Kenmore KW3010 - Household Dry Canister Vacuum Cleaner Manual

BEFORE USING YOUR NEW DEVICE

Read this Use & Care Guide. It will help you assemble and operate your new Kenmore vacuum cleaner in the safest and most effective way.

For more information about vacuum cleaner care and operation, call the Vacuum Cleaner Help Line at 1-877-531-7321 (US) / 1-844-608-3081 (CA). You will need the complete model and serial numbers when requesting information.

Your vacuum cleaner's model and serial numbers are located on the Model and Serial Number Plate. Record the model number and serial number of your new Kenmore vacuum cleaner.

PACKING LIST

Your KENMORE VACUUM CLEANER is packaged with the following parts and components assembled separately in the carton:

PARTS AND FEATURES

It is important to know your vacuum cleaner's parts and features to assure its proper and safe use. Review these before using your vacuum cleaner.

To order a replacement part, call 1-877-531-7321 (US) / 1-844-608-3081 (CA).

NOTE: The hose and accessories for this dry vacuum are 1-1/4'' (32mm) diameter.

Please pay special attention to these hazard alert boxes, and follow any instructions given. WARNING statements alert you to such hazards as fire, electric shock, burns and personal injury. CAUTION statements alert you to such hazards as personal injury and/or property damage.

ASSEMBLY INSTRUCTIONS

Before assembling the vacuum cleaner, check the PACKING LIST. Use this list to verify that you have received all the components of your new Kenmore Vacuum Cleaner.

Electrical Shock Hazard. DO NOT plug into electrical supply until assembly is complete. Failure to do so could result in electrical shock or injury. To reduce the risk of electric shock, do not expose to rain.

1. Undo the latches.
   
2. Lift the powerhead off the collection tank and remove the pre-filter.
   
3. Remove the contents from inside the collection tank; make sure you have all contents as listed above.
4. Before vacuuming, fit the dust bag flange onto the inlet port, taking care not to damage the bag.
   
5. Your vacuum comes ready for dry vacuum cleaning. If the pre-filter is not installed, refer to "INSTALLING & CLEANING PRE-FILTER" section for installation instructions.
6. Place the powerhead onto the collection tank and secure it with the latches.
   
7. Insert the locking end of the hose into the vacuum port of the collection tank and turn clockwise to lock into place.
   
8. Choose the desired accessory and insert onto the end of hose or extension wand.
   

OPERATING INSTRUCTIONS

VACUUMING OPERATION

Be sure to read, understand, and apply information entitled 'important safety instructions'. Do not vacuum in areas with flammable gases, vapors, or explosive dusts in the air. Flammable gases or vapors include but are not limited to: lighter fluid, solvent type cleaners, oil-based paints, gasoline, alcohol, or aerosol sprays. Explosive dusts include but are not limited to: coal, magnesium, grain, or gun powder. To reduce the risk of health hazards from vapors or dust, do not vacuum toxic materials.

Do not plug the power cord into electrical supply. Make sure the plug is disconnected before changing the filters.

Do not vacuum drywall dust, fireplace soot, or ash with this vacuum. This is a very fine dust which will not be captured by the filter and may cause damage to motor.

NOTE: To reduce the risk of electric shock, this vacuum cleaner has a polarized plug; one blade is wider than the other. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

THIS VACUUM IS INTENDED FOR DRY PICK-UP ONLY.

1. Verify that the power cord is disconnected from the outlet.
   
2. Before vacuuming, fit the dust bag flange onto the inlet port, taking care not to damage the bag.
   
3. In order to prepare your vacuum for dry vacuuming, make sure the edge of the filter fits snugly along the edge of the collection tank. Your vacuum comes with the filter pre-installed. For installation instructions, see "INSTALLING & CLEANING PRE-FILTER" section
4. Place the powerhead back on the collection tank and secure it in place using the latches.
   
