Table of Contents
Advertisement
Available languages
Available languages
6. Turn the power head collar
above. Ensure the collar is securely tightened. If loose, the
product may not function as intended.
NOTE: Do not overtighten the collars. Overtightening may cause
damage to the tool.
Attaching Brush (Fig. F)
CAUTION: After installing a brush, ensure it is properly
seated and restrained to prevent the brush from falling off
by pulling the brush gently away from the power head
1. Slide the brush
onto the brush connector
8
2. Turn the brush clockwise to secure as shown by the
brush lock/unlock arrow
3. To remove brush, turn the brush counterclockwise.
Adjusting Pole Length (Fig. G)
The upper pole
length can be adjusted for greater reach
4
by pulling out the extension pole
1. Release the pole latch
2. Slide the extension pole to the desired length.
3. Lock the pole latch.
Adjusting Latch Tightness (Fig. A, G)
The pole latch screw comes set to a default tightness, but
over time and continued use, the screw may loosen.
To ensure the pole latch
extension pole
is securely tightened, it must be set to an
10
appropriate tightness.
NOTE: The pole latch may be open or closed when adjusting.
•
To adjust the pole latch tightness, use a screwdriver:
-
To tighten, turn the pole latch screw
-
To loosen, turn the pole latch screw counterclockwise.
Pivoting Power Head (Fig. H)
When using the pole
, there are five positions for the power
4
head
to give you the best angle for the application.
3
•
To set the desired angle, press the pivot button
rotate the power head forward or backward until the
pivot button marker
location markers
. The pivot button must pop back
27
out to ensure the power head is securely seated to avoid
damage and injury.
Optional Accessories
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with this
product, use of such accessories with this appliance
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
NOTE: Some accessories may not be included in your
model. Refer to product packaging for contents. Additional
accessories are available at local retailers.
WARNING: Do not use general purpose brushes (black
bristles) on painted surfaces.
WARNING: Before using any brush, wash and inspect the
brush and bristles for wear and debris. Do not use if bristles
are worn or washing does not remove the debris.
clockwise as seen from
6
9
.
25
.
10
.
14
closes securely and the
14
clockwise.
15
lines up with one of the pivot
26
.
3
.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
Installing and Removing the Battery Pack
(Fig. I)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
NOTE: For best results, make sure your battery pack
fully charged.
•
To install the battery pack into the tool:
1. Lift the battery compartment latch
2. Pull the battery compartment hook
base notch
3. Pull the battery compartment
4. Align the battery pack with the rails inside the
and
16
battery compartment and slide it in until the battery
pack is firmly seated in the tool, and ensure it does
not disengage.
5. Close the battery compartment by looping the battery
compartment hook over and into the base notch and
pushing the battery compartment latch down until it
clicks into place.
WARNING: Never operate scrubber with compartment
open to keep water away from battery pack.
•
To remove the battery pack:
1. Lift the battery compartment latch.
2. Pull the battery compartment hook out of the base notch.
3. Pull the battery compartment away from the base.
4. Press the battery pack release button
pull the battery pack out of the tool handle. Insert it
into the charger as described in the charger section of
this manual.
5. Close the battery compartment by looping the battery
compartment hook over and into the base notch and
pushing the battery compartment latch down until it
clicks into place.
Soft‑bristle brush: gray
Medium‑bristle brush: red
Hard‑bristle brush: black
Hook‑and‑loop backer: black
Lambswool cloth: white
Knit microfiber head: red
Microfiber pad: gray
18
.
28
away from the base
17
ENgliSh
is
1
.
out of the
19
.
5
and firmly
2
9
Advertisement
Table of Contents
