Page 1
Important Note The shape of your purchased model (IT-300-35E) differs partly from the product illustrated in the User's Guide. Please substitute the information provided below in the illustrations on the pages indicated. [E-14] Left Front Right Back Bottom...
Page 3
Handheld Terminal Series User’s Guide Be sure to read “Safety Precautions” inside this guide before trying to use your Handheld Terminal.
Page 4
Microsoft and Windows are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Information in this document is subject to change without advance notice. CASIO Computer Co., Ltd. makes no representations or warranties with respect to the contents or use of this manual and speci¿...
Contents Safety Precautions ..................E-3 Operating Precautions ...................E-8 Important ......................E-10 Regulatory Information ................E-11 Checking in the Box ..................E-13 Handheld Terminal System Confi guration ..........E-14 General Guide ....................E-16 IT-300 ......................... E-16 USB and Charging Unit ..................E-19 Loading and Removing the Battery Pack ...........E-20 Loading ......................
Page 6
® Performing Bluetooth Communication .............E-37 Resetting the Handheld Terminal ..............E-38 Performing a Full Reset (Initialization) ............E-38 Warning Label ....................E-40 Using the Dual Battery Charger (HA-D32DCHG) ........E-41 General Guide ....................E-41 Charging a Battery Pack..................E-43 Connecting Multiple Dual Battery Chargers............E-44 Speci¿...
Safety Precautions Congratulations upon your selection of this CASIO product. Be sure to read the following Safety Precautions before trying to use it for the ¿ rst time. Your neglect or avoidance of the warning and caution statements in the subsequent pages causes the danger of ¿...
Page 8
Warning Dust and Moisture Though the Handheld Terminal is dust and water splash resistant, its options including the battery pack are not. Keep loose metal objects and containers ¿ lled with liquid away from your Handheld Terminal and the options. Also, never handle the Handheld Terminal and the options while your hands are wet.
Page 9
Caution Foreign Objects Take care to ensure that metals or combustible objects are not inserted into the openings of the Handheld Terminal or its options, and not to allow moisture to get inside of them. Location Install the cradle properly on a À at and stable surface so that it cannot fall down onto À...
Page 10
Immediately rinse it off with clean tap water and then consult a physician. Caution Replace only with the same type of battery pack recommended by CASIO. Dispose of used battery packs according to the local regulation. Keep the battery pack out of the reach of small children.
Page 11
Backup of All Important Data Caution Note that CASIO Computer Co., Ltd. shall not be held liable to you or any third party for any damages or loss caused by deletion or corruption of data due to use of the Handheld Terminal, malfunction or repair of the Handheld Terminal or its peripherals, or due to the batteries going dead.
Operating Precautions Your Handheld Terminal and its options are precision. Improper operation or rough handling can cause problems with data storage and other problems. Note and observe the following precautions to ensure proper operation. Do not leave dead battery pack in the Handheld Terminal for a long period. Dead battery pack can leak, leading to malfunction and damage to the Handheld Terminal.
Page 13
Lithium-ion Battery Pack Each lithium-ion battery pack has its life. The life span heavily depends on how the battery pack is charged or stored which may cause deterioration of the battery pack to shorten the life span if it is handled improperly. Note the tips below to make the battery pack last long.
Important This guide does not include any information about programming and download procedures. See the applicable separate documentation for information about the procedures. After Service Should this product ever malfunction, contact your original retailer providing information about the product name, the date you purchased it, and details about the problem.
HA-J65US Trade Name: CASIO Responsible party: Industrial Handheld Division Casio America, Inc. Address: 570 Mt. Pleasant Avenue, Dover, New Jersey 07801, USA Telephone number: 973-361-5400 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 16
Optional models HA- , HA-D32DCHG and HA-D20BAT-A are in conformity with the J65US Council Directive 2004/108/EC. Manufacturer: CASIO COMPUTER CO., LTD. 6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan Representative within the European Union: CASIO EUROPE GmbH Casio-Platz 1, 22848 Norderstedt, Germany E-12...
Checking in the Box Please check the contents of the box before using the Handheld Terminal for the ¿ rst time. Open the box and make sure that all the items shown here are included. USB and Charging Unit Handheld Terminal (HA-J65US) Battery Pack (HA-D20BAT-A)
Power Cord for Europe AC-CORD-EU Power Cord for North America AC-CORD-US Power Cord for Taiwan AC-CORD-TW Power Cord for Korea AC-CORD-KR Power Cord for Australia AC-CORD-AU For the latest options list, refer to the ON-LINE manual available at http://world.casio.com/system/pa/UsersGuide/sup85_e.html E-14...