5. Insert the locking end of the hose into the vacuum port on the collection tank and turn clockwise to lock into place.
6. Choose the desired accessory and insert onto the end of hose or extension wand.
   
7. The air flow regulation on the hose handle allows you to adjust the amount of vacuum suction. For best cleaning results, fully close the air flow regulation.
   NOTE: Open the air flow regulation for lightweight rugs or thick carpets. Close the air flow regulation suction for upholstery, hard floor or low pile carpets.
   
8. Pull out the power cord slowly.
   
9. Plug the power cord into the outlet, turn on the dry vacuum by pressing the power button once.
   
10. Once you have finished vacuuming, press the power button again to turn the vacuum off and unplug the cord from the power outlet.
11. To rewind the cord, hold onto the vacuum port to ensure unit remains stationary and turn the cord rewind knob clockwise

ATTACHMENTS

All included attachment tools can be inserted into either the hose or the extension wand.

MULTI-SURFACE FLOOR NOZZLE

Use the standard setting for carpet cleaning. Push the carpet/bare floor selector down to release the brush and squeegee to transition to bare floor cleaning.

CREVICE TOOL

For vacuuming edges, gaps, and reaching tight spaces.

ROUND DUSTING BRUSH

For vacuuming fragile or easily scratched items, such as furniture and drapes.

PRODUCT MAINTENANCE AND CARE

EMPTYING THE COLLECTION TANK

Always follow all safety precautions when performing maintenance to the vacuum cleaner.

Always disconnect the plug from the outlet before removing the powerhead from the collection tank.

1. Verify that the power cord is disconnected from the outlet.
   
2. Disconnect the hose from the vacuum by turning counter-clockwise.
   
3. Undo the latches and remove the powerhead from the collection tank. Place powerhead on a soft, clean surface upside down.
   
4. Clear all dirt and debris from the collection tank and hose into a proper waste container.
5. Clean or replace the filters.
6. Check the hose, accessories, and power cord to verify that they have not been damaged.
7. Place the powerhead back on collection tank and secure latches.

INSTALLING & CLEANING PRE-FILTER

INSTALLING PRE-FILTER

1. Verify that the power cord is disconnected from the outlet.
   
2. Remove the powerhead and place in an upside-down position.
3. Install the pre-filter onto the rim of the collection tank. Make sure the edge of the filter fits snugly along the edge of the collection tank.
   NOTE: Ensure the dust bag and the prefilter are correctly installed before each use.
   
4. Place the powerhead back onto the collection tank.

REMOVING & CLEANING PRE-FILTER

1. Remove the pre-filter by lifting up.
   
2. Clean the pre-filter by gently tapping or brushing dirt off. If necessary, gently rinse the pre-filter with cool clean water. Do not scrub or brush the prefilter. Allow the pre-filter to air dry for 24 hours before re-installing. DO NOT install pre-filter if it is damp, or it will damage the vacuum.
3. For optimal performance, it is recommended to replace the pre-filter every 3 to 6 months.
4. Install cleaned or new filters as above in steps 2-4 of Installing Pre-Filter.

REMOVING & CLEANING THE AIR INLET FILTER

1. Verify that the power cord is disconnected from the outlet
   
2. With the removed powerhead in an upside-down position, carefully remove the air inlet filter from the tabs.
   
3. Wash and rinse the air inlet filter with cool clean water.
4. Allow the wet filter to air dry for 24 hours before re-installing.

Make sure that the pre-filter and air inlet filter are dry before use, otherwise it may cause poor cleaning performance or damage to the motor.

5. Re-install the cleaned air inlet filter.
6. Place the powerhead back onto the collection tank.

REMOVING & CLEANING EXHAUST FILTER

1. Verify that the power cord is disconnected from the outlet.
   
2. Unlock the exhaust filter door by lifting both of the locking tabs upwards and pull the door out.
   
3. Remove the exhaust filter from the vacuum and clean by gently tapping or brushing off dirt. If necessary, gently rinse the exhaust filter with cool clean water. Do not scrub or brush the exhaust filter while wet. Allow the exhaust filter to air dry for 24 hours before reinstalling.
   
