to ensure even spacing around the product set is achieved.
- Page 13 SECURE TO CUTOUT 1. Fit the securing brackets to the base of each cooktop. A minimum of two brackets per cooktop is recommended. 2. Tighten all clamp screws to secure the cooktops to the cutout and joiner strips.
-
Page 14: Connect Power
CONNECT POWER Before connecting to the mains power supply check that: The domestic wiring system is suitable for the power drawn by the cooktop. The voltage corresponds to the value given on the rating plate. The power supply cable sections can withstand the load specified on the rating plate. Refer to the Planning Guide for full service information. - Page 15 LINK PRODUCTS 1. Link each product to the adjacent product using the supplied communication cables. Ensure 8-pin plugs are only connected to 8-pin sockets and 6-pin plugs connected to 6-pin sockets. 2. Ensure all cables click into place and are routed away from cooktop exhausts.
- Page 16 SEAL PRODUCTS INTO CAVITY (FLUSH INSTALLATIONS) Some silicone products may cause discoloration of the glass, in most cases this will fade as the silicone cures. Avoid applying too much silicon during installation. 1. Mask the area to be siliconed ensuring all products and the countertop are protected.
-
Page 17: Installer Checklist
INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER GENERAL … Specified clearances have been maintained. … Products are level – front to back and side to side. … All packaging materials have been removed. … There is constant flow of cool air from the cabinetry to the base of the products. …... - Page 18 FISHERPAYKEL.COM © Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue.