Troubleshooting; Environmental Protection; Technical Specifications - Metabo SCV 18 LTX BL 1.6 Instructions Manual

en ENGLISH
- Re-tighten the screw (13) with enclosed Allen key
2 mm.
Bottom blade:
- Unscrew the screw (14).
- Remove the blade (12) with enclosed Allen key 2
mm, rotate 90° and insert again.
- Adjust the distance between the blades and
secure the blade (12) again enclosed Allen key 2
mm

9. Troubleshooting

Restart protection
The machine does not start, although it is switched
on. Restart protection is active. The machine will not
start if the battery pack is inserted while the machine
is on. Switch the machine off and back on again.
Overload protection
Electronic overload protection with integral
temperature monitor protects the machine and the
battery pack. If the temperature at the motor or
electronics is too high, the tool will switch off. Leave
the tool to cool down. Once the machine runs again,
let the machine run idle so that it cools down faster.
10. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
Battery packs with different capacities:
Best.-Nr.: .................. 625596000 2,0 Ah (LiHD)
Best.-Nr.: .................. 625367000 4,0 Ah (LiHD)
etc.
Chargers:
Best.-Nr.: 627044000 ASC 55
Best.-Nr.: 627378000 ASC 145
etc.
For a complete range of accessories, see
www.metabo.com or the main catalogue.
11. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

12. Environmental Protection

The sanding dust generated may contain
hazardous materials: do not dispose of with the
10
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.

13. Technical Specifications

Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U = Voltage of battery pack
B = Maximum sheet thickness (sheet steel)
St
B = Maximum sheet thickness (aluminium)
Al
h = Stroke rate at idle speed
0
h = Stroke rate at rated load
1
r = Smallest curve radius
min
m = Weight without mains cable
Measured values determined in conformity with
EN 62841.
Permitted ambient temperature during operation:
-20 °C (-4°F) to 50 °C (120°F) (limited performance
with temperatures below 0 °C (32°F)). Permitted
ambient temperature for storage: 0 °C (32°F) to
30 °C (86°F).
Direct current (cordless machines)
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a = Typical estimated acceleration
h
in the hand/arm area
(cutting sheet metal)
K = Uncertainty (vibration)
h
Typical A-effective perceived sound levels:
L = Sound pressure level
pA
L = Acoustic power level
WA
K , K = Uncertainty
pA WA
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!