Advertisement

Quick Links

LT2216CMA2
532 43 32-00 Rev. 1
Instruction manual
Please read these instructions care ful ly and
make sure you understand them before using
this machine.
Anleitungshandbuch
Bitte lesen Sie diese Anleitungen sorgfältig
durch und vergewissern Sie sich, daß Sie
diese verstehen, bevor Sie die Maschine in
Betrieb nehmen.
Manuel d'instructions
Merci de lire trés attentivement le manuel
d'instructions. Assurez-vous d'avoir tout com-
pris avant d'utiliser ce tracteur.
Manual de las instrucciones
Por favor lea cuidadosamente y comprenda
estas intrucciones antes de usar esta ma-
quina.
Manuale di istruzioni
Prima di utilizzare la macchina leggete queste
istruzioni con attenzione ed accertatevi di
averle comprese bene.
Instructieboekje
Lees deze instructies aandachtig en zorg dat u
ze begrijpt voordat u deze ma chine gebruikt.

Advertisement

Table of Contents
loading

Summary of Contents for Jonsered LT2216CMA2

  • Page 1 Manuale di istruzioni Prima di utilizzare la macchina leggete queste istruzioni con attenzione ed accertatevi di averle comprese bene. Instructieboekje Lees deze instructies aandachtig en zorg dat u ze begrijpt voordat u deze ma chine gebruikt. LT2216CMA2 532 43 32-00 Rev. 1...
  • Page 2 Safety rules. Montaje. Sicherheitsvorschriften. Montaggio. Règles de sécurité. Montering. Assembly. Descripción del funcionamiento. Zusammenbau. Funzionamento. Montage. Beschrijving van functies. Functional description. Antes del arranque. Funktionsbeschreibung. Prima dell’avviamento. Description du fonctionnement. Maatregelen vóór het starten. Before starting. Conducción. Maßnahmen vor dem Anlassen. Guida.
  • Page 3: Safety Rules

    1. Safety Rules Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. III. OPERATION I. TRAINING •...
  • Page 4: Maintenance And Storage

    • Stop the engine and disengage drive to attachment - before refueling; - before removing the grass catcher; - before making height adjustment unless ad just ment can be made from the op er a tor’s position. • Reduce the throttle setting during engine run-out and, if the engine is provided with a shut-off valve, turn the fuel off at the conclusion of mowing.
  • Page 5 1. Sicherheitsvorschriften Regeln für die sichere Bedienung von Rasentraktoren WICHTIG: DIESE MÄHMASCHINE KANN HÄNDE UND FÜSSE ABTRENNEN UND GEGENSTÄNDE MIT HOHER GESCHWINDIGKEIT SCHLEUDERN. NICHTBEACHTUNG DER FOLGENDEN SICHERHEITSVORSCHRIFTEN KÖNNTE SCHWERE ODER TÖDLICHE VERLETZUNGEN ZUR FOLGE HABEN. I. SCHULUNG • Vor dem Gebrauch immer mit einer Sichtprüfung sicherstel- •...
  • Page 6: Wartung Und Lagerung

    • Vor dem Verlassen der Bedienungsstation: - Die Zapfwelle abstellen und alle Anbaugeräte absen- ken. - In Leerlauf schalten und die Feststellbremse einle- gen. - Den Motor abstellen und den Zündschlüssel abzie- hen. • Alle Anbaugeräte-Antriebe ausschalten, den Motor abstel- len und das (die) Zündkerzenkabel abziehen bzw.
  • Page 7: Règles De Sécurité

    1. Règles de Sécurité Conseils pour l’utilisation en toute sécurité des tracteurs de pelouse ATTENTION: CE TRACTEUR DE PELOUSE EST CAPABLE D’AMPUTER MAINS OU PIEDS ET DE PROJETER DES OBJETS.L ’INOBSERVATION DES RÈGLES DE SÉCURITÉ CI-DESSOUS PEUT ÊTRE LA CAUSE DE BLESSURES SÉRIEUSES VOIRE MORTELLES.
  • Page 8: Entretien Et Entreposage

    • Débrayer les lames, arrêter le moteur, et débrancher le (s) fil (s) de (s) bougie (s) d’allumage ou retirer la clef de contact : - avant de retirer l’insert broyeur ou avant de retirer la goulotte d’éjection pour la nettoyer. - avant de contrôler, nettoyer ou travailler sur le carter de coupe, - avant de retirer un objet coincé...
  • Page 9: Reglas De Seguridad

