Advertisement
3.1.2 COMPONENT input ADC
3.1.2.1 Component Gain/Offset Adjustment
- Convert to Component in Input-source
- Signal equipment displays
Impress Resolution 480i
Model: 209 in Pattern Generator(480i Mode)
Pattern : 65 in Pattern Generator( MSPG-925 SERIES)
Adjustment pattern (COMPONENT )
- Adjust by commanding AUTO_COLOR_ADJUST.
3.1.2.2 Confirmation
- We confirm whether "0xB3 (480i)/0xBC (1080i)" address of
EEPROM "0xA2" is "0xAA" or not.
- If "0xB3 (480i)/0xBC(1080i)" address of EEPROM "0xA2"
isn't "0xAA", we adjust once more
- We can confirm the ADC values from "0xAD~0XB2
(480i)/0XB6~BB (1080i)" addresses in a page "0xA2"
*Manual ADC process using Service Remocon. After enter
Service Mode by pushing "ADJ" key,
execute "ADC Adjust" by pushing "
CALIBRATION :COMPONENT".
Impress Resolution 480i
3.2 Function Check
3.2.1 Check display and sound
-Check Input and Signal items. (cf. work instructions)
1. TV
2. AV (SCART1/SCART2/CVBS/S-Video)
3. COMPONENT (1080i)
4. RGB (PC : 1360x1080 @ 60Hz)
5. DVI (PC : 1360x1080 @ 60Hz)
6. HDMI
6. PC Audio In
* Display and Sound check is executed by Remote controller.
Copyright
2008
LG Electronics. Inc. All right reserved.
C
Only for training and service purposes
4. Total Assembly line process
4.1 Adjustment Preparation
- W/B Equipment condition
- Above 5 minutes H/run in the inner pattern. ("power on" key
- 15 Pin D-Sub Jack is connected to the AUTO W/B
- Adjust Process will start by execute I2C Command (Inner
- Adjust Process will finish by execute I2C Command (Inner
** Caution **
Color Temperature: COOL, Medium, Warm
One of R Gain/G Gain/ B Gain should be kept on 0xC0, and
adjust other two lower than C0.
(when R/G/B Gain are all C0, it is the FULL Dynamic Range of
Module)
* W/B condition
- Surrounding Temperature : 20 % ~ 80 %
" key at "ADC
- Surrounding Temperature : 25±5 °C
- warm-up Time : Under 5 Min.
*Manual W/B process using adjusts Remote control.
- After enter Service Mode by pushing "ADJ" key,
- Enter White Pattern off of service mode, and change off -> on.
- Enter "W/B ADJUST" by pushing "
ADJUST".
Module
LGD
- 17 -
CA210: CH 9, Test signal: Inner pattern (85IRE)
of adjust remote control)
EQUIPMENT.
pattern (0xF3, 0xFF).
Cool
9,300k
Color
Medium
°
8,000k
Temperature
Warm
6,500k
Cool
Min : 130
Luminance
Medium
Min : 130
2
(cd/
m )
Warm
Min : 130
pattern (Inner pattern (0xF3,0x00)).
Luminance
Min
Typ
250
300
X=0.285 (±0.003)
°
K
Y=0.293 (±0.003)
X=0.295 (±0.003)
K
<Test Signal>
Y=0.305 (±0.003)
Inner pattern
X=0.313 (±0.003)
°
K
Y=0.329 (±0.003)
(216gray,85IRE)
Typ : 220
Typ : 220
Typ : 220
" key at "3. W/B
Remark
1360*768@60hz
LGE Internal Use Only
Advertisement
