Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DUP180Z
Summary of Contents for Makita DUP180Z
- Page 1 INSTRUCTION MANUAL Battery Powered Pruning Shears DUP180 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DUP180 Max. cutting capacity ø30 mm Overall length 296 mm (Shears part only) Rated voltage D.C. 18 V Net weight * 0.68 kg (Shears part only) • Due to our continuing program of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country. The weight according to EPTA-Procedure 01/2014 is shown in the table. Applicable battery cartridge and charger Battery cartridge BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B... -
Page 3: Declarations Of Conformity
SAFETY WARNINGS NOTE: The declared noise emission value(s) has been measured in accordance with a standard test method and may be used for comparing one tool with General power tool safety warnings another. NOTE: The declared noise emission value(s) may also be used in a preliminary assessment of WARNING Read all safety warnings, instruc- exposure. - Page 4 Personal safety Power tool use and care Stay alert, watch what you are doing and use Do not force the power tool. Use the correct common sense when operating a power tool. power tool for your application. The correct Do not use a power tool while you are tired or power tool will do the job better and safer at the under the influence of drugs, alcohol or med- rate for which it was designed.
-
Page 5: Additional Safety Instructions
Do not use a battery pack or tool that is dam- Never allow children, persons with reduced aged or modified. Damaged or modified batteries physical, sensory or mental capabilities or lack of experience and knowledge or people may exhibit unpredictable behaviour resulting in unfamiliar with these instructions to use the fire, explosion or risk of injury. - Page 6 Do not expose battery cartridge to water causing fires, personal injury and damage. It will or rain. also void the Makita warranty for the Makita tool and A battery short can cause a large current charger. flow, overheating, possible burns and even a breakdown.
-
Page 7: Parts Description
PARTS DESCRIPTION Fig.1 Shear blade Indicator lamps Angle adjustment button Main power button Battery cartridge Switch trigger Battery adapter Holster Waist belt (available in the market) 7 ENGLISH... -
Page 8: Functional Description
Installing or removing battery FUNCTIONAL cartridge DESCRIPTION CAUTION: Always switch off the tool before installing or removing of the battery cartridge. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed CAUTION: Hold the battery adapter and the before adjusting or checking function on the tool. -
Page 9: Indicator Lamps
Let the machine and battery(ies) cool down. 25% to 50% If no improvement can be found by restoring protection system, then contact your local Makita Service Center. 0% to 25% NOTICE: If the tool stops due to a cause... -
Page 10: Main Power Button
The meaning of indicator lamps is as follows: NOTE: This tool shifts to the standby mode when the switch trigger is not pulled for a certain period after Indicator lamps Description the tool is turned on. When the green indicator lamp is blinking, pull the switch trigger twice to return to the Blinking normal mode. -
Page 11: Cutting Depth Adjustment
Cutting depth adjustment ASSEMBLY After grinding or replacing the shear blades, adjust the cutting depth. To adjust the cutting depth, follow the CAUTION: Always be sure that the tool is steps below. switched off and the battery cartridge is removed before carrying out any work on the tool. Turn on the tool and pull the switch trigger twice to open the shear blades. - Page 12 Loosen the nut with the box wrench, and then NOTICE: When attaching the upper shear blade, remove it. make sure that the upper shear blade is placed in the direction shown in the figure. Turn over the tool, and then attach the nut to the tool and tighten it manually.
-
Page 13: Operation
OPERATION NOTICE: Tighten the bolts with the hex wrench in the upright position as shown in the figure. Tightening the bolts too much may damage the bolts. CAUTION: Always hold the tool firmly. And keep firm footing. CAUTION: Do not put any of your body parts near the shear blades during operation. -
Page 14: Maintenance
► 1 . Lubrication hole NOTICE: Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 14 ENGLISH... - Page 15 After the operation, remove dust from the shear blades with a wire NOTICE: The recommended tightening torque is brush. Wipe the shear blades off with a cloth. Then apply low-viscos- approximately 0.5 N•m. ity oil (machine oil, or spray-type lubricating oil) to the shear blades. Attach the bolt to the tool and tighten it with the hex wrench.
- Page 16 Lower shear blade Grinding the shear blades Grind the lower shear blade with the grinding NOTE: When grinding the shear blades, adding water stone in the direction of the arrow as shown in the to the grinding stone will make the grinding smoother. figure.
-
Page 17: Troubleshooting
TROUBLESHOOTING Before asking for repairs, conduct your own inspection first. If you find a problem that is not explained in the manual, do not attempt to dismantle the tool. Instead, ask Makita Authorized Service Centers, always using Makita replace- ment parts for repairs. State of abnormality Probable cause (malfunction) Remedy The shear blade does not move even The battery is low. - Page 20 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885A40-229 20230713...