Advertisement
•ssszzz.
Transmission
and
Reception
of
Bulk Data
The
SOI can
transmit or receive the
internal
data using
MIDI
system
exclusive
message
(bulk
data).
Therefore
if
it
is
connected
to
another SOI,
that
data
can be
easily transferred
between two
units.
For
example
in live
performance,
if
using
two
units
of
SOls
as
main
one and
sub,
you
can
load
programs
into the
first
SOI
in
a usual
way
and send
them from
the
first
to
the
second SOI
in
the
method
explained
below.
If
programs
are
spanning
several
disks, this
tip
will
save
you
loading
the
same
data
into the
second SOI, exchanging
disks.
Data
transmission or reception
is
also available
in
MIDI
sample
dump
standard format.
In
this
case,
the
SOI
will
send
or receive only
sampled
data
w
ithout
any parameter
settings
.
This enables
you
to
make
samples
on
the
SOI, send
them
to
other
samplers compatible
to
MIDI
sample
dump
standard format,
and
edit
those
sampled
materials
on
the other
samplers, or vice
versa.
When
you
transfer
bulk
data,
you
should
make
a
MIDI
"hand
shake" connection between
the
SOI and
another
MIDI
device;
i.e.
as the
SOI
's
MIDI
OUT
is
connected
to the
device
's
MIDI
IN,
and
vice versa.
m
Transmission
1
Select
"PROG.
NO."
in
the
MIDI
index
in
Edit
mode.
If
sending a sample
data,
first
press
a
bank
key and
select
a
bank
that
contains the
data.
While
holding
down
the
REC
key, turn the data entry
knob,
and
the
SO
1
enters
Bulk
dump
mode.
*
At
this
time the
PROG.
NO./DATA
display
will
show
the
MIDI channel used
for
transmission
and
reception
of
bulk
data.
If
you use two
or
more
units of
the
S01
s
in
your
MIDI system
and
you wish
to
specify the
unit
that
the bulk
data
is
sent
to,
use
this
channel as
the
device
number.
Otherwise,
set
it
to "1"
using the
data
entry
knob.
2.
Press the
REC
key,
and
the
PROG. NO./DATA
display
will
show
"STA"
or
"SOI".
Select
either
using
the data entry
knob.
STA:
Sends
the
sampled
data
in
the current bank,
in
MIDI
sample
dump
standard format.
SOI:
SendsdatainSOl
exclusive format.
When
it
is
selected,
press the
REC
key
again
to select
the data
type.
The
PROG. NO./DATA
display
will
show
the
data
type:
S:
Sends
the
SAMPLE
file;
sample and
its
start
point,
end
point,
and
loop
setting.
Aj
Sends any
parameter
settings
other than those included
in
SAMPLE
files.
(*)The
attribute of
each parameter
is
explained
on page
51
3
Press the
REC
key,
and
the
PROG. NO./DATA
display
will
show
"Ten".
To
execute bulk
dumping,
press the
REC
key
again.
The
PROG. NO./DATA
display
will
blink
showing "Trn"
while bulk
data
is
being
sent.
When
the
transmission
is
finished, the
SOI
will
return to step
1.
If
you
continue, repeat the
same
operation.
*
If
any key
other than the
REC
key
is
pressed
in
each
step, the
S01
will
exit
Bulk
dump
mode.
Advertisement