    1. Reglas De Seguridad Prácticas de Operación Seguras para las Segadoras Conducibles IMPORTANTE: ESTA MAQUINA CORTADORA ES CAPAZ DE AMPUTAR LAS MANOS Y LOS PIES Y DE LANZAR OBJETOS. SI NO SE OBSERVAN LAS INSTRUCCIONES DE SEGURIDAD SIGUIENTES SE PUEDEN PRODUCIR LESIONES GRAVES O LA MUERTE.
  • Page 10: Mantenimiento Y Almacenamiento

    • Antes de dejar la posición del operador: - desenganche la fuerza motriz y baje los acceso- rios; - cambie a neutro y enganche el freno de estaciona- miento; - pare el motor y remueva la llave. • Desenganche la transmisión a los accesorios, pare el mo- tor, y desconecte el (los) cable (s) de la bujía o remueva la llave de ignición - antes de limpiar bloqueos o desatrancar del con-...
  • Page 11: Norme Antinfortunistiche

    1. Norme Antinfortunistiche Regole di sicurezza per trattorini da prato ATTENZIONE: QUESTO TRATTORINO TOSAERBA HA UNA POTENZA SUFFICIENTE AD AMPUTARE MANI E PIEDI E A SCAGLIARE OGGETTI. LA MANCATA OSSERVANZA DELLE SEGUENTI ISTRUZIONI ANTINFORTUNISTICHE POTREBBE CAUSARE LESIONI GRAVI E PERSINO IL DECESSO DELLA VITTIMA. •...
  • Page 12 • Disinnestare la trasmissione del moto agli accessori, spegnere il motore e scollegare i fili delle candele op- pure togliere la chiavetta di accensione: - prima di pulire eventuali intasamenti e pri ma di stasare lo scivolo; - prima di interventi o controlli sul tosaerba e prima delle operazioni di pulizia;...
  • Page 13 1. Veiligheidsregels Veilige bedieningsmethoden voor zittrekkers BELANGRIJK: DEZE MAAIMACHINE KAN HANDEN EN VOETEN AMPUTEREN EN VOORWERPEN WEGSLINGEREN. HET NIET OPVOLGEN VAN DEZE VEILIGHEIDSINSTRUCTIES KAN ERNSTIG OF DODELIJK LETSEL TOT GEVOLG HEBBEN. III. BEDIENING I. TRAINING • Laat de motor niet draaien in een besloten ruimte waar •...
  • Page 14: Onderhoud En Opslag

    LT2216CMA - als de machine abnormaal begint te trillen (onmid- dellijk controleren); - vor dem Entfernen von Verstopfungen aus dem Mähwerk oder dem Auswurf. 14.54/10.84 • Schakel de aandrijving naar de hulpstukken uit tijdens transport of als ze niet worden gebruikt. •...
  • Page 15 These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit.
  • Page 16 These symbols may appear on your machine or in the literature supplied with the product. Learn and understand their meaning. Diese Symbole finden Sie auf Ihrer Maschine oder in Unterlagen, die mit dem Produkt ausgehändigt wurden. Bitte machen Sie sich mit deren Bedeutung vertraut. Ces symboles peuvent figurer sur tracteur ou dans les publications fournies avec le produit.
  • Page 17 01738 GEFAHR AUGEN UNVER- ZU VERMEIDEN: SCHWEFELSÄURE ZÜGLICH MIT WASSER AUGEN SCHÜTZEN • FUNKEN KANN ERBLINDUNG AUSSPÜLEN. SOFORT EXPLOSIVE GASE ODER SCHWERE VERÄT- ÄRZTLICHE HILFE KÖNNEN ERBLINDUNG • FEUER ZUNGEN VERURSACHEN. AUFSUCHEN. UND KÖRPERVERLET- • RAUCHEN ZUNGEN VERURSAC- HEN. GEVAAR GEEN ZWAVELZUUR OGEN ONMIDDELLIJK...
  • Page 18: Steering Wheel

