Advertisement
11. PANEL FACILITIES
@FRONT
PANEL
VSX— 3300
@® POWER switch
When
this switch
is pressed,
power
is supplied
to the unit. Press
the switch again to turn STANDBY.
@® REMOTE SENSOR
window
@ MULTI OPERATION
DISPLAY panel
@ GRAPHIC
EQUALIZER
controls
The tone
can
be adjusted.
The
equalizer
is divided
into five fre-
quency ranges
{100 Hz, 330 Hz, 1 kHz, 3.3 kHz, 10 kHz) to tailor mu-
sic to the individual taste of the listener.
® BALANCE
contro!
Use to adjust the sound
balance between
the left and right speak-
ers. When
turned to the L side, the sound
of the right speaker de-
creases,
When
turned
to the R side, the sound
of the left speaker
decreases.
© VOLUME contro!
@ SPEAKERS switches ( HL OFF,
= ON)
These are used to select the speaker through which you wish to iis-
ten.
4: When
the speakers connected
to A terminals are in use,
B: When
the speakers connected
to B terminals are in use,
*
Turn both A and B speakers to OFF position when only the
headphones are in use.
SURROUND selector switch
By pressing the A and B SPEAKERS switches, then pressing this
switch ON, you can obtain surround
reproduction.
If you press this
switch OFF again, normal
reproduction
from both speakers A and
B will be obtained.
® PHONES jack
;
Connect the plug on your
headphones
to this jack. To fisten to a
program
through
the headphones,
set both
SPEAKERS
A and
B
switches to the OFF pasition.
@ SIMULATED STEREO switch
:
This turns monaural
signals into simulated
stereo sound.
Use this
when
you wish
to experience
the sense
of stereo
presence
with
AM
broadcasts, VCR or other monaural
signal sources.
NOTE:
This function can also be used with stereo sources, but it will result
ina different sound from the normal stereo sound.
@ MEMORY
SCAN
Press this switch to scan the stations in the memory.
@ VIDEO SIGNAL SELECTOR switch
When
recording
simulcast
programs,
the
recorded image
can
be
selected from among
VDP/CDV,
VCR and video OFF.
@® FM MODE
(AUTO/MONO}
selector switch
Use to select the auto stereo mode
or monaural
mode when
listen-
ing to FM broadcasts. The monaurat
made
has been selected
when the "FM MONO"
indicator
is |it.
Auto stereo
mode;
Normatiy ieave in this mode
for reception. When
@ stereo FM
broadcast
is received, it will be automatically
reproduced
in stereo
sound.
Monaural
mode:
When
receiving
distant
stations
or stations
with
weak
broadcast
signals, the input signal may
be weak,
thus resulting in increased
noise during FM stereo broadcasts. In this event, setting the receiv-
er to the monaural
mode
will reduce
the notse. In this case, how-
ever, FM stereo broadcasts will be reproduced
in monaural
sound.
NOTE:
This switch has no effect an reception of AM broadcasts,
@ FM TUNING AUTO/MANUAL switch
Use this switch
to select either the AUTO
mode
or the MANUAL
mode. When the "AUTO" indicator is lit, the receiver is in the AUTO
mode.
@ MEMORY
switch
This is used
to memorize
stations. The
FM
MONO
mode
and
FM
AUTO
STEREO
mode
will also be memorized.
@ STATION CALL switches
These switches are used to preset and recall desired broadcasting
stations,
together
with
the
FM
MONO
mode
and
FM
AUTO
STEREO mode.
@ FM/AM selector switches
These switches are used to select euner FM or AM reception,
EM:
Press for FM reception.
AM: Press for AM reception.
@ TUNING switches (DOWN, UP}
These
switches are used to raise or lower the tuning frequency tn
the FM or AM
band.
UP:
The
FM
or AM
band
is scanned
in the direction of in-
creasing frequency.
DOWN:
The
FM
or AM
band
is scanned
in the direction
of de-
creasing frequency.
6
G4
Advertisement
