1. Manuals
  2. Brands
  3. BenQ Manuals
  4. Projector
  5. MW809STH
  6. Installation manual

BenQ MW809STH Installation Manual

Projector rs232 command control
Hide thumbs Also See for MW809STH:
Table of Contents

Advertisement

Quick Links

Download this manual
MW809STH
Projector RS232 Command Control
Installation Guide

Advertisement

Table of Contents
loading

Related Manuals for BenQ MW809STH

Summary of Contents for BenQ MW809STH

  • Page 1 MW809STH Projector RS232 Command Control Installation Guide...

  • Page 2: Table Of Contents

    Table of Contents Introduction .............................. 3 Wire arrangement ........................3 RS232 pin assignment ....................... 3 Connections and communication settings ................ 4 RS232 serial port with a crossover cable ............... 4 Settings ............................4 RS232 via LAN ........................... 7 Settings ............................7 RS232 via HDBaseT ........................

  • Page 3: Introduction

    Introduction The document describes how to control your BenQ projector via RS232 from a computer. Follow the procedures to complete the connection and settings first, and refer to the command table for RS232 commands. Available functions and commands vary by model. Check the specifications and user manual of the purchased projector for product functions.

  • Page 4: Connections And Communication Settings

    Connections and communication settings Choose one of the connections and set up properly before RS232 control. RS232 serial port with a crossover cable D-Sub 9 pin (male) on a projector PC or laptop D-Sub 9 pin (female) Communication cable (crossover) Settings On-screen images in this document are for reference only.
  • Page 5 Determine the COM Port name used for the RS232 communications in Device Manager. Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected.
  • Page 6 Finish Serial port setup. Baud rate 9600 / 14400 / 19200 / 38400 / 57600 / 115200* *Default Baud rate Data length 8 bit Parity check None Stop bit 1 bit Flow control None...

  • Page 7: Rs232 Via Lan

    RS232 via LAN RJ45 port on a projector PC or laptop LAN cable Settings Find the Wired LAN IP address of the connected projector from the OSD menu and make sure the projector and the computer are within the same network. Input 8000 in the TCP port # field.

  • Page 8: Rs232 Via Hdbaset

    RS232 via HDBaseT HDBaseT compatible device RJ45 port on a projector D-Sub 9 pin RJ45 PC or laptop D-Sub 9 pin LAN cable Settings Determine the COM Port name used for the RS232 communications in Device Manager. Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected.
  • Page 9 Finish Serial port setup. Baud rate 9600 / 14400 / 19200 / 38400 / 57600 / 115200* *Default Baud rate Data length 8 bit Parity check None Stop bit 1 bit Flow control None...