Page 19
Options USB and Charging Unit Cables HA-J65US HA-J80USBM HA-J81USBH Screen Protect Sheet HA-J90PS5 E-15...
General Guide IT-300 Left Front Right Back Bottom E-16...
Page 21
Indicator 1 Orange: Charging Green: Charging complete Red Flashing: Battery pack error or the surrounding temperature is out of the charging temperature range Indicator 2 Blue Flashing: BT in use Orange Flashing: WLAN in use Magenta Flashing: Ready to communicate (when USB- connected) Red: Barcode read error Green: Successful read...
Page 22
20 microSD Card Slot Slot a microSD card into here. Cover 21 Lock Switches Used to lock the covers and to release. 22 Battery Pack Cover Used to cover the battery compartment that holds the battery pack inside. 23 Reset Switch Used to reset the Handheld Terminal.
USB and Charging Unit Bottom Left Right AC Adaptor Jack Connect the AC adaptor here. USB Port Connect the cable (HA-J80USBM) here. Power Supply/Data Used to connect to the IT-300 for USB communication or Communication power supply. Connector Stoppers Press when removing the IT-300. E-19...
Loading and Removing the Battery Pack Your Handheld Terminal uses two types of battery: a battery pack and a memory backup battery. The battery pack is used to power normal operations and to store data, while the memory backup battery provides the power required to maintain memory contents when the battery pack power is unable to supply power for some reason.
Loading 1. Turn the terminal over, turn the lock switch for the battery pack cover to the “FREE” position ( ), and then remove the battery pack cover ( 2. Load a battery pack (HA-D20BAT-A). Take care that the battery pack is oriented correctly when you load it.
Removing 1. Make sure that the Handheld Terminal is turned off. If the power is on, press the power key to turn it off. 2. Turn the terminal over, turn the lock switch for the battery pack cover to the “FREE” position ( ), and then remove the battery pack cover ( 3.
Handling the USB and Charging Unit (HA-J65US) Mount the USB and Charging Unit on the terminal when using the unit to charge the battery pack in the terminal or when connecting the terminal to another USB device using the optional cable (HA-J81USBH). Mounting the USB and Charging Unit 1.
Removing the USB and Charging Unit 1. Unlock the stoppers on the left and right sides of the USB and Charging Unit by pressing them inwards, as shown in the illustration. 2. Keeping the stoppers pressed in, pull the USB and Charging Unit off the terminal. Using the optional cable (HA-J81USBH) Plug the cable into the USB and Charging Unit and use it to connect a USB device.
Connecting to a Computer You can use the USB and Charging Unit together with the cable (HA-J80USBM) to connect the IT-300 to a computer and exchange data via USB. This combination can also be used to charge the battery pack installed in the IT-300 using power supplied from the computer.
Charging the Battery Pack The battery pack installed in the IT-300 can be charged using the optional AC adaptor (AD-S15050B). An indicator on the IT-300 shows the level of charge. You can also charge the battery pack using the optional Dual Battery Charger (HA- D32DCHG).
Dual Battery Charger (optional) Use the optional AC Adaptor for Dual Battery Charger (AD-S42120B). AC Adaptor (AD-S42120B) You can connect up to three Dual Battery Chargers. Status of Charge Indicator LED Off: Not charging Red: Charging Red Flashing: Battery pack problem Green: Charging complete Green Flashing: Standby due to the surrounding temperature being beyond the...
Attaching the Neck Strap The neck strap can be used to prevent the Handheld Terminal from fall. Since there are three strap holes where the neck strap can be attached, use the hole that affords the greatest ease of use. Attach the neck strap according to the procedure described below. To attach the neck strap 1.
Using the Touch Panel Use the touch panel by touching it lightly with your ¿ nger. Do not use objects other than your ¿ nger. You can use the touch panel in the following ways: Tap: Lightly tap the screen with your ¿ nger. Touch: Hold your ¿...
Setting the Display Brightness Adjusting Display Brightness You can use the following procedures to adjust display brightness to make it easier to read under different lighting conditions. Press the “Fn” key and then press the “5” key or “6” key after con¿ rming that “F” is displayed on the screen.
Using the Laser Scanner 1. After turning on the power, position the laser scanner close to a bar code and then press the trigger key. 2. The laser emits light and scans the bar code. If scanning is completed normally, Indicator 2 displays a green light.
Bar Code Scanning Position Position the laser scanner close to the bar code when scanning small bar codes. Position the laser scanner at a distance from the bar code so that the bars enter the light when scanning large bar codes. Margin Margin Good...
