Pioneer VSX-4950S Operating Instructions Manual page 44

VSX-4900S/VSX-4950S/VSX-51 REMOTE CONTROL OPERATION
Learning capacity and buttons that can learn
The buttons shown in the diagram can learn, By changing the CONTROL
MODE, a single button can be used to learn a maximum of nine
commands, enabling a total of 261 commands to be learned. However,
the capacity for learning differs depending on the remote control signal.
With Pioneer remote controf signals, about 70 commands can be
learned.
CONTROL MODE
Learning function
button
{Learning procedure]
. Press the LEARN button to switch to the LEARN mode.
. Press one of the CONTROL MODE buttons.
. Press ane of the Learning function buttons.
. Receive a remote control signal from another remote control and
learn.
{Operation example]
As a learning example, an explanation follows on how to use the
CONTROL MODE VCR 1 [> ]button to learn the VCR PLAY signal.
Place the transmission sections of the programmable remote control
unit and the remote control of the VCR facing each other.
NOTE:
Be sure to place the remotes on a stable surface such as a table while
doing this. Also, avoid placing near fluorescent lighting fixtures or in
direct sunlight. When programing operations, use new batteries.
1 to 2 inches
PWN
Place the two units on a table, separated by 2 to 5 cm (1 to 2 inches).
Memorization will not be possible if they are too close.
1. Press the LEARN button.
* Alt the CONTROL MODE buttons flash at random.
2. Press the VCR 1 CONTROL MODE button.
* Only the VCR 1 button flashes.
3. Press the fe] button.
button has learned the new signal.
44
< ARBI318 >
During the jearning operation, if you press the VCR "> |button
twice, or move the remote control, correct learning is not possible.
To continue learning with other buttons, continue from procedure 2.
learning has been completed.
{When 'Seareinal is not possible}
After the selected CONTROL MODE button (for example VCR 1) flashes
twice, and all the CONTROL MODE buttons flash, repeat the learning
operation from procedure 2.
{When learning is not possible because memory is full]
After the selected CONTROL MODE button {for example VCR 1) flashes
four times, the LEARN MODE is canceled.
ff the memory becomes full even when you have used only a small
number of buttons for learning, take the following steps.
* Try learning once more using the button that resulted in full memory.
Memory may appear to be full even when it isn't due to the two remote
controls being too far apart, not enough power remaining in the batteries,
or the effect of light from fluorescent lighting fixtures or direct sunlight.
* Check buttons already used for learning.
if the CONTROL MODE button remains lit after you have quickly pressed
and released a button used for fearning, memorization in that button
is incorrect, resulting in the memory full condition. If you perform learning
once more, abnormal data is cleared, returning you to normal conditions.
NOTE:
* After pressing the LEARN button, if you do not press a button within
about 30 seconds, the LEARN MODE is canceled.
* After pressing one CONTROL MODE button, if you do not press a
button that can learn within about 30 seconds, the LEARN MODE
is canceled. If a button other than a one that can learn is pressed,
the condition for CONTROL MODE button input is resumed.
* After pressing an operation button that can learn, if a remote control
signal is not received within 45 seconds, the LEARN MODE is
canceled,
Per Serna si slit
In the EDIT MODE, there is the PRESET MODE and MULTL-EDIT MODE.
PRESET MODE (TV, VCR 1, VCR 2)
12 kinds of remote control signal formats are already preset for basic
TV and VCR functions. if they conform to your TV or VCR functions,
you can automatically preset operation buttons with the desired format's
remote contro! signals and use to commands operations. It is not
necessary to learn commands one at a tirne.
Preset operation buttons are indicated in the diagram by UR: E
When you also want to use other buttons, use the LEARN operation
to memorize commands.