Roland MT-32 Owner's Manual page 38

@Main volume
Status Second Third
BaH O7H vwH
vy = Volume Value OOH - 7FH ( 0 - 127 }
n = MIDI Channel OH- FH (1
- 1)
Can contro] the volume of the rhythm part
The maximum volume is determined by Master volume and Expression message.
@ Expression
Status Second Third
BnR OBH wH
vv © Expression 00H ~ 7FH ( 0 - 127 }
a = MIDI Channet OH~ FH (1- 1368)
Controls the volume of a Part accessible through the received MID] channel. The
maximum volume is determined by Master volume and Main Volume message.
@Hold-1
Status Second Third
BnH 40H vwH
w= OOH ~ SFH : off
w = 40H ~ 7FH : on
n = MID! Channel OH- FH (1+ 16)
@RPC LSB
Status Second Third
BnH 64H wH
w = The lower byte of a parameter number controlled by RPC. (Refer to RPC MSB)
n « MIDI Channel OH- FH (1- 16)
@RPC MSB
Status Second Third
BoH 65H vwH
vv = The upper byte of a parameter number controlied by RPC.
n = MIDI Channel OH - FH (2 - 16)
MSB and LSB RPC together specifies parameter to be controlled while Data entry
determines the value.
Effective RPC an MT - 32 is Bender range.
RPC Data Entry Description
WSB LSB
OOH 00H = WH Bender Range
weod- 24
Unit in semitone, 2 octaves maximus
@ Resets All Controllers
Stotus Second Third
BoH 79H 00H
n = MID! Channel OH- FH (1- 16)
Sets controllers to the value as shawn below.
Controiler setting
Modulation Depth OFF { o)
Expression MAK € 127)
Hold 1 - OFF he 0)
Pitch Bender Change CENTER
@ritcn penger cnange
@ Pitch Bender
Status Second Third
Ent Lick mm
= Pitch Bender change value ( Lower byte )
OOH - 7FH ( 0 - 127 )
mm = Pitch Bender change baiue ( Upper byle )
OOH - 7FH ( 0 - 127 }
fn = MIDI Channel OH - FH ( 1- 16)
mExclusive
Status
FOH : System Exciusive
F7H ; OX (End Of Exciusive)
Using exclusive message, a set af parameters for a individual parameters in a rhythm
part can be transferred to MT - 32.
Refer to Roland Exclusive Messages and Sections 4 and 5.
4.EXCLUSIVE COMMUNICATION
Parameters for patches or timbres can be transferred to"from MT ~ 32 through
Exciusive message.
Mode] ~ 1D # of MT- 32 is 16H.
in a system where more than one MIDI channel is assigned to MT - 32, Unit # may
be set to the MT ~ 32 instead of Device- ID + of a basic. channel. The advaniage
of Unit # is that a specific part is made accessible independent of MIDI channel of
that part.
Whether to use MID] channel or Unit # depends on parameter address.
MT - 32 recognizes MIDI channels 1 thru 16 and Unit + 1 thru 32 as Device ~ ID
#. Note that the actual Device - 1D # is the number 1] less MIDI channel number or
Unit #.
mOne way communication
Request Data 1 RQ? 11H
Byte Description
POH Excjusive status
aul Manufacturer's ID ( Roland )
DEV Device 1D
15H Model 1D
VK Compand 1D ( RQ )
all Address USB tel
eal Address .
eal Address LSB
ssi Size MSB
ssi Size
ssi Size LSB
SUB Check sum
FIH BOX ( End Of Exclusive )
Data set 1 DT1 12H
Byte Description
FO Exclusive status
lH Manufacturer's [D ( Roland )
Diag Device ID
16H Model 1D
12H Cowzand ID DT) )
aall Address MSB tal
aall Address
eal Address LSB
ddl Data + 4-2
Sut Check sun
FW EOX { End Of Exclusive }