Table of Contents
Advertisement
Phase 1:
programming the overhead keypad
1. Make sure your vehicle is wit hin operating
range of the remote contro lled garage
door opener .
2. Set the parking brake
q
A
in General in-
formation on page 90 .
3 . Turn the ignition on . Do not start the en-
gine!
4.
Press and hold the two outs ide Home-
Link® buttons
(D
and @ for approxi-
mately 20 seconds until indicator light @
c:!;>
fig. 95
begins to flash. Then release
both buttons. Do not ho ld the buttons for
longer than 30 seconds .
.,. This procedure only needs to be performed
once. It erases the factory-set default codes
and does not have to be repeated to pro -
gram addit ional remote controls .
S. Press and hold the Home Link® button
(D,
®
or @ until t he indicator light @
starts flashing
slowly .
Release the bu tt on.
.,. The system will remain in programming
mode for 5 minutes . Co to the front of the
vehicle and proceed with phase 2.
Phase 2:
programming the bumper mounted trans
mitter
6.
Hold the
original remote control
at a dis-
tance between 0 - 6 in. (0- 15 cm) from the
bumper below the appropriate headlight
for your vehicle ¢
fig . 96
(use the shortest
distance possible) .
7 . Aim the remote contr ol just below the
driver side head light.
8 . Press and hold the activation button on
the remote contro l.
.,. May be different in Canada. If so, press and
re-press (cycle) the act ivation button on your
remote control every two seconds.
9 . The emergency flashers will flash three
times (after about 15-60 seconds) when
the programm ing is successful. Release
the button on the remote control.
.,. To program more devices, repeat steps 4 to
9.
Homelin
k®
91
10. Press and hold the trained Homelink ®
button and observe the indicator light @
q fig. 95.
.,. If the ind icator light is solid/continuous,
programm ing is complete and your device
should activate when you press and release
the tra ined Homelink ® button .
.,. If the ind icator light blinks rapidly for 2 sec-
onds and is then a solid/continuous
light,
proceed with phase 3 to program a roll ing
code device.
Phase 3: rolling code programming
.,. A second person on a ladder who can safely
reach the garage door opener motor is rec-
ommended .
11. Loca t e the "learn" button on the garage
door opener motor (refer to the operating
instructions for the opener, as the loca-
tion of t his button may vary by manufac-
turer) .
12 . Press and release the learn button on the
garage door opener motor .
.,. Note: once the button is pressed, there are
30 seconds in wh ich to init iate the next
step.
13. On the Homelink ® keypad inside the vehi-
cle, firmly press and hold the Homel ink®
button previously programmed in phases
1 and 2 for two seconds and release . Re-
peat this sequence twice.
.,. Some vehicles may require the press/hold/
release sequence up to three times to com-
plete the train ing process .
.,. Homelink ® should now activate your rolling
code equipped device.
If the 5 m inute time limit is exceeded, the
emergency flashers will flash one time to in-
dicate that the process has been term inated .
In this case, repeat steps 4 through 9.
If the emergency flashers do not flash
three
times (after about lS - 60 seconds), program-
ming was not successful. In this case, repeat
steps 4 through 9 .
Remote contro l units for garage door openers
in Canada are set to stop transmitting
radio
frequency signals after two seconds . This t ime
Ill-
Advertisement
Table of Contents
