Advertisement
Quick Links
Advertisement
Related Manuals for NCR 7360-K068
Summary of Contents for NCR 7360-K068
- Page 1 Kit Instructions Tri-Light/Lane Light with Camera Assembly and Lane Light Label 7360-K068 Issue C...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Software screen images are representative, and in some cases, may not match a customer’s installed software exactly.
- Page 3 Revision Record Issue Date Remarks Nov 2019 First Issue Jun 2020 Updated Username from Admin to admin. Dec 2021 Added Routing Tri-Light/Lane Light Cable page 22.
- Page 4 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label This publication provides procedures for installing a Tri-Light/Lane Light with Camera Assembly and Lane Light Label to an NCR FastLane SelfServ™ Checkout (7360) unit. Kit Contents Part Number Description 497-0526847 Kit - Tri-light with IP Camera and Label - Preferred Offer...
- Page 5 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label Part Number Description 497-0524107 Assembly - Tri-Light/Lane Light with Camera 006-8624498 Screw - M4 x 0.7 mm x 8 mm, flat head, stainless 497-0521720 R6L Lane Light Graphics Label - "Fastlane"...
- Page 6 Lane Light Label Installation Procedure To install the Tri-Light/Lane Light with Camera assembly, follow these steps: Note: Ensure that the NCR Customer Helpdesk is informed when the Tri-Light/Lane Light with Camera is installed in the store. 1. Do the following, if necessary: •...
- Page 7 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 6. Access the camera view by doing the following: a. Open a web browser. b. Enter the IP Address of the network camera in the address bar and press Enter to access login interface.
- Page 8 Right-hand (RH) orientation. For more information on setting the camera parameters, refer to Hikvision Network Camera User Manual. Note: Ensure that the NCR Customer Helpdesk is informed when the Tri-Light/Lane Light with Camera is installed in the store.
- Page 9 Removing the Tri-Light/Lane Light (R6) To remove the Tri-Light/Lane Light assembly, follow these steps: 1. Turn off the NCR SelfServ Checkout software and hardware systems. For more information, refer to "General Operational Procedures" section of NCR SelfServ™ Checkout (7360) Hardware Service Guide (B005–0000–2378).
- Page 10 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 3. Lift the Tri-Light/Lane Light assembly and then disconnect the cables. Tip: Mark all cables as to where they are connected to quickly determine the corresponding port when reconnecting the cables.
- Page 11 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label Removing Tri-Light/Lane Light Pole To remove the Tri-Light/Lane Light Pole, follow these steps: 1. Insert key in lock on the back of tower and then turn counterclockwise to unlock the terminal.
- Page 12 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 3. Remove the Scanner/Scale to access the screws that secure the Tri-Light/Lane Light Pole. 4. Remove the two (2) screws securing the Tri-Light/Lane Light Pole to the Tower Frame duct.
- Page 13 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label Installing Lane Light Label To install the label on each side of the Lane Light, follow these steps: 1. Remove the Tri-Light/Lane Light assembly, if necessary. 2. Wipe any dust or dirt on the surface of both sides of the Lane Light.
- Page 14 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 4. Depending on the type of Lane Light label, do either of the following: • Position the label on the Lane Light. Ensure that the label is flush with the front edge of the Lane Light, as shown in the image below.
- Page 15 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 5. Hold half of the label in place while peeling off the protective film from the other half of the label and then attach the label on the Lane Light, as shown in the image below.
- Page 16 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label Installing Tri–Light/Lane Light Pole To install the Tri-Light/Lane Light pole, follow these steps: 1. Remove the existing Tri-Light/Lane Light Pole, if necessary. For more information, refer to Removing Tri-Light/Lane Light Pole on page 8.
- Page 17 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 4. Insert the Tri-Light/Lane Light cable through the opening in the side of Tri- Light/Lane Light pole and route it out the top of the pole. Note: For the Tri-Light/Lane Light assembly without a camera, only the Tri- Light/Lane Light cable extender exist in the assembly.
- Page 18 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 5. Route the cables coming out of the unit so they align with the grooves and carefully insert the pole into the tower. 6. Secure the pole to the tower with two (2) screws.
- Page 19 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 7. Insert the excess cables into the opening on the Tri-Light/Lane Light pole so that the cables will not interfere with any outer items.
- Page 20 Installing Tri-Light/Lane Light with Camera Assembly To install the Tri–Light/Lane Light assembly, follow these steps: Note: Ensure that the NCR Customer Helpdesk is informed when the Tri-Light/Lane Light with Camera is installed in the store. 1. Remove the existing Tri–Light/Lane Light assembly, if necessary. For more...
- Page 21 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 3. Connect the Tri–Light/Lane Light with Camera Assembly cables.
- Page 22 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 4. Install three (3) cable ties on each side of the power connector and on the Ethernet cable to provide strain relief as shown in the image below. 5. Orient the Tri-Light/Lane Light assembly so that the Lane Light faces the front of the...
- Page 23 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 6. Insert the Tri–Light/Lane Light assembly into the Tri–Light/Lane Light pole. Ensure that the pole holes are aligned. Tip: To easily insert the cables with connectors through the pole, insert first the LAN cable followed by the Power cable, and then the Tri–Light/Lane Light...
- Page 24 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 7. Route and connect the Tri-Light/Lane Light and Power cables to the corresponding I/O Box port destinations: Note: For more information on routing the cables, refer to Routing Tri-Light/Lane Light Cable on the next page.
- Page 25 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label Routing Tri-Light/Lane Light Cable To route the Terminal Display cables in the Full Recycling (Fixed) unit, follow these steps: 1. Do the following: a. From the Tower Frame pole duct, route the Tri-Light/Lane Light cable down through the built-in hooks inside the Tower Frame.
- Page 26 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 2. From the corner cable access hole, route the cable down the Core Cabinet wall and connect to the I/O Box (Tri-Light/Lane Light port). Use cable ties to secure the cable on bridge lances.
- Page 27 Before configuring the camera settings, do the following: A. Obtain the IP address settings of the removed camera. This will be used to set the IP address of the new Camera. For more information, contact an NCR Representative or the Retailer's Help Desk.
- Page 28 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 2. Select Refresh to update the devices listed and their corresponding information. 3. Modify the network parameters by the doing the following, if necessary: a. Select the camera to modify by checking the check box.
- Page 29 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label Installing SADP Tool The Search Active Devices Protocol (SADP) is an online device search tool that allows users to search and to modify network information of online devices. For more...
- Page 30 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 4. Select Next. The installation window shows the default destination folder. 5. Select Change to enter a different destination from the default destination folder, if necessary.
- Page 31 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 6. Select Next throughout the process to choose all default settings until the window notifies that installation is complete. A setup window for Win10Pcap appears once SADP installation is completed.
- Page 32 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 7. Select Next. The installation window shows the default destination folder. 8. Select Change to enter a different destination from the default destination location, if necessary.
- Page 33 7360-K068 Tri-Light/Lane Light with Camera Assembly and Lane Light Label 9. Select Next to continue. The Windows Security Alert appears. 10. Select Next to proceed with the installation. The SADP Tool icon appears on the desktop once installation is completed.