    2. Assembly. 2. Zusammenbau. 2. Montage. 2. Montaje 2. Montaggio. 2. Montering. Before the tractor can be used certain parts must be as - Antes de poder utilizar el tractor, hay que montar algunas sem bled, which for transportation reasons are enclosed in piezas que, por razones de transporte, van empaquetadas the packing.
  • Page 19 Empujar en el asiento para enganchar el bulón de la espalda en la ranura y empujar el asiento hacia la parte trasera del tractor. El asiento es ajustable individualmente en relación a los pedales del embrague y de freno. Ajustar el asiento en la posición correcta desplazándolo hacia adelante o atrás.
  • Page 20: Install Battery

    Install battery NOTE: If battery is put into service after month and year 1. Battery Cover 1. Tapador del acumulador indicated on label, charge battery for minimum of one hour 2. Cable Positive (+) 2. Cable positivo (+) at 6-10 amps. 3.
  • Page 21 WARNING: Positive terminal must be con nect ed first to prevent sparks from ac ci den tal grounding. Remove terminal caps and discard. Connect the red cable to + and then the black earth ca ble to -. Screw tight the cables.
  • Page 22 To install bagger com po nents to tractor 1. Support Bracket 2. Clevis Pin 10 x 17mm 3. 3/8 Lock Nut 4. 3/8 x 63,5mm Hex Bolt 5. 10,3mm (13/32") flat 1. Dis charge Chute washer 2. 3/8 Nut 6. Retainer Spring 3.
  • Page 23: Horizontal Adjustment

    To Assemble Bagger • Unfold bag by pivoting front bagger tube all the way forward and pressing the bottom vinyl binding onto the tube. • Inside the bag, install spreader bars and retainer springs onto pins on both sides of bag as shown. •...
  • Page 24 Installation der Aufhängung der Grasfangbox des Traktors 1. Strebe 2. Fixierfeder 10x17mm 3. Kontermutter 3/8 4. S e c h s k a n t b o l z e n 3/8 x 63,5mm 5. Flache Unterlegscheibe 1. Auswurfkanal 10,3mm (13/32) 2.
  • Page 25: Montage Der Grasfangbox

