MSI Optix G273 - Full HD WLED Gaming LCD Monitor Manual
Getting Started
This chapter provides you with the information on hardware setup procedures. While connecting devices, be careful in holding the devices and use a grounded wrist strap to avoid static electricity.
Package Contents
Monitor | Optix G273 |
Documentation | Quick Start Guide |
Registration Card |
Accessories | Stand with Screw(s) |
Stand Base with Screw(s) |
Power Adapter & Power Cord |
Cables | HDMI Cable (Optional) |
DisplayPort Cable (Optional) |
- Contact your place of purchase or local distributor if any of the items is damaged or missing.
- Package contents may vary by country.
- The included power cord is exclusively for this monitor and should not be used with other products.
OSD Setup
This chapter provides you with essential information on OSD Setup.
All information is subject to change without prior notice.
Navi Key
The monitor comes with a Navi Key, a multi-directional control that helps navigate the On-Screen Display (OSD) menu.
Up/Down/Left/Right:
- selecting function menus and items
- adjusting function values
- entering into/exiting from function menus
Middle:
- launching the On-Screen Display (OSD)
- entering submenus
- confirming a selection or setting
Hot Key
- Users may enter into preset function menus by moving the Navi Key up, down, left or right when the OSD menu is inactive.
- Users may customize their own Hot Keys to enter into different function menus.
Gaming
1st Level Menu | 2nd/3rd Level Menu | Description |
Game Mode | User | - Use Up or Down Button to select and preview mode effects.
- Press the Middle Button to confirm and apply your mode type.
|
FPS |
Racing |
RTS |
RPG |
Night Vision | OFF | - This function optimizes background brightness and is recommended for FPS games.
|
Normal |
Strong |
Strongest |
A.I. |
Response Time | Normal | - Response Time will be grayed out while MPRT is enabled.
|
Fast |
Fastest |
MPRT | OFF | - When MPRT is enabled, Brightness cannot be enabled and will be grayed out.
- MPRT and HDCR cannot be enabled simultaneously.
- Response time will be grayed out while MPRT is enabled.
- MPRT has to be disabled while Adaptive-Sync is set to ON.
- MPRT is available when the refresh rate is over 85Hz.
|
ON |
Refresh Rate | Location | Left Top | - Location is adjustable in OSD Menu. Press the Middle Button to confirm and apply your Refresh Rate Location.
- This monitor follows and works at the Operating System's preset Screen Refresh Rate.
|
Right Top |
Left Bottom |
Right Bottom |
OFF |
ON |
Alarm Clock | Location | Left Top | - After setting the time, press the Middle Button to activate the timer.
- Users have to manually restore their preset Alarm Clock after any AC power loss and reconnection.
|
Right Top |
Left Bottom |
Right Bottom |
OFF |
15:00 | 00:01 ~ 99:59 |
30:00 |
45:00 |
60:00 |
Screen Assistance | None | - Users can adjust Screen Assistance in any mode.
|
Icon | |
Adaptive-Sync | OFF | - Adaptive-Sync prevents screen tearing.
- DisplayPort or HDMI default is ON and can be adjusted ON/OFF in any mode, any resolution, any input source and any screen refresh rate.
- MPRT will be disabled if AdaptiveSync is enabled.
|
ON |
Professional
1st Level Menu | 2nd Level Menu | Description |
Pro Mode | User | - Use Up or Down Button to select and preview mode effects.
- Press the Middle Button to confirm and apply your mode type.
|
Anti-Blue |
Movie |
Office |
sRGB |
Eco |
Low Blue Light | OFF | - Low Blue Light protects your eyes against blue light. When enabled, Low Blue Light adjusts the screen color temperature to a more yellow glow.
- When Pro Mode is set to Anti-Blue, it is mandatory to enable Low Blue Light.
|
ON |
HDCR | OFF | - HDCR enhances image quality by increasing the contrast of images.
- When HDCR is set to ON, Brightness will be grayed out.
- HDCR and MPRT cannot be enabled simultaneously.
|
ON |
MPRT | OFF | - When MPRT is enabled, Brightness cannot be enabled and will be grayed out.
- MPRT and HDCR cannot be enabled simultaneously.
- Response time will be grayed out while MPRT is enabled.
- MPRT has to be disabled while AdaptiveSync is set to ON.
- MPRT is available when the refresh rate is over 85Hz.
|
ON |
Image Enhancement | OFF | - Image Enhancement enhances image edges to improve their acutance.
|
Weak |
Medium |
Strong |
Strongest |
Image
1st Level Menu | 2nd/3rd Level Menu | Description |
Brightness | 0-100 | - Properly adjust Brightness according to the surrounding lighting.