  • Page 10: Command Table

    Command table • Available features differ by projector specification, input sources, settings, etc.. • Commands are working if the standby power is 0.5W or a supported baud rate of the projector is set. • Uppercase, lowercase, and a mixture of both types of characters are accepted for a command. •...
  • Page 11 Write Volume + <CR>*vol=+#<CR> Write Volume - <CR>*vol=-#<CR> Write Volume level for <CR>*vol=value#<CR> customer Read Volume Status <CR>*vol=?#<CR> Write Mic. Volume + <CR>*micvol=+#<CR> Write Mic. Volume - <CR>*micvol=-#<CR> Read Mic. Volume Status <CR>*micvol=?#<CR> Write Audio pass Through off <CR>*audiosour=off#<CR> Write Audio-Computer1 <CR>*audiosour=RGB#<CR>...
  • Page 12 Write ISF Day <CR>*appmod=isfday#<CR> Write ISF Night <CR>*appmod=isfnight#<CR> Write <CR>*appmod=threed#<CR> Write Sport <CR>*appmod=sport#<CR> Write <CR>*appmod=hdr#<CR> Write <CR>*appmod=hlg#<CR> Read Picture Mode <CR>*appmod=?#<CR> Write Contrast + <CR>*con=+#<CR> Write Contrast - <CR>*con=-#<CR> Write Set Contrast value <CR>*con=value#<CR> Read Contrast value <CR>*con=?#<CR> Write Brightness + <CR>*bri=+#<CR>...
  • Page 13 Temperature-lamp native Read Color Temperature <CR>*ct=?#<CR> Status Write Aspect 4:3 <CR>*asp=4:3#<CR> Write Aspect 16:6 <CR>*asp=16:6#<CR> Write Aspect 16:9 <CR>*asp=16:9#<CR> Write Aspect 16:10 <CR>*asp=16:10#<CR> Write Aspect 2.35:1 <CR>*asp=2.35#<CR> Write Aspect Auto <CR>*asp=AUTO#<CR> Write Aspect Real <CR>*asp=REAL#<CR> Write Aspect Letterbox <CR>*asp=LBOX#<CR> Write Aspect Wide <CR>*asp=WIDE#<CR>...
  • Page 14 Write 4 Corners Top-Left-Y <CR>*cornerfittly=+#<CR> Increase Read 4 Corners Top-Left-Y <CR>*cornerfittly=?#<CR> Status Write 4 Corners Top-Right-X <CR>*cornerfittrx=-#<CR> Decrease Write 4 Corners Top-Right-X <CR>*cornerfittrx=+#<CR> Increase Read 4 Corners Top-Right-X <CR>*cornerfittrx=?#<CR> Status Write 4 Corners Top-Right-Y <CR>*cornerfittry=-#<CR> Decrease Write 4 Corners Top-Right-Y <CR>*cornerfittry=+#<CR>...
  • Page 15 Write 4 Corners <CR>*cornerfitbry=-#<CR> Bottom-Right-Y Decrease Write 4 Corners <CR>*cornerfitbry=+#<CR> Bottom-Right-Y Increase Read 4 Corners <CR>*cornerfitbry=?#<CR> Bottom-Right-Y Status Write Digital Zoom In <CR>*zoomI#<CR> Write Digital Zoom out <CR>*zoomO#<CR> Write Auto <CR>*auto#<CR> Write Brilliant color on <CR>*BC=on#<CR> Write Brilliant color off <CR>*BC=off#<CR>...
  • Page 16 status Write Menu Position - Center <CR>*menuposition=center#<CR> NO Write Menu Position - <CR>*menuposition=tl#<CR> Top-Left Write Menu Position - <CR>*menuposition=tr#<CR> Top-Right Write Menu Position - <CR>*menuposition=br#<CR> Bottom-Right Write Menu Position - <CR>*menuposition=bl#<CR> Bottom-Left Read Menu Position Status <CR>*menuposition=?#<CR> Write Direct Power On-on <CR>*directpower=on#<CR>...
  • Page 17 Settings-Monitor Out Status Write 2400 <CR>*baud=2400#<CR> Write 4800 <CR>*baud=4800#<CR> Write 9600 <CR>*baud=9600#<CR> Write 14400 <CR>*baud=14400#<CR> Baud Rate Write 19200 <CR>*baud=19200#<CR> Write 38400 <CR>*baud=38400#<CR> Write 57600 <CR>*baud=57600#<CR> Write 115200 <CR>*baud=115200#<CR> Read Current Baud Rate <CR>*baud=?#<CR> Read Lamp <CR>*ltim=?#<CR> Read Lamp2 Hour <CR>*ltim2=?#<CR>...
  • Page 18 燈) Read Lamp Mode Status <CR>*lampm=?#<CR> Read Model Name <CR>*modelname=?#<CR> Read System F/W Version <CR>*sysfwversion=?#<CR> Read Scaler F/W Version <CR>*scalerfwversion=?#<CR> Read Format F/W version <CR>*formatfwversion=?#<CR> Read Lan F/W Version <CR>*lanfwversion=?#<CR> Read MCU F/W Version <CR>*mcufwversion=?#<CR> Read Ballast F/W Version <CR>*ballastfwversion=?#<CR> Write Blank On <CR>*blank=on#<CR>...
  • Page 19 Write 3D nVIDIA <CR>*3d=nvidia#<CR> Read 3D Sync Status <CR>*3d=?#<CR> Write Remote Receiver On <CR>*rr=on#<CR> Write Remote Receiver Off <CR>*rr=off#<CR> Write Remote <CR>*rr=fr#<CR> Receiver-front+rear Write Remote Receiver-front <CR>*rr=f#<CR> Write Remote Receiver-rear <CR>*rr=r#<CR> Write Remote Receiver-top <CR>*rr=t#<CR> Write Remote <CR>*rr=tf#<CR> Receiver-top+front Write Remote <CR>*rr=tr#<CR>...
  • Page 20 <CR>*tint=+#<CR> Write Tint - <CR>*tint=-#<CR> Write Set Tint value <CR>*tint=value#<CR> Read Get Tint value <CR>*tint=?#<CR> Write Set BenQ gamma value <CR>*gamma=value#<CR> Color Calibration Read Gamma value status <CR>*gamma=?#<CR> (only for service) Write Set HDR Brightness <CR>*hdrbri=value#<CR> value Read Get HDR Brightness <CR>*hdibri=?#<CR>...
  • Page 21 Write Set Red Gain value <CR>*RGain=value#<CR> Read Get Red Gain value <CR>*RGain=?#<CR> Write Green Gain + <CR>*GGain=+#<CR> Write Green Gain - <CR>*GGain=-#<CR> Write Set Green Gain value <CR>*GGain=value#<CR> Read Get Green Gain value <CR>*GGain=?#<CR> Write Blue Gain + <CR>*BGain=+#<CR> Write Blue Gain - <CR>*BGain=-#<CR>...
  • Page 22 Write Color Gamut BT.2020 <CR>*cgamut=bt.2020#<CR> Write Color Gamut DCI-P3 <CR>*cgamut=dci-p3#<CR> Read Color Gamut Value <CR>*cgamut=?#<CR> Write Dynamic Iris ON <CR>*diris=on#<CR> Write Dynamic Iris OFF <CR>*diris=off#<CR> Read Dynamic Iris status <CR>*diris=?#<CR> Write Color Calibration Save <CR>*colorsave#<CR> Write Color Calibration <CR>*colorpattern=value#<CR> pattern display Write Service mode enable for <CR>*error=enable#<CR>...

  • Page 23: Faq Video

    (2) How to use RS232 cable connection to power on & off projector? https://youtu.be/faGUvcDBmJE (3) How to set up RS232 cable connection? https://youtu.be/CYJRqyO6K1w (4) How to use RS232 command to request fan speed and temperature value? https://youtu.be/KBXEd-BCDKQ BenQ.com © 2022 BenQ Corporation All rights reserved. Rights of modification reserved. Version: 1.01-C...

Table of Contents