    Montage der Grasfangbox • Entfalten Sie den Beutel, indem Sie das vordere Staub- beutelrohr ganz nach vor klappen und die untere Vinyl- bindung an das Rohr drücken. • Setzen Sie dann im Beutel die Spreizstäbe und die Rück- haltefedern in die Zapfen an beiden Seiten des Beutels wie gezeigt ein.
  • Page 26 Assemblage des composants du collecteur 1. Bras support supérieur 2. Cheville de fixation 10x17mm 3. Ecrou frein 3/8 4. Vis H 3/8 x 63,5 5. Rondelle plate diam. 10,3 mm (13/32") 1. Goulotte d'éjection 6. Epingle 2. Ecrou 3/8 3. Rondelle plate •...
  • Page 27 Pour assembler le collecteur • Déplier le sac en faisant basculer complètement vers l’avant le tube antérieur de l’ensacheuse et en poussant la bordure inférieure en vinyle sur le tube. • Dans le sac, placer les entretoises et les ressorts de retenue sur les goupilles des deux côtés du sac, de la façon illustrée.
  • Page 28 Para montar los componentes del contenedor para costales al tractor 1. Consola portadora 2. Resorte fijador 10x17mm 3. Contratuerca 3/8 4. 3/8x63,5mm arandelas planas 5. Arandela plana 10,3mm (13/32î) 1. Descarga de adaptarse 6. Clavija hendida 2. Tuercas de 3/8 3.
  • Page 29 Para montar el contenedor • Desplegar la bolsa pivoteando el tubo frontal del saco completamente hacia adelante y presionado la atadura de vinilo del fondo hacia el tubo. • En el interior de la bolsa, instalar las barras extendedoras y los resortes de retención en las clavijas en ambos lados de la bolsa como mostrado.
  • Page 30 Per montare i componenti del cesto di raccolta 1. Staffa di supporto 2. Perno di fissaggio 10x17mm 3. Dadi 3/8 1. Convogliatore di scarico 4. Bullone a testa esagonale (3/8 x 63,5mm) 2. Dadi 3/8 5. Rondella piatta 3. Rondella Piatta 6.
  • Page 31 Per montare il cesto di raccolta: • Svolgere il sacchetto ruotando completamente in avanti il tubo anteriore dell’insaccatrice e premendo la parte inferiore in vinile sul tubo. • All’interno del sacchetto, installare le barre distanziatrici e le molle di tenuta sui perni di entrambi i lati del sacchetto, come mostrato in figura.
  • Page 32 Hetmonteren van componenten van de grascontainer op de trekker 1. Stennijzer 2. Vorkbout 10x17mm 3. 3/8 borgmoer 4. 3/8 Zeskantbout 5. Vlakke sluitring 10,3 mm (13.32") 6. Sluitveer 1. Afvoertrechter 2. 3/8 borgmoer 3. Vlakke sluitring • Bevestig de twee bovenste steunbeugels door de achter- •...
  • Page 33 De grascontainer monteren • Vouw de zak open door de voorste zakkenvulbuis helemaal naar voren te draaien en de onderste band van vinyl op de buis te drukken. • Installeer in de zak de spreiders en de borgveren op de pinnen aan de beide zijden van de zak, zoals op de afbeelding.
  • Page 34 1. Mango 1. Handle 2. Resorte fijador 2. Retainer Spring 3. Clavija 3. Pin 4. Tapon o tapa 4. Plug 1. Handgriff 1. Impugnatura 2. Fixierfeder 2. Coppiglia 3. Perno 3. Stift 4. Stöpsel 4. Kit Mulch ing 1. Poignée de l'insert 1.
  • Page 35 PARA AJUSTAR LAS RUEDAS CALIBRADORAS (si se incluyen) Las ruedas calibradoras están bien ajustadas cuando se encuentran un poco a distancia del terreno al mismo tiempo que la segadora esté a la altura de corte deseada. Entonces las ruedas calibradoras mantienen el conjunto segador en posición para prevenir el corte raspeo en casi todos los ter- renos.
  • Page 36 3. Functional description. 3. Funktionsbeschreibung. 3. Description du fonctionnement. 3. Descripción del funcionamiento. 3. Funzionamento. 3. Beschrijving van functies. 02997 Anordnung der Bedienungseinrichtungen Positioning of controls 1. Light Switch. 1. Lichtschalter. 2. Throttle 2. Gashebel. 3. Brake and clutch pedal. 3.
  • Page 37 02997 Comandi Emplacement des commandes 1. Interruttore luci. 1. Interrupteur de commande des phares 2. Acceleratore. 2. Commande des gaz (Accélérateur) 3. Pedale freno/frizione. 3. Pédale d'embrayage et de frein 4. Leva del cambio. 4. Levier de commande de la transmission hydrostatique 5.
  • Page 38 1. Light switch 1. Lichtschalter 1. Interrupteur des phares 1. Interruptor de alumbrado 1. Interruttore luci 1. Schakelaar verlichting 2. Throttle control The throttle control regulates the engine revs and thus the rotation speed of the blades. = Full speed = Idling speed 2.
  • Page 39 3. Brems- und Kupplungspedal Beim Vorwärtsdrücken des Pedals wird das Fahrzeug abge- bremst. Gleichzeitig wird der Motor ausgekuppelt und das Fahrzeug rollt aus. 3. Pédale d'embrayage et de frein En appuyant sur cette pédale, la transmission se débraye et le frein entre en action simultanément. 3.
  • Page 40 5. Commande d'embrayage et de débrayage du carter de coupe Pousser le levier vers l'avant et le verrouiller pour embrayer le carter de coupe. Les courroies d'entraînement seront alors en tension et les lames commenceront à tourner. Ramener le levier vers l'arrière pour débrayer le carter de coupe, les lames seront alors freinées par le frottement des patins de frein sur les poulies d'entraînement.
  • Page 41 ROS ON ROS ON START 7. Cerradura de encendido 7. Ignition Lock La llave de encendido puede hallarse en tres posiciones There are three different positions for the ignition key: diferentes: All electric current bro ken. Corriente eléctrica cortada ROS ON Reverse Operation System (ROS) connected ROS ON Sistema de Funcionamiento Atrás (ROS)
  • Page 42 8. Frein de stationnement Pour enclencher le frein de stationnement : 1. Enfoncer à fond la pédale d'embrayage/frein. 2. Relever vers le haut le levier du frein de stationnement et le maintenir dans cette po si tion. 3. Relâcher la pédale d'embrayage/frein. Relâcher le levier du frein de stationnement qui restera dans sa position verrouillée (en haut).
  • Page 43 10. Réglage de la hauteur de coupe Pour régler la hauteur de coupe, tirer vers l'arrière le levier de relevage du carter de coupe et faire tourner simultanément le bouton moleté du système de réglage de la hauteur de coupe. Pour augmenter la hauteur de coupe, faire tourner le bouton moleté...
  • Page 44 14. Service Reminder/Hourmeter Indicates when service is required for the engine and mower. 14. Service Reminder/Studenzähler Zeigt an, wann der Motor und der Rasenmäher gewartet werden müssen. 14. Rappel Entetien/Compteur Horaire Indique à quel moment exécuter les opérations d’entretien du 03013 moteur et de la tondeuse.
  • Page 45 4. Before starting. 4. Maßnah men vor dem Anlassen. 4. Avant de démarrer. 4. Antes del arranque. 4. Prima dell’avviamento. 4. Maatregelen vóór het starten. Filling up Reposición de combustible The en gine should be run of pure (not oil mixed) un lead ed El motor ha de funcionar con gasolina pura (sin mezcia de petrol.
  • Page 46: Pressione Pneumatici