4. For optimal performance, it is recommended to replace the old exhaust filter with a new filter every year.

Make sure the exhaust filter is dry before use.

5. Install the cleaned or new filter. Then insert the filter door tabs into the upper slots and lock the filter door into place.
   

Clean or change all filters regularly for best performance. ALWAYS USE FILTERS FOR DRY VACUUMING. If the machine is used without the filters, the motor will burn out and the warranty will be voided. Always keep spare filters on hand.

NOTE: All of the filters included are made of high-quality materials designed to stop small dust particles. The vacuum and all of the included filters should be used for dry pick-up only. Dry filters are necessary to pick up dust. If the filter is wet, it will clog quickly and be very difficult to clean. Handle all of the filters carefully when removing it for cleaning and or replacing. Check the filters for tears or small holes. A small hole can let dust pass through and out of the filter. Do not use a filter with holes or tears; replace it immediately.

STORAGE

Before storing your vacuum, the collection tank should be emptied and cleaned. The accessories should be cleaned and stored so they can be readily available when needed. Store the vacuum indoors.

1. Store the power cord in place by rotating the cord rewind knob clockwise as shown.
   NOTE: To prevent the power cord from getting stuck, do not retract the cord too fast or in wrong direction.
   
2. Place the wands onto the accessory storage.
3. The floor nozzle has a storage hook that slides into the slot on the back of the collection tank.
   

REPAIRS

Repairs for this vacuum should be performed only by qualified service personnel using only identical replacement parts.

TROUBLESHOOTING

Review this table to find do-it-yourself solutions for minor performance problems. Any service needed, other than maintenance described in this Use & Care Guide, should be performed by a qualified service agent.

Always turn off and unplug vacuum cleaner before performing maintenance to the vacuum cleaner. Failure to do so could result in electrical shock or personal injury.

IMPORTANT SAFETY INSTRUCTIONS

Read all instructions in this guide before assembling or using your vacuum cleaner.

Your safety is important to us. To reduce the risk of fire, electrical shock, injury to persons or damage when using your vacuum cleaner, follow basic safety precautions including the following:

• Use only as described in this Use & Care Guide. Use only with manufacturer's recommended attachments.
• Do not leave vacuum cleaner when plugged in. Unplug from outlet when not in use and before servicing.
• Do not use outdoors or on wet surfaces.
• Do not allow to be used as a toy. Close attention is necessary when used by or near children.
• Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, call 1-877-531-7321 (US) / 1-844-608-3081 (CA) for assistance.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run vacuum cleaner over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce air flow.
• Do not handle plug or vacuum cleaner with wet hands.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Turn off all controls before unplugging.
• Use extra care when cleaning on stairs.
• Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without dust bag and/or filters in place.
• Hold plug when rewinding cord reel. Do not allow plug to whip when rewinding.

To reduce the risk of injury from moving parts - Unplug before servicing.

To reduce the risk of electric shock - Unplug before cleaning or servicing.

SAVE THESE INSTRUCTIONS
Proper assembly and safe use of your vacuum cleaner are your responsibilities. Your vacuum cleaner is intended for Household Use. Read this Use & Care Guide carefully for important use and safety information. This guide contains safety statements under warning and caution symbols.

LIMITED WARRANTY

Direct all claims for warranty service to: 1-877-531-7321 (US) / 1-844-608-3081 (CA).
Cleva North America, Inc., Greenville SC 29607

Vacuum Cleaner Help Line:
1-877-531-7321 (US) / 1-844-608-3081 (CA)
8:00am-5:00pm EST, M-F
www.kenmorefloorcare.com

Documents / Resources

References

• Kenmore Floor Care | Home Cleaning Solutions & Products

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Kenmore KW3010 - Household Dry Canister Vacuum Cleaner Manual