Table of Contents
Advertisement
70/WAHAVIK ?
d.
e.
URETOR {bha
about
1mm
"yJ1mm
—
idle Screw
TER BER
. To set the high speed needle: (large needle sticking out from the carburetor body), turn the screw as pictured. Initial high speed
needle setting should be 3-3.5 turns (close the needle completely, then back out 3~3.5 turns). Clockwise turn will provide leaner
setting (lower fuel to air mixture), and counterclockwise turn will provide richer setting (higher fuel to air mixture).
. To set the carburetor idle: (small needle sticking out from the carburetor body), turn the screw as pictured. Initial idle setting
should leave 1mm carburetor gap. Clockwise turn will provide higher idle (larger carburetor opening), and counterclockwise turn
will provide lower idle (smaller carburetor opening). For more details about the engine setting, please refer to ENGINE
BREAK-IN/SETTING procedures to properly set the engine.
. To set the low speed needle: (The low-speed mixture screw is located in the end of the carburetor). turn the screw as pictured.
This screw controls how much fuel enters the engine at idle and low throttle. This adjustment will smooth the idle and improve the
acceleration to mid speed. Make this adjustment with the throttle closed, after setting the idle. Turn the screw clockwise gently until
it bottoms out. DO NOT over tighten. Now turn the low-speed mixture screw counter-clock 6 1/2 turns.
Remove the outer foam from filter and make it moist evenly with a few drops of fuel. Put the filter in a plastic bag and knead it until
the foam is saturated, but not soaked.
Finally, make sure the air cleaner boot is securely fastened with a zip-tie.
Never run your vehicle without the air filter .If the vehicle will be operated in an area with fine dust, use filter oil or caster oil instead of
fuel. It is important that the foam is only moist to trap dirt and allow air passage. With the foam too wet, limited air can pass through;
therefore, limiting engine performance.
e
DAHAR
: EDO
(EEOAE SERRARA)
^ ODER -
AEREA
ER~.
SAE
CHEE
SHSROOFSEABE3-3.5880)
» SABRES
COAR
ES ERRA
: AS
ERRA
E
^ iA
SISE
(EFHSE RR SS RETRUEEEBBUS [RE e
. ARISE : BXXES SE GRE ESDUR FRU
^ REIO
Ba SES BU VUES QAR)
AEAEE
ER mmB9 BRL ^ Reus
ORARET
ARR Ea : UDDSEIDRES
ARR
S S82 mc SEE ERR REUTERS
o
. MAE
: ENRE
P.L:ÉBBEBAS CEGEOESTBSIUOB
SS TER KU) ^ WÜcEEzR ^ HAERE
ARR iTi.
[8
WUE OESTTESSSHSRUEFERABHO.50B)
^ FEARCHAR
A ER BRCH EGER ER DURS ^ . BS EELECOER ST PAA
^ MURARE
ETN
°
. RAMASE
RRAS"
ERRAR
RAE
SOE
S L "
TANE
RENONS
ERR o
Ex E RES EST XE IURI dio PR T EDIERMA o
S ISESB 7 ES EC ZESRUROG SS I Xo P3888 ^ EERDE
A L I F " MEREN
BRRR
^ ESSREPHHISSSDUREUS SS
ERFESHI » S4 EGEUIEBRE °
. Remove the cap from fuel bottle nozzle.
. Squeeze the fuel bottle, insert into fuel, and draw fuel into the fuel bottle. The fuel used should be methanol based model engine
glow fuel (available at hobby shops) with 1096 to 3096 nitro content and 5% to 1896 caster/synthetic oil content for lubrication.
. Fill car's fuel tank with glow fuel.
. BADHA
9
. HEDH
RAIRA
EAA ^
. TIBIAS
2 8 » AENEA
11
Advertisement
Table of Contents