    Oil level Nivel de aceite The combined oil refilling cap and the oil stick is ac ces si ble La tapa combinada para el llenado de aceite y para la varilla when the bonnet is lifted for wards. The oil level in the engine de nivel queda accesible después de haber levantado hacia should be checked before each run.
  • Page 47 5. Driving. 5. Betrieb. 5. Conduite. 5. Conducción. 5. Guida. 5. Rijden. Démarrage du moteur S’assurer que le carter de coupe est en position de transport (en position supérieure) et que le levier pour l’embrayage/dé- brayage du carte de coupe est en position de débrayage. 01842 Arranque del motor Asegúrese de que el equipo de corte está...
  • Page 48 Bei warmem Motor: Gashebel in die Vollgasstellung " " schieben. Si le moteur est chaud: pousser la commande des gaz à mi- distance de sa position d'accélération maximale. " ". Moter caliente: Empuje el acelerador hasta la mitad de su recorrido hacia la posición de plenos gases "...
  • Page 49 IMPORTANT! COLD STARTING FOR HYDRO • Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position COLD STARTING FOR HYDRO (BE LOW 40°F[4°C]) - AF TER and hold for five (5) seconds. Repeat this pro ce dure three STARTING ENGINE AND BEFORE DRIVING, LET TRANS- (3) times.
  • Page 50 SPURGO DELLA TRASMISSIONE • Débrayer la transmission en plaçant la commande de roue libre sur sa position de marche en roue libre (Se Per assicurare il buon funzionamento prestazionale del trat- référer à la section "TRANSPORT" de ce livret). tore, si raccomanda di spurgare la trasmissione prima di met- •...
  • Page 51: Betrieb

    NOTE! NOTA! The machine is equipped with a safety switch which La máquina tiene un interruptor de seguridad que corta immediately breaks the current to the en gine if the la corriente al motor si el con duc tor sale del asiento con driver leaves the seat with en gine run ning and with the el motor en marcha y con la palanca de acoplamiento/ con nec tion/dis con nec tion le ver in position “connection”.Your...
  • Page 52 Engine "ON" (Normal Operating) ROS "ON" ROS "AN" Motor "AN" (Normalbetrieb) ROS "ON" Moteur "ON" (Fonctionnement normal) ROS "ON" Motor "ON" (Funcionamiento Normal) ROS "ON" Motore "ON" (Funzionamento normale) ROS "ON" Motor "ON" (normaal functioneren) Sécurité Marche Arrière (ROS) Reverse Operation System (ROS) Votre tracteur est équipé...
  • Page 53: Cutting Tips

