Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sinclair ASDH-96AI
Summary of Contents for Sinclair ASDH-96AI
- Page 1 INSTALLATION MANUAL HIGH STATIC PRESSURE DUCT SERIE ASDH-96AI...
- Page 2 “Original instructions” IMPORTANT NOTE: Read this manual ca r efully befo r e installing or operating your new air conditioning unit. Make sure to save this manual for future reference.
-
Page 3: Table Of Contents
CONTENTS PAGE indoor unit, and direct the transmitting part of the remote control- ler to the receiver of the indoor unit. PRECAUTIONS..................1 The remote controller should be over 1m away from the ACCESSORIES ..................2 television or sound box. INSTALLATING INDOOR UNIT ...............2 Do not place the remote controller at a moist place, near the INSTALLATING OUTDOOR UNIT............4 heat sources such as stove, or expose it directly in the sunlight. -
Page 4: Accessories
13) Flare tool The site contains mineral oils such as cutting lubricant. 14) Pipe bender Seaside where the air contains much salt. 15) Level vial Hotpring area where corrosive gases exist, e.g., sulfide gas. 16) Metal saw Factories where the supply voltage fluctuates seriously. 17) Gauge manifold (Charge hose:R410A special requirement) Inside a car or cabin. - Page 5 3. INSTALLATING INDOOR UNIT Fix the pendant bolts firmly and reliably in light of the specific situation. 3.1 Installation Space（Unit:mm） Installation of the pendant bolt in different environments. Ensure enough space required for installation and maintenance. A. Wooden structure Put rectanglar sticks across the beams, and set pendant bolts. Wooden span Beam Maintenance space...
-
Page 6: Installating Outdoor Unit
3.6 Dimension（Unit:mm） and sound insulation devices, especially in the noise-sensitive spaces such as meeting rooms. ASDH-96AI For connection of the flange plane, use non-flammable canvas adapter to prevent transmission of vibration. For its size, see the indoor unit outline diagram. Use M6X20 screws (configured on site) for connection. - Page 7 Lifting hook Hoisting rope (belt) In the lifting process, without removal of cartons and other packaging to avoid damage to the product appearance. Single unit installation (Wall or obstacle) Center of gravity Air inlet >300 Maintain the electric As shown illustrating the rope must wire and pipeline pass through the inside of the circle two wooden support stakes, to avoid...
- Page 8 The indoor and outdoor connecting pipe interface and power NOTE line outlet Vavious piping and viring patterns can be selected,such as out from All the pictures in this manual are for explanation purpose only. the front ,the back the side ,and undersurface, etc.(The follow display They may be slightly different from the air conditioner you the locations of several piping and wiring knock-off interfaces) purchased(depend on model).The actual shape shall prevail.
- Page 9 4.12 Air Purge with Vacuum Pump Using vacuum pump to do the vacuum,never using refrigerant to Model Gas side Liquid side expel the air. ASDH-96AI (Indoor) 25.4mm 9.5mm Vacuuming should be done from both liquid side and gas side simultaneously. 25.4mm 9.5mm...
-
Page 10: Electric Connection
4.14 Schematic Diagram Of Connection b. Leakage detection alarm device linked with the mechanical ventilation device Between Indoor Unit And Outdoor Unit Signal wire Indoor unit a. Ventilation orifice part Gas-side connective pipe (The leakage detection alarm device should be installed at the place of system vulnerable to retention of the refrigerant) Fig.4-16... -
Page 11: Electric Wire Diagram
Specifications of power supply ASDH-96AI ASDH-96AI Model Power Switch capacity of the main 16/16 40/40 power suppliy/fuse(A) Indoor unit power cable(mm 3×2.5 mm includes grounded wire 5×6.0 mm Indoor Unit /Outdoor 3-core shielded wire Unit Signal Wire (mm 3X0.75 (Weak electric signal) The power cord type designation is H05RN-R or above/H07RN-F. -
Page 12: Setting Static Pressure
8. STATIC-CURVE heavy, it is necessary that two persons do it together. ASDH-96AI 9.1 Steps to remove the fan motor assembly Static curve (ENC2) 0 1) Remove the screws around the base of air conditioner till the base can be removed. - Page 13 9.2 Steps to install the fan motor assembly 1) Lift the fan motor assembly; make the edges of fan motor assembly touch the guide rails. It needs to two persons. (Fig.9-7) 2) Hold the bottom of the assembly, and then push it up along the guide rails.
-
Page 14: Construction And Ventilation Pipeline Design Scheme
Fig.9-12 10. CONSTRUCTION AND VENTILATION PIPELINE DESIGN SCHEME Examples of construction and ventilation pipeline design scheme(Flowering hidden series) Warehouse Document reference room Computer room Meeting room Office Office Construction and ventilation pipeline design scheme Kitchen Hall Meeting Manager room Retiring room office Document room... -
Page 15: Trial Run
11. TRIAL RUN Indoor unit Check whether the switch of the remote controller or wire controller is normal. Check whether the functional keys of the remote controller or wire controller are normal. CAUTION Check whether the indoor temperature conditioning is normal. Perform the trial run only after the outdoor unit has been powered on for over 12 hours. - Page 16 SINCLAIR CORPORATION Ltd. 1-4 Argyll St. London W1F 7LD Great Britain www.sinclair-world.com This product was manufactured in China (Made in China). REPRESENTATIVE SINCLAIR EUROPE spol. s r.o. Purkynova 45 612 00 Brno Czech Republic TECHNICAL SUPPORT NEPA spol. s r.o. Purkynova 45...