ASSEMBLY GUIDE M SERIES : QUICKFLY M1D RIGGING GRIDS AND ACCESSORIES This Assembly Guide provides instructions on how to safely assemble and use the MG-1D multipurpose grid, the MTG-1D top grid and the MUB-1D multipurpose U-bracket. Following are descriptions of major components and how they work together, and examples of common uses.
CONSEQUENTLY, USERS OF QUICKFLY RIGGING SYSTEMS SHOULD BE PREPARED TO TAKE ADDITIONAL SAFETY ASSURANCE MEASURES BEYOND THOSE OUTLINED IN THIS MANUAL. IN ALL CASES, IT IS THE RESPONSIBILITY OF THE USER TO MAKE CERTAIN THAT ANY MEYER SOUND LOUDSPEAKER SYSTEM IS SUSPENDED IN ACCORDANCE WITH ALL APPLICABLE NATIONAL/FEDERAL, STATE/PROVINCIAL, AND LOCAL REGULATIONS.
Parts specific to a QuickFly system should be ordered directly from Meyer Sound. No attempt should be made to substitute what appears to be equivalent or “mostly the same” generic replacements. Some parts used in QuickFly systems are identical to those used in other rigging applications. To the best of our knowledge, most of these suppliers are reputable and their products are reliable.
NOTE: For large M1D arrays with or without M1D-Subs it is recommended that you use the MTG-1D top grid or MG-1D multipurpose grid. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
Top grid cam pin position Bottom grid cam pin position Total angle +8° (up tilt) To Grid To Grid QRP locations Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356 Page 6 of 24...
(grid side facing the Sub). In this case, up tilt from 0° to +14° increments is possible. Use M1D links to complete the rest of the array. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
WARNING: The leveling feet must always be detached from the MG-1D multipurpose grid before flying a system. Unscrew the entire assembly, including the threaded leg, and remove completely. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
M1D-Sub). In this case, down tilt from 0° to -14° in 2-degree increments is possible. Use M1D links to complete the rest of the array. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
To further secure larger arrays, particularly in outdoor situations, use a tie down or weight on the grid or a safety system on the array. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com...
WARNING: The leveling feet must always be detached from the MG-1D grid before flying a system. Unscrew the entire assembly, including the threaded leg, and remove completely. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
WARNING: The leveling feet must always be detached from the MG-1D grid before flying a system. Unscrew the entire assembly, including the threaded leg, and remove completely. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
WARNING: The leveling feet must always be detached from the MG-1D grid before flying a system. Unscrew the entire assembly, including the threaded leg, and remove completely. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
MSL-4s can also be flown independently with the MG-1D grid from a single pick-up point on the frame’s center bracket. Other Meyer Sound loudspeakers with the same footprint as the MSL-4 (DF-4 and DS-4P) can be used in this configuration.
CAUTION: The leveling feet must always be detached from the MG-1D multipurpose grid before flying a system. Unscrew the entire assembly, including the threaded leg, and remove completely. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
(grid side facing the M1D-Sub). In this case, up tilt from 0° to +14° in 2-degree increments is possible. Use M1D links to complete the rest of the array. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
M1D-Sub). In this case, up tilt from 0° to +14° in 2-degree increments is possible. Use M1D links to complete the rest of the array. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
For floor mounted configurations, positive angles are used for down tilt. The MUB-1D U-bracket provides from +10° to -12° of tilt in 2-degree increments. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
WARNING: Always use mounting and rigging hardware that has been rated to meet or exceed the weight of the loudspeakers being hung. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356...
Maximum Load Ratings. WARNING: Always use mounting and rigging hardware that has been rated to meet or exceed the weight being hung. Meyer Sound Laboratories Inc. T: +1 510 486.1166 PN: 05.115.001.01 B www.meyersound.com F: +1 510 486.8356 Page 22 of 24...