    Sistema per operazioni in retromarcia (ROS) Cutting tips Il Vostro trattore possiede un Sistema per operazioni in re- • Clear the lawn from stones and other objects which can tromarcia (ROS). Qualsiasi tentativo da parte dell’operatore be thrown away by the blades. di guidare nella direzione opposta con la frizione abbassata comporterà...
  • Page 54 Conseils pour la tonte Consigli per il taglio dell’erba • Retirer de la pelouse, les pierres et autres objets qui • Pulire il prato da pietre e altri corpi estranei. pourraient être propulsés par les lames et devenir ainsi • Individuare ostacoli fissi.
  • Page 55 Pour vider le bac Votre tracteur est équipé d'une alarme sonore qui vous avertit lorsque le bac est plein. Pour arrêter l'alarme, débrayer les lames. • Amener le tracteur là ou vous souhaitez le décharger. • Mettre le levier de boîte de vitesses au point mort et tirer le frein à...
  • Page 56: To Convert Mower

    To convert mower • Installieren Sie den Auswurfkanal durch die Öffnung der hin- teren Platte des Traktors auf den Adapter des Mähdecks. (Converting to mulching or rear discharging will re quire the • Fixieren Sie den Kanal, indem Sie die beiden Haken in purchase of these ac ces so ries.) die dafür vorgesehenen Bohrungen einrasten lassen.
  • Page 57 Para cambiar el ajuste de la segadora Per lo scarico a terra • Mettere il piatto nella posizione piu' alta. (Un cambio de ajuste para no recoger la hierba o usarla tipo mulching requiere la compra de los mecanismosdispositivos • Togliere il cesto e il Kit Mulching siguientes) •...
  • Page 58 ATTENTION! • Ne jamais utiliser un tracteur sur des pentes excédant 15°. Les risques de renversement étant alors très importants. • Ne jamais rouler parallèlement à la pente du fait des risques de renversement. Toujours rouler perpendiculairement à la pente, aussi bien en montant, qu'en descendant. •...
  • Page 59: Abschalten Des Motors

    Switching off the engine Move the attachment clutch control to disengaged position. Move the throttle control between half and full speed (fast) position. Lift up the cutting unit and turn the ignition key to “STOP” position. Abschalten des Motors Stellen Sie die Steuerung der Anhängerkupplung auf aus- gekuppelt.
  • Page 60 6. Maintenance, adjustment. 6. Wartung (Instandhaltung), Einstel- lung. 6. Entretien, réglages. 6. Mantenimiento, ajuste. 6. Manutenzione. 6. Onderhoud, afstelling. WARNING! ADVERTENCIA! Before servicing the engine or cutting unit the fol low ing shall Antes de proceder a efectuar el servicio en el motor o en be carried out: el equipo de corte, hay que hacer lo siguiente: •...
  • Page 61 Engine hood • Raise hood. • Unsnap headlight wire connector. • Stand in front of tractor. Grasp hood at sides, tilt forward and lift off of tractor. • To reinstall, slide hood pivot brackets into slots in frame. • Reconnect headlight wire connector and close hood. Motorhaube •...
  • Page 62 Maintenance Mantenimiento NOTE: Periodic maintenance should be performed on a regular NOTA: El mantenimiento periódico ha de hacerse con regu- basis in order to keep your tractor in good running condition. laridad a fin de mantener el tractor en buen estado. WARNING: Disconnect spark plug wire to prevent ac ci den tal ADVERTENCIA: Antes de efectuar cualquier reparación, starting before attempting any repair, inspection, or main te nance.
  • Page 63: Olie Vervangen

