Table of Contents
Advertisement
@ FM/AM ANTENNA terminals
Use these antenna terminals for reception of normal FM and AM
broadcasts.
@ GND terminal
Connect the turntable ground lead to this terminal.
@) CENTER, REAR PRE AMP OUT and POWER AMP IN
jacks
[CENTER PRE AMP OUT]
When a separate power amplifier is used to drive the center speaker,
connect the power amplifier to this jack.
(CENTER POWER AMP IN]
When a separate pre-amplifier is connected and this unit is used as
power amplifier, connect the pre-amplifier to this jack.
{REAR PRE AMP OUT}
When a separate power amplifier is used to drive the rear speakers,
connect the power amplifier to these jacks.
[REAR POWER AMP IN)
When a separate pre-amplifier is connected and this unit is used as
power amplifier, connect the pre-amplifier to these jacks.
@ CENTER SPEAKER terminals
Connect the center speaker to these terminals.
NOTE:
Do not allow any of the cord's conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
Use center speaker of impedance 82 —
16Q.
G) REAR SPEAKERS terminals
Connect the rear speakers to these terminals.
NOTE:
Do not allow any of the cord's conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
Use rear speakers of impedance
8Q —
16 Q.
© AC OUTLETS
(U.S. and Canadian models]
SWITCHED TOTAL 50 W MAX
Power supplied through these outlets is turned on and off by the
receiver's POWER
switch.
Total electrical power consumption
of
connected equipment should not exceed 50 W.
UNSWITCHED 200 W MAX
Power flows continually to this outlet, regardless of whether the receiver
is switched ON or OFF. Electrical power consumption of the connected
equipment should not exceed 200 W.
The equipment should be disconnected by removing the power plug
from the wall socket when not in regular use, e.g. when on vacation.
[Multi-voltage model]
SWITCHED TOTAL 100 W MAX
Power supplied through these outlets is turned on and off by the
receiver's POWER
switch. Total electrical power consumption
of
connected equipment should not exceed 100 W.
UNSWITCHED 200 W MAX
Power flows continually to this outlet, regardless of whether the receiver
is switched ON or OFF. Electrical power consumption of the connected
equipment should not exceed 200 W.
The equipment should be disconnected by removing the power plug
from the wall socket when not in regular use, e.g. when on vacation.
NOTE:
Do not connect appliances with high power consumption such as
heaters, irons, or television sets to the AC OUTLETS
in order to avoid
overheating or fire risk.
This can cause the receiver to malfunction.
Wi?
Gi-y4sele
@ INPUT jacks
(8) TAPE 1/DAT jacks
Use these to connect a first cassette deck or DAT (digital audio tape
deck).
Connecting for Recording
The tape recording jack (REC) on the cassette deck or DAT should be
connected to the REC side of the TAPE 1/DAT jack on the receiver with
a pin plug connecting cord.
Connecting for Playback
Connect the PLAY jack on the cassette deck or DAT to the PLAY side
of the TAPE 1/DAT jack on the receiver with a pin plug connecting cord.
(9) TAPE 2 jacks
Connect a second cassette deck to these jacks.
Connecting for Recording
The tape recording jack (REC) on the cassette deck should be connected
to the REC side of the TAPE 2 jack on the receiver with a pin plug
connecting cord.
Connecting for Playback
SG
Connect the PLAY jack on the cassette deck to the PLAY side of the
TAPE 2 jack on the receiver with a pin plug connecting cord.
FRONT PRE AMP OUT and POWER AMP IN jacks
[PRE AMP OUT]
When a separate power amplifier is used to drive the front speakers,
connect the power amplifier to these jacks.
[POWER AMP IN]
When a separate pre-amplifier is connected and this unit is used- as
power amplifier, connect the pre-amplifier to these jacks.
@ TV jacks
{VIDEO IN}
Connect the TV tuner's VIDEO OUTPUT to this jack.
[AUDIO IN (L, R)]
Connect the TV tuner's AUDIO OUTPUT to these jacks.
@ VDP/CDV jacks
[VIDEO IN]
When watching the video image from a LD player (VDF?) ora CDV player,
connect its VIDEO OUTPUT jacks here.
[AUDIO IN (L, R)]
When playing back the audio channel from a LD player (VDP) or a CDV
player, connect its AUDIO OUTPUT jacks here.
@3 VCR 1 jacks
{VIDEQ- OUT]
Connect to the VIDEO INPUT jacks of the first VCR.
[AUDIO OUT {L, R)]
Connect to the AUDIO INPUT jacks of the first YCR.
[VIDEO IN}
Connect to the VIDEO OUTPUT jack of the first VCCR.
[AUDIO IN (L, R)}]
Connect to the AUDIO OUTPUT jacks of the firt CR.
VCR 2 jacks
[VIDEO OUT]
Connect to the VIDEO INPUT jacks of the secord \/CR.
{AUDIO OUT IL, R)!
Connect to the AUDIO INPUT jacks of the second "VCR,
{VIDEO IN]
Connect to the VIDEO OUTPUT jack of the secinc VCR.
71
Advertisement
Table of Contents
