Table of Contents
Advertisement
INDOOR UNIT
ESTABLISHING
COMMUNICATIONS
SEARCHING FOR
INDOOR EQUIPMENT
WITH EQUIPMENT
PLEASE WAIT
WORKING
SOFTWARE
VERSION
Fig. 13 - - Power Up Sequence
NOTE: If the variable- -speed indoor equipment (furnace or fan
coil) cannot be found, the User Interface will display "CANNOT
COMMUNICATE WITH INDOOR UNIT". This MUST be
corrected before the initial power up sequence can continue. If
indoor unit is found, but outdoor unit is not found, "OUTDOOR
UNIT NOT IDENTIFIED" will appear. Proceed to the next section
for Outdoor Unit Identification.
Selecting Outdoor Unit
If there is no communicating outdoor unit, the screen, shown in
Fig. 14, will appear. Press either Left or Right Up/Down button to
select AC (air conditioner), HP (heat pump), or None (no unit
installed). Press right- -side button to continue to next screen.
OUTDOOR UNIT
OUTDOOR UNIT
NOT IDENTIFIED
ENTER HEAT PUMP
SELECT TYPE:
NONE
SIZE
NONE, AC, HP
18000 TO 60000 BTU
PRESS +/- TO MAKE
PRESS +/- TO MAKE
SELECTION
SELECTION
CONTINUE
BACK
Fig. 14 - - Selecting Outdoor Unit
If either AC or HP has been selected as the outdoor unit type, the
middle screen will appear (See Fig. 14). Press either Left or Right
Up/Down button to select appropriate Btu size of outdoor unit,
then press right side button to continue. If a NIM (Network
Interface Module) is applied for non- -communicating two- -stage
outdoor equipment, select 1 or 2- -stage compressor operation, and
press right- -side button to continue.
NOTE: Range of outdoor unit Btu selection is limited by model
number of indoor unit installed. The Evolution Zone Control will
not allow an outdoor unit size that is not supported by the installed
indoor unit.
NOTE: On new system installations, the model and serial number
will be recognized and displayed. On any indoor/outdoor board
replacements, the equipment will be recognized but the exact
model/serial number will not be displayed.
Selecting Electric Heater
If the equipment is a fan coil, packaged heat pump, or packaged
AC and the electric heater is not self- -identifying, "ELECTRIC
HEATER NOT IDENTIFIED" will appear (See Fig. 15). Press
either Left or Right Up/Down button to select appropriate size of
electric heater installed, then press right- -side button to continue.
An asterisks (*) will appear next to electric heater sizes that may
cause excessive airflow.
ELECTRIC HEATER
NOT IDENTIFIED
ENTER SIZE:
NONE, 5,10,15 KW
PRESS +/- TO MAKE
SELECTION
BACK
Fig. 15 - - Selecting Electric Heater
OUTDOOR UNIT
SEARCHING FOR
OUTDOOR EQUIPMENT
WORKING
A03195
OUTDOOR UNIT
HEAT PUMP
36000 BTU
ENTER NUMBER OF
SPEEDS, 1 or 2:
1
PRESS +/- TO MAKE
SELECTION
CONTINUE
BACK
CONTINUE
A03196
5 KW
CONTINUE
A03197
NOTE: Range of electric heaters available is limited by model
number of the equipment installed. The Evolution Zone Control
will not allow an electric heater size that is not supported by the
installed equipment.
Hydronic Heat Applications
The Evolution Zone Control supports Hydronic Heat applications
in the form of a hot water coil on FE fan coils only. If an FE fan
coil is installed, a Hydronic Heat kit should be installed in place of
the electric heater. See FE fan coil Product Data for accessory part
number. The system will identify that hydonic heat has been
installed during the initial commissioning process. The system will
treat the hot water coil as either auxiliary heat in a heat pump
application, or the sole heat source. Setup options for Hydronic
Heat applications are described in the Setup section of this
instruction.
Selecting Accessories
Once the indoor and outdoor equipment have been found or
entered, the following screens will appear allowing the Installer to
select the "AIR FILTER TYPE; HUMIDIFIER INSTALLED";
and "UV LIGHTS INSTALLED" (See Fig. 16). Use either Left or
Right Up/Down button to make appropriate selections in the
highlighted area on the display screen. Press right- -side button to
continue (or advance) to the next screen.
ACCESSORIES
ACCESSORIES
AIR FILTER TYPE:
HUMIDIFIER
EAC
EAC
INSTALLED?
MEDIA
MEDIA + EAC
PRESS +/- TO MAKE
PRESS +/- TO MAKE
SELECTION
SELECTION
CONTINUE
BACK
AIR FILTER MEDIA TYPE
HUMIDIFIER INSTALLED?
Fig. 16 - - Accessories —UV Lights
Air Filter Type
This accessory screen will appear first. The installer will need to
enter the type of filter (AIR FILTER, AIR CLEANER, or AIR
PURIFIER). See Table 1 and make a selection using Left or Right
Up/Down button, then press right- -side button to continue.
Table 1 – Filter Selection
INSTALLED FILTER
1 inch to 4 inch media
High voltage EAC
Evolutiont Air Purifier
Humidifier Installed
This will appear after the Air Filter Type screen. Select whether a
humidifier is installed on the system, YES or NO, then press
right- -side button to continue.
UV Lights Installed
This screen will appear to select whether UV lights are installed on
the system, select YES or NO, then press right- -side button to
continue.
Zoning
"SEARCHING FOR ZONE EQUIPMENT" will appear on the
screen to identify the number of zones detected. This screen will
show Zone 1, Zone 2, etc. and indicate all zones having either a
Remote Room Sensor, or smart sensors associated with them. If the
system contains smart sensors, they must be assigned a zone
number before continuing. See Smart Sensor Installation
Instructions on how to assign Smart Sensors to their respective
zones. When finished, press right- -side button to continue. See Fig.
17.
6
ACCESSORIES
U.V. LIGHTS
YES
INSTALLED?
YES
PRESS +/- TO MAKE
SELECTION
CONTINUE
BACK
CONTINUE
U.V. LIGHTS INSTALLED?
A03198
MENU
SELECTION
AIR FILTER
AIR CLEANER
AIR PURIFIER
Advertisement
Table of Contents