    POUR CHANGER L ’HUILE • Sortez la rallonge de vidange d’huile en la glissant hors de sa position d’arrimage sur le boîtier du souffleur et déployez-la. • Pour ouvrir, tournez le capuchon dans le sens anti- horaire. • Après avoir vidangé toute l’huile, remettez le capuchon en place et fermez-le en tournant dans le sens horaire jusqu’à...
  • Page 64 SERVICE RECORD Fill in dates as you complete regular service Every 8 Every Every . Every . Every Needed hours 25 hours 50 hours 100 hours 200 hours • Change engine oil (without oil filter) ........... • Change engine oil (with oil filter) ................•...
  • Page 65 SCHEMA D'ENTRETIEN Consigner les dates d'intervention après chaque opération d'entretien. Selon les Toutes Toutes Toutes Toutes les Toutes les besoins les 8 H les 25 H les 50 H 100 H 200 H Vidange de l'huile moteur • (sans filtre à huile ..................
  • Page 66 DATI DI SERVIZIO Compilare ogni qualvolta si esegue un regolare servizio Necessità Ogni Ogni Ogni . Ogni Ogni 8 ore 25 ore 50 ore 100 ore 200 ore • Cambio dell'olio (Senza filtro dell’olio)..........• Cambio dell'olio (Con filtro dell’olio) ................ •...
  • Page 67 Operator Presence System and Reverse Opera- tion System (ROS) Be sure operator presence and reverse operation sys tems are work ing properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully de pressed, and the attachment clutch con trol is in the dis en gaged position.
  • Page 68 Sistema de Presencia Operador y Sistema de Funcionamiento Atrás (ROS) Asegurarse de que los sistemas de presencia operador y funcionamiento atrás funcionen adecuadamente. Si tu tractor no funciona como descrito, hay que reparar el problema inmediatamente. • El motor no tiene que arrancar hasta que le pedal del freno no esté...
  • Page 69 Blades Cuchillas The blades should be sharp to achieve best cutting results. Las cuchillas han de estar afiladas para proporcionar el mejor Sharpening can be carried out with a file or grinding disc. corte posible. El afilado puede hacerse con lima o muela. NOTE: It is very important that both blades are sharpened NOTA: Es muy importante que los dos lados de la cuchilla equally to avoid imbalance.
  • Page 70 5 Star pattern blade The center of this blade has a five (5) star pattern. The bolt that attaches this blade has normal Right Hand threads that loosens by turning ( ) counter-clock wise and tightens by turn ing ( ) clockwise. Messerbalkenbohrung mit fünfeckige Ausspar- Die Bohrung des Messerbalkens hat eine fünfeckige Ausspar- ung.
  • Page 71 Cuchilla de orificio-estrella de cinco puntas El centro de esta cuchilla se parece a una estrella de cinco (5) puntas. El tornillo que liga esta cuchilla es dextrogiro normal y se desentornilla en direcciûn opuesta a la vuelta de la aguja del reloj y se emperna dandole vueltas en la direcciûn de la aguja del reloj.
  • Page 72 For best results mower blades must be kept sharp. Re place Para alcanzar resultados mejores las cuchillas de la segadora bent or damaged blades. hay que mantenerlos afilados. sustituya las cuchillas torcidos y estropeados. BLADE REMOVAL C'MO DESMONTAR LAS CUCHILLAS •...
  • Page 73 Controlar el Freno To Check Brake Si el tractor requiere más de cinco (5) pies para pararse a la If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved sur- velocidad más alta en la marcha más alta en una superficie nivelada seca en hormigón o adoquinada, hay que reparar face, then brake must be serviced.
  • Page 74 Desmontaje de la unidad de corte Trabajar desde el lado derecho de la máquina. 1. Quitar después la correa de la polea del motor (1). 2. Quitar los dos resortes posteriores (2) y golpear con un martillo los muñones de eje hasta sacarlos. 3.
  • Page 75 Cambio de la correa propulsora del equipo de Replacement of drive belt for cutting unit corte 1. Dismantle the cutting unit as described previously. 1. Desmontar el equipo de corte del tractor. 2. Work off the belt from the unit's left pulley and then from the other wheels.
  • Page 76 01268 Adjustment of the cutting unit To achieve best cutting results the cutting unit’s front edge (B) A. In the direction of travel should be about 10 mm (0.375") low er than the back edge 1. Check that the air pressure is correct in all four tires. (A).
  • Page 77 00598 REGLAGE TRANSVERSAL • Relever le carter de coupe au maximum. • A partir du milieu de chaque extrémités latérales du carter de coupe, mesurer la distance du bord du carter par rap- “A” “A” port au sol . • La distance (A) doit être la même des deux côtés à...
  • Page 78 EINSTELLUNG DES STEUERKNÜPPELS DES SCHALTGETRIEBES Der Steuerknüppel wird von der Herstellerfirma im Werk vore- ingestellt und erfordert daher in der Regel keine weiteren Einstellungen. • Den vorne auf dem rechten Hinterrad befindlichen Ein- stellbolzen lösen und wieder leicht anziehen; • Den Motor anlassen und den Steuerknüppel verschieben, bis sich der Traktor weder vorwärts noch rückwärts be- wegt;...
  • Page 79 REGOLAZIONE DELLA LEVA DI COMANDO DEL MOVIMENTO DEL MECCANISMO DEL CAMBIO La leva di comando del movimento del meccanismo del cambio è stata impostata al momento della fabbricazione e non richiede pertanto ulteriori regolazioni. • Allentare il bullone di regolazione di fronte alla ruota posteriore destra;...
  • Page 80 Cambio de correa propulsora 1. Desmontar el equipo de corte del tractor. 2. Desmontar el limitador de movimientos del acoplamiento (1). 3. Aplicar el freno de estacionamiento y tirar hacia arriba de la correa para sacarla de la rueda libre (2), de la acoplamiento (3).
  • Page 81 ENFRIAMIENTO DEL TRANSEJE TRANSAXLE COOLING Las aletas de enfriamiento y el ventilador de la trans mi sión The fan and cooling fins of transmission should be kept clean tienen que mantenerse limpios para asegurar el enfriamiento to assure proper cooling. adecuado.
  • Page 82 WASCHANLAGEN-ÖFFNUNG DER ABDECKUNG Ihre Traktorabdeckung ist außen mit einer Waschanlagen-Öffnung ausgestattet, die Teil der Waschanlage für die Abdeckung ist. Sie sollte nach jedem Gebrauch eingesetzt werden. • Fahren Sie den Traktor auf eine ebene, saubere Stelle Ihres Rasens, möglichst nah an einen Wasserhahn, an den Sie Ihren Gartenschlauch anschließen können.
  • Page 83 BOCA DE LAVADO DE LA PLATAFORMA La plataforma del tractor cuenta con una boca de lavado en la superficie como parte del sistema de limpieza. Se debe utilizar tras cada uso. • Desplace el tractor a un punto nivelado y despejado del prado, cerca de un grifo al que pueda conectar la manguera.
  • Page 84 DEKREINIGINGSPOORT Het maaidek van uw trekker is aan de bovenkant uitgerust met een reinigingspoort als onderdeel van het dekreinigingssysteem. Dit systeem dient na elk gebruik van de maaier te worden gebruikt. • Rijd de trekker naar een vlakke, open plek op uw gazon, dicht genoeg bij een waterkraan om met de tuinslang te bereiken.
  • Page 85: Recordatorio Mantenimiento/Cuenta- Horas