- Brightness will be grayed out when MPRT or HDCR are enabled.
|
Contrast | 0-100 | - Properly adjust Contrast to relax your eyes.
|
Sharpness | 0-5 | - Sharpness improves clarity and details of images.
|
Color Temperature | Cool | - Use Up or Down Button to select and preview mode effects.
- Press the Middle Button to confirm and apply your mode type.
|
Normal |
Warm |
Customization | R (0-100) |
G (0-100) |
B (0-100) |
Screen Size | Auto | - Users can adjust Screen Size in any mode, any resolution and any screen refresh rate.
|
4:3 |
16:9 |
1st Level Menu | 2nd Level Menu | Description |
HDMI1 | - Select an Input Source from the list.
|
HDMI2 |
DP |
Auto Scan | OFF | - Users can use the Navi Key to select Input Source at below status:
- While "Auto Scan" is set to "OFF" with the monitor at power saving mode;
- While "No Signal" message box is shown on the monitor.
|
ON |
Navi Key
1st Level Menu | 2nd Level Menu | Description |
Up Down Left Right | OFF | - Up Button default is Game Mode.
- Down Button default is Screen Assistance.
- Left Button default is Alarm Clock.
- Right Button default is Input Source.
- All Navi Key items can be adjusted via OSD Menus.
|
Brightness |
Game Mode |
Screen Assistance |
Alarm Clock |
Input Source |
Refresh Rate |
Info. On Screen |
Night Vision |
Setting
1st Level Menu | 2nd Level Menu | Description |
Language | 繁體中文 | - Users have to press the Middle Button to confirm and apply the Language setting.
- Language is an independent setting. Users' own language setting will override the factory default. When users set Reset to Yes, Language will not be changed.
|
English |
Français |
Deutsch |
Italiano |
Español |
한국어 |
日本語 |
Русский |
Português |
简体中文 |
Bahasa Indonesia |
Türkçe |
(More languages coming soon) |
Transparency | 0~5 | - Users can adjust Transparency in any mode.
|
OSD Time Out | 5~30s | - Users can adjust OSD Time Out in any mode.
|
Power Button | OFF | - When set to OFF, users can press the power button to turn off the monitor.
|
Standby | - When set to Standby, users can press the power button to turn off the panel and backlight.
|
Info. On Screen | OFF | - The information of the monitor status will be shown on the right side of the screen.
|
ON |
HDMI CEC | OFF | - HDMI CEC (Consumer Electronics Control) supports Sony PlayStation®, Nintendo® Switch™, Xbox Series X|S consoles and various audio-visual devices that are CECcapable.
- If HDMI CEC is set to ON:
- The monitor will automatically power on when the CEC device is turned on.
- The CEC device will enter power saving mode when the monitor is turned off.
- When Sony PlayStation®, Nintendo® Switch™, or Xbox Series X|S console is connected, Pro Mode will be automatically set to Eco (Default) and can be adjusted to users' preferred modes later.
|
ON |
Reset | YES | - Users can Reset and restore settings to original OSD Default in any mode.
|
NO |
Specifications
Monitor | Optix G273 |
Size | 27 inch |
Curvature | Flat |
Panel Type | IPS |
Resolution | 1920x1080 @165Hz |
Aspect Ratio | 16:9 |
Brightness (nits) | 300 (typ.) |
Contrast Ratio | 1000:1 |
Refresh Rate | 165Hz |
Response Time | 1ms (MPRT) |
I/O | - HDMI x 2
- DP x 1
- Headphone Jack x 1
|
View Angles | 178°(H), 178°(V) |
DCI-P3*/ sRGB | 94% / 131% |
Surface Treatment | Anti-glare |
Display Colors | 16.7M |
Monitor Power Options | 19.0V 2.1A |
Power Adapter Specs | - Option 1: ADS-40SI-19-3 19040E
- Option 2: DA-40A19
|
Power Input | 100~240Vac, 50~60Hz, 1.0A max |
Power Output | 19.0V 2.1A |
Adjustment (Tilt) | -5° ~ 20° |
Kensington Lock | Yes |
VESA Mounting | - Plate Type: 100 x 100 mm
- Screw Type: M4 x 10 mm
- Thread Diameter: 4 mm
- Thread Pitch: 0.7 mm
- Thread Length: 10 mm
|
Dimension (W x H x D) | 614.9 x 444.6 x 228.38 mm |
Weight | 4.5Kg (Net) 7.1Kg (Gross) |
Environment | Operating | - Temperature: 0℃ ~ 40℃
- Humidity: 20% ~ 90%, non-condensing
- Altitude: 0 ~ 5000m
|
Storage | - Temperature: -20℃ ~ 60℃
- Humidity: 10% ~ 90%, non-condensing
|
* Based on CIE1976 test standards.
