Reset Features; Alert Priority; Compass Calibration Set-Up - Whistler Total Band Protection XTR-690SE Owner's Manual

OPERATION

Alert Priority

When two or more signals are received at the
same time, the alert priority is:
1. Laser 2. Speed Radar 3. Safety Radar
Example: If X band is alerting, then suddenly a
laser signal is detected, the laser warning will
override the X band alert.

Compass Calibration Set-up

The unit must be calibrated in order for the
compass to provide accurate headings. To
calibrate the unit, perform the following
procedure:
1 1 . . Mount the unit level in the center of the
vehicle's windshield. Make sure there are no
magnetic sources near the detector
(i.e., speaker) .
2 2 . Select a large clear area (parking lot or field)
without any power lines.
3 3 . Press the Menu button until display shows
C C A A L L M M O O D D E E . Then press the Dark and Quiet buttons
simultaneously. The display shows (scrolling):
4 4 . If calibration does not automatically finish, press
the Dark and Quiet buttons simultaneously to
complete calibration. The unit will beep twice and
display shows, for example:
Note: In Combo Mode, an "H H " or "C C " will be
shown to indicate mode of operation.
Important: If unit mounting is relocated in the
vehicle, (i.e., visor to windshield mounting or
dash mounting), or if the unit is moved to
another vehicle, you must recalibrate the
compass.
15
OPERATION

Reset Features

All user features can be reset to factory settings.
•Unplug the Power Cord from the unit.
•Press and hold the Power and Quiet buttons.
•Plug the Power Cord into the unit.
•Wait for 2 beeps.
•Release the Power and Quiet buttons.
Unit is now reset to the following features
and settings.
Default factory settings are:
1. S1: (For Intellicord ® ) Power ON or OFF.
2. S2: (For Intellicord ® ) Quiet feature.
3. Combo Mode.
4. HIGHWAY Mode.
5. Dim/Dark Mode to full illumination of display.
6. Auto Quiet Mode OFF.
7. Safety Radar OFF.
8. Vehicle Battery Saver ON/3hrs.
9. Full Power Up sequence.
10. Default TONE 3.
11. All Bands ON.
12. Laser ON.
13. POP ON.
14. Voice ON.
15. LED Periscopes to BLNK.
16. Filter Mode.
Intellicord ® Ready
Using Whistler's optional Intellicord
allows some models to control the detector's
features such as Power On/Off, City Modes,
Dim/Dark, and Quiet/Auto Quiet with a simple
press of the button on the Power Cable. Two
features can be controlled: one by a short press of
the button, and the second by a long press of the
button. Option Mode allows the user to program
the feature assignments.
16
Whistler has two new exciting features that will assist
the driving enthusiast to further identify threats from
laser and Ka band radar guns.
Ka RSID (Ka Radar Signal IDentifier)
Identify the difference between the likelihood of a Ka
threat vs. the likelihood of a Ka false from another
source (possible radar detector).
feature will educate you to the common Ka speed
radar guns by displaying the nominal police radar
frequencies of 33.8GHz / 34.0GHz / 34.3GHz /
34.7GHz / 35.5GHz. The Ka alerts that do not fall into
the common Ka speed radar windows will be reported
only as Ka.
Note:
This product is not a frequency counter. The
unit will categorize the received Ka signal and select
the appropriate information. Treat every Ka alert with
caution.
LSID (Laser Signal IDentifier)
Identify the Laser gun's pulse rate or PPS (Pulses Per
Second) that is transmitted by the speed laser gun.
LSID may also be used to identify other forms of laser
sources such as LACC (Laser Assisted Cruise Control)
systems found in some high end vehicles.
If the Laser PPS information displayed is due to
another source such as local airports or LACC, LSID
allows you to Lock Out this rate from giving you the
continuous audio alert during this and any new
encounter of the same rate. To Lock Out a PPS, press
the Quiet button during the Laser alert. This will
place an * on the screen beside the PPS rate and
Lock Out this signature ID. Any new encounter with
® Power Cable
the same Laser Signature ID will provide the display
information and two quick beeps.
Note: Common Laser PPS rates used in the USA are
100 / 125 / 130 / 200 / 238 / 380Hz. Other Laser PPS
rates used outside the USA include 600Hz.
Caution:
Do not lock out a PPS rate if it is close to
known speed laser guns.
OPERATION
The Ka RSID
17