Adjusting the Laser Light Emission Width The emission width of the laser light emitted by the Handheld Terminal (model dependant) can be adjusted. Adjust the emission width when it is improper. 1. Navigate to the menus in the following sequence: Settings System The Control Panel appears as shown in the screen.
Page 38
4. Tap the [Calibration] button. The display appears as shown at right. 5. Press the trigger key to emit laser light, and align the light with the barcode for adjusting emission width. Align the laser light with the narrow bars on both sides. The message appears as shown at right when adjustment is completed.
Handling microSD Cards The Handheld Terminal supports microSD card. Install (or remove) a microSD card according to the procedure described below. Installing 1. Turn the terminal over, turn the lock switch for the microSD card slot cover to the “FREE” position, and then remove the microSD card slot cover. 2.
Removing 1. Turn the terminal over, turn the lock switch for the microSD card slot cover to the “FREE” position, and then remove the microSD card slot cover. 2. BrieÀ y push the microSD card in to release, and then remove, as shown in the illustration.
® Performing Bluetooth Communication ® Bluetooth interface can also be used to transfer data between two Handheld Terminals. ® With Bluetooth the two Handheld Terminals should be located within about three meters " ) from each other, as long as there is nothing blocking the path between them. Important! Observe the following precautions to help ensure that Bluetooth communication is successful.
Resetting the Handheld Terminal Resetting the terminal is the same as resetting a PC. Performing a reset causes all unsaved RAM data to be lost that are in mid-course of inputting and editing, but data and settings that are already stored in the FlashROM should be unaffected. Perform a reset to restore normal operation whenever the Handheld Terminal operates abnormally due to misoperation or some other reason.
Page 43
1. While holding down the Fn key and CLR key, push down the reset switch for about 3 seconds with the tip of a pointed implement such as a mechanical pencil until the message shown below appears on the display. To cancel the full reset operation, press the MENU key.
Warning Label Warning! ■ Never look directly into the laser light. These products scan using laser light. Never look directly into the laser light or shine the laser light into the eyes. This label is a warning and caution label for Class 2 laser products that comply with IEC60825-1:2007.
Using the Dual Battery Charger (HA-D32DCHG) The optionally available dual battery charger (HA-D32DCHG) can be used to simultaneously charge two battery packs. General Guide Left Right Bottom Bundled Items Connection Bracket 2 screws E-41...
Page 46
Charge Indicator This lamp indicates the charge status of the battery pack(s). Lamp Off: Not charging Red: Charging Red Flashing: Battery pack problem Green Flashing: Standby Green: Charging complete AC Adaptor Jack This is used to supply power by connecting the AC adaptor (sold separately).
Charging a Battery Pack Use the optionally available AC adaptor (AD-S42120B) for the power supply of the Dual Battery Charger. 1. Plug the cord from the AC adaptor into the AC adaptor jack of the Dual Battery Charger. 2. Plug one end of power cord into the AC adaptor and the other end to a wall outlet. 3.Taking care that the battery pack is oriented correctly, insert it into the Dual Battery Charger.
Connecting Multiple Dual Battery Chargers You can connect up to three Dual Battery Chargers. Doing so makes it possible to supply power to all the Dual Battery Chargers using one dedicated AC adaptor. 1. As shown in the illustrations below, remove the connector covers of the Dual Battery Chargers you want to connect to each other.
Page 49
Specifi cations 1. Model: HA-D32DCHG 2. Charging: Charging Method: Constant voltage (with current limiter) (when one Handheld Terminal has been mounted) Charge Period: Approx. 2 hours (1 battery pack, normal temperature) When charging two battery packs: Approx. 3.5 hours (2 battery packs, normal temperature) 3.
Using Rechargeable Battery Pack HA-D20BAT-A Important! Store a battery pack in its special soft case whenever you are not using it. If the battery pack has been left over unused for a long period of time, the capacity remained decreases due to spontaneous discharge or chemical decomposition by the battery pack itself.
Page 51
IT-300-35E IT - 3 0 0 - 3 5 E Dis p la y: Lin ea r I ma ger: 6 0 ~ 3 0 0 m m Powerclass2...
USB and Charging Unit Charging: Charging Method: Constant current/voltage Charge Period: Approximately 4 hours (AD-S15050B) Power Supply: Power Source: AC Adaptor (AD-S15050B) Consumption Current: 5V DC approximately 2.1A Output to Handheld Terminal: 5V DC 2.1A (max.) AC Adaptor Model: AD-S15050B Input: 100V to 240V AC 50/60Hz 0.36 to 0.2A Output:...