Related Manuals for New Holland IntelliView III
Summary of Contents for New Holland IntelliView III
- Page 1 SERVICE MANUAL IntelliView ™ IntelliView ™ IntelliView Plus II ™ Autoguidance and Navigation Part number 47708311 edition English December 2014...
- Page 2 Contents INTRODUCTION Electrical systems ............... 55 [55.680] Autopilot/Autoguidance ............55.1 [55.100] Harnesses and connectors.
- Page 3 INTRODUCTION 47708311 05/12/2014 Find manuals at https://best-manuals.com...
- Page 4 Contents INTRODUCTION Safety rules ..................3 Safety rules - Ecology and the environment .
-
Page 5: Safety Rules
INTRODUCTION Safety rules Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Throughout this manual you will find the signal words DANGER, WARNING, and CAUTION followed by special in- structions. - Page 6 Improper disposal of batteries can contaminate the soil, groundwater, and waterways. NEW HOLLAND strongly recommends that you return all used batteries to a NEW HOLLAND dealer, who will dispose of the used batteries or recycle the used batteries properly. In some countries, this is a legal requirement.
- Page 7 Some information could not be updated due to modifications of a technical or commercial type, or changes to the laws and regulations of different countries. In case of questions, refer to your NEW HOLLAND Sales and Service Networks. 47708311 05/12/2014...
- Page 8 INTRODUCTION 47708311 05/12/2014 Find manuals at https://best-manuals.com...
- Page 9 SERVICE MANUAL Electrical systems IntelliView III IntelliView IV IntelliView Plus II 47708311 05/12/2014 Find manuals at https://best-manuals.com...
-
Page 10: Electrical Systems
Contents Electrical systems - 55 [55.680] Autopilot/Autoguidance ............. . 55.1 [55.100] Harnesses and connectors. - Page 11 Electrical systems - 55 Autopilot/Autoguidance - 680 IntelliView III IntelliView IV IntelliView Plus II 47708311 05/12/2014 55.1 [55.680] / 1...
- Page 12 Contents Electrical systems - 55 Autopilot/Autoguidance - 680 FUNCTIONAL DATA Autoguidance module Overview - DCM-300 modem - Light Emitting Diode (LED) status indicators ......3 SERVICE Autoguidance sensors Clearance - Manual override sensor .
- Page 13 Electrical systems - Autopilot/Autoguidance Autoguidance module - Overview - DCM-300 modem - Light Emitting Diode (LED) status indicators RAIL13PLM0007FA DCM-300 modem The DCM-300 modem has two Light Emitting Diodes (LEDs) that indicate the status of the modem: • Green LED (1) •...
- Page 14 Electrical systems - Autopilot/Autoguidance Autoguidance sensors - Clearance - Manual override sensor Follow the instructions below to check the clearances for the manual override sensor on Tier 4 T8 and T9 series tractors. 1. Ensure that the steering wheel does not rub on or bind with the Forward Neutral Reverse Park (FNRP) pod.
- Page 15 Electrical systems - Autopilot/Autoguidance 6. Ensure that the FNRP pod is seated correctly on the steering column. The tab on the FNRP pod should fit into the slot on the steering column. Adjust the FNRP pod as necessary. RAIL13PLM0006AA 7. Tighten the bolt that secures the FNRP pod to the steer- ing column.
- Page 16 Electrical systems - Autopilot/Autoguidance Autoguidance sensors - Configure - Manual override sensor You can adjust the sensitivity of the Autoguidance system if the steering wheel self-rotates while Autoguidance is engaged. Prior operation: Check the clearance of the Autoguidance manual override sensor: Autoguidance sensors - Clearance - Manual override sensor (55.680).
- Page 17 Electrical systems - Autopilot/Autoguidance 9. Select “Advanced Configuration.” RAPH13DSP1003BA 10. Enter the parameter “QORC” into the “Name” window. 11. Click the “Get” button. NOTE: The default value for this parameter is 2. The max- imum value is 5. 12. Increase the value by 1. 13.