    RECORDATORIO MANTENIMIENTO/CUENTA- SERVICE REMINDER/HOUR METER HORAS Service reminder shows the total number of hours the engine has run and flashes to indicate that the engine or mower needs El recordatorio del mantenimiento muestra el número total de servicing. When service is required, the service reminder will horas de funcionamiento del motor y parpadea para indicar flash for two hours.
  • Page 86 7. Troubleshooting. 7. Störungssuche. Engine will not start Motor springt nicht an 1. No fuel in fuel tank. 1. Kraftstoff fehlt im Kraftstofftank. 2. Defekte Zündkerze. 2. Plug defective. 3. Plug connection defective. 3. Defekter Zündkerzenanschluß. 4. Dirt in carburetor or fuel pipe. 4.
  • Page 87 7. Recherche des pannes. 7. Búsqueda de averías. El motor no arranca Le moteur ne démarre pas 1. No hay combustible en el depósito. 1. Manque de carburant dans le réservoir. 2. Bougie d'allumage défectueuse. 2. La bujía es errónea. 3.
  • Page 88 7. Ricerca guasti. 7. Het localiseren van fouten. Il motore non parte De motor start niet 1. Manca il carburante. 1. Er is geen benzine in de tank. 2. Difetto di candela. 2. De bougie is defect. 3. Collegamento della candela difettoso. 3.
  • Page 89 8. Storage. 8. Aufbewahrung. 8. Rangement. 8. Conservación. The following steps should be taken when mowing Suivre la procédure suivante une fois la saison termi- née: season is over: • Clean the entire machine, especially underneath the • En fin de saison, suivre la procédure suivante pour le cutting unit cover.
  • Page 90 8. Rismessaggio. 8. Stallen. Al termine della stagione effettuare i seguenti inter- Aan het einde van elk maaisezoen moeten de vol gen de venti: maatregelen worden genomen: • Pulire tutto il tagliaerba e particolarmente sotto il co per chio • Maak de hele machine schoon, in het bijzonder de bin- della falciatrice.
  • Page 92 Jonsered Motor AB, 07.15.10 BAD S-433 81 Partille, Sweden. Printed in U.S.A.

Table of Contents