Preset Display Modes
Standard | Resolution | HDMI | DP |
VGA | 640x480 | @60Hz | V | V |
@67Hz | V | V |
@72Hz | V | V |
@75Hz | V | V |
Dos-Mode | 720x480 | @60Hz | V | V |
720x576 | @50Hz | V | V |
SVGA | 800x600 | @56Hz | V | V |
@60Hz | V | V |
@72Hz | V | V |
@75Hz | V | V |
XGA | 1024x768 | @60Hz | V | V |
@70Hz | V | V |
@75Hz | V | V |
SXGA | 1280x1024 | @60Hz | V | V |
@75Hz | V | V |
WXGA+ | 1440x900 | @60Hz | V | V |
WSXGA+ | 1680x1050 | @60Hz | V | V |
Full HD | 1920x1080 | @60Hz | V | V |
@85Hz | V | V |
@120Hz | V | V |
@144Hz | V | V |
@165Hz | X | V |
Video Timing Resolution | 480P | V | V |
576P | V | V |
720P | V | V |
1080P @60Hz | V | V |
1080P @120Hz | V | V |
Troubleshooting
The power LED is off.
- Press the monitor power button again.
- Check if the monitor power cable is properly connected.
No image.
- Check if the computer graphics card is properly installed.
- Check if the computer and monitor are connected to electrical outlets and are turned on.
- Check if the monitor signal cable is properly connected.
- The computer may be in Standby mode. Press any key to activate the monitor.
The screen image is not properly sized or centered.
- Refer to Preset Display Modes to set the computer to a setting suitable for the monitor to display.
No Plug & Play.
- Check if the monitor power cable is properly connected.
- Check if the monitor signal cable is properly connected.
- Check if the computer and graphics card are Plug & Play compatible.
The icons, font or screen are fuzzy, blurry or have color problems.
- Avoid using any video extension cables.
- Adjust brightness and contrast.
- Adjust RGB color or tune color temperature.
- Check if the monitor signal cable is properly connected.
- Check for bent pins on the signal cable connector.
The monitor starts flickering or shows waves.
- Change the refresh rate to match the capabilities of your monitor.
- Update your graphics card drivers.
- Keep the monitor away from electrical devices that may cause electromagnetic interference (EMI).
Safety Instructions
- Read the safety instructions carefully and thoroughly.
- All cautions and warnings on the device or User Guide should be noted.
- Refer servicing to qualified personnel only.
Power
- Make sure that the power voltage is within its safety range and has been adjusted properly to the value of 100~240V before connecting the device to the power outlet.
- If the power cord comes with a 3-pin plug, do not disable the protective earth pin from the plug. The device must be connected to an earthed mains socket-outlet.
- Please confirm the power distribution system in the installation site shall provide the circuit breaker rated 120/240V, 20A (maximum).
- Always disconnect the power cord or switch the wall socket off if the device would be left unused for a certain time to achieve zero energy consumption.
- Place the power cord in a way that people are unlikely to step on it. Do not place anything on the power cord.
- If this device comes with an adapter, use only the MSI provided AC adapter approved for use with this device.
Battery
Please take special precautions if this device comes with a battery.
- Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer.
- Avoid disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, which can result in an explosion.
- Avoid leaving a battery in an extremely high temperature or extremely low air pressure environment that can result in an explosion or the leakage of flammable liquid or gas.
- Do not ingest battery. If the coin/button cell battery is swallowed, it can cause severe internal burns and can lead to death. Keep new and used batteries away from children.
Overuse of screens is likely to affect eyesight.
Recommendations:
- Take a 10-minute break for every 30 minutes of screen time.
- Children under 2 years of age should have no screen time. For children aged 2 years and over, screen time should be limited to less than one hour per day.
Technical Support
If a problem arises with your product and no solution can be obtained from the user's manual, please contact your place of purchase or local distributor. Alternatively, please visit https://www.msi.com/support/ for further guidance.
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download MSI Optix G273 - Full HD WLED Gaming LCD Monitor Manual
Need Assistance?
Do you have a question about the Optix G273 that isn't answered in the manual? Leave your question here.