- Page 18 Index Electrical systems - 55 Autopilot/Autoguidance - 680 Autoguidance module - Overview - DCM-300 modem - Light Emitting Diode (LED) status indicators ..3 Autoguidance sensors - Clearance - Manual override sensor ..........4 Autoguidance sensors - Configure - Manual override sensor .
- Page 19 Electrical systems - 55 Harnesses and connectors - 100 IntelliView III IntelliView IV IntelliView Plus II 47708311 05/12/2014 55.2 [55.100] / 1...
- Page 20 Contents Electrical systems - 55 Harnesses and connectors - 100 FUNCTIONAL DATA Diagnostic connector External view - NAV II diagnostic connector locations ......... . . 3 47708311 05/12/2014 55.2 [55.100] / 2...
- Page 21 Electrical systems - Harnesses and connectors Diagnostic connector - External view - NAV II diagnostic connector locations T9010, T9020, T9030, T9040, T9050, and T9060 TJ280, TJ330, TJ380, TJ430, TJ480, and TJ530 The NAV II diagnostic connector is located on a harness The diagnostic connector harness removed from behind at the base of the rear right-hand pillar: the fuse panel...
- Page 22 Electrical systems - Harnesses and connectors T9.390, T9.450, T9.505, T9.560, T9.615, and T9.670 The NAV II diagnostic connector is located at the 12-pin Deutsch connector left-hand side of the fuse and relay panel: • The harness is wrapped in a corrugated plastic. RCPH10FWD187BBJ 47708311 05/12/2014 55.2 [55.100] / 4...
- Page 23 Electrical systems - Harnesses and connectors T8.275, T8.300, T8.330, T8.360, and T8.390 T8010, T8020, T8030, T8040, and T8050 TG215, TG245, TG275, and TG305 The NAV II diagnostic connector is wired directly into the 12-pin Deutsch connector 24-pin connector on the NAV II controller. RAIL13TR03436AA 47708311 05/12/2014 55.2 [55.100] / 5...
- Page 24 Electrical systems - Harnesses and connectors T8.320, T8.350, T8.380, T8.410, and T8.435 The NAV II diagnostic connector is mounted on the back 12-pin Deutsch connector wall of the fuse and relay panel in the cab. RAIL14TR04183BA 47708311 05/12/2014 55.2 [55.100] / 6...
- Page 25 Electrical systems - Harnesses and connectors T7030, T7040, T7050, T7060, and T7070 The NAV II diagnostic connector is located under the cup Panel cover holder on the right-hand side of the cab: • Remove the panel cover (1) next to the rear right-hand post.
- Page 26 Electrical systems - Harnesses and connectors T7.170, T7.185, T7.200, T7.210, and T7.235 The NAV II diagnostic connector is located in the fuse 12-pin Deutsch connector panel on the right-hand interior rear wheel well. RAIL13TR03442BA NOTE: On some early machines, the transmit and receive pins were erroneously reversed at the factory.
- Page 27 Electrical systems - Harnesses and connectors CR9040, CR9060, CR9065, CR9070, CR9080, and CR9090 CX8070, CX8080, and CX9090 The NAV II diagnostic connector is wired directly into the 12-pin Deutsch connector 24-pin connector on the NAV II controller. RAIL13AF00009AA 47708311 05/12/2014 55.2 [55.100] / 9...
- Page 28 Electrical systems - Harnesses and connectors Guardian SP.240F, Guardian SP.275F, and Guardian SP.365F (After PIN YCYM00393) Guardian SP.240R and Guardian SP.275R (After PIN YCYM00404) The NAV II diagnostic connector is located underneath the Underneath the rear right-hand storage compartment rear right-hand storage compartment. RAIL13SP04560BA 47708311 05/12/2014 55.2 [55.100] / 10...
- Page 29 Index Electrical systems - 55 Harnesses and connectors - 100 Diagnostic connector - External view - NAV II diagnostic connector locations ....... 3 47708311 05/12/2014 55.2 [55.100] / 11...
- Page 30 47708311 05/12/2014 55.2 [55.100] / 12...
- Page 31 This as a preview PDF file from best-manuals.com Download full PDF manual at best-manuals.com...