Advertisement
Quick Links
204-0444-01
COMPONENTS 6MT
●
CD PLAYER 6MT H0010VC765
1
●
FITTING KIT 6MT H0010VC710
5
7
0
PF3982AD, PF3982AE, PF3982BD, PF3982BE
Applicable model
WRX(6MT) 2022MY~
WRX(CVT) 2022MY~
2
3
4
6
8
9
!
Genuine component number
H0010VC785
H0010VC775
No.
1
CD PLAYER
2
Relay harness
3
Cable tie
4
Urethane sheet
No.
5
Panel deck
6
Pocket (for deck)
7
Mat
8
Truss screws (M5x6)
9
Screws (M5x16)
0
Bracket RH
!
Bracket LH
- 1 -
Name
Qty
1
1
10
2
Name
Qty
1
1
1
4
6
1
1
△
1
Advertisement
Related Manuals for Subaru H0010VC785
Summary of Contents for Subaru H0010VC785
- Page 1 △ 204-0444-01 Applicable model Genuine component number WRX(6MT) 2022MY~ H0010VC785 WRX(CVT) 2022MY~ H0010VC775 COMPONENTS 6MT ● CD PLAYER 6MT H0010VC765 Name CD PLAYER Relay harness Cable tie Urethane sheet ● FITTING KIT 6MT H0010VC710 Name Panel deck Pocket (for deck)
-
Page 2: Tools Used
COMPONENTS CVT ● CD PLAYER CVT H0010VC755 Name CD PLAYER Relay harness Cable tie ● FITTING KIT CVT H0010VC700 Name Panel deck Pocket (for deck) Truss screws (M5x6) Screws (M5x16) Plastic clips Spring nuts Bracket RH Bracket LH TOOLS USED Philips screwdriver, Flathead screwdriver, Clip remover, Trim removal tool, Nose pliers, Nipper, Cutter knife, Plastic tape, Curing tape - 2 -... - Page 3 PRECAUTIONS • Please refer to the precautions below before you begin work, in order to install the product safely and accurately Please also refer to the vehicle Service manual. • This manual shows typical installation procedures on LHD vehicle. Installation will be mirror image for RHD vehicles. ATTENTION •...
-
Page 4: Installation Overview
WARNING To prevent any accident during work, make sure to disconnect the negative (- ) terminal of the battery according to the latest service manual. INSTALLATION OVERVIEW Vehicle-side pre-wire(Video system) Relay harness CD PLAYER Vehicle-side pre-wire(Power system) Vehicle-side pre-wire(Video system) Relay harness CD PLAYER Vehicle-side pre-wire(Power system) - Page 5 REMOVING THE VEHICLE COMPONENTS NOTE Affix curing tape to the shaded parts ( ) in the figure to protect the vehicle. (1) Rotate the shift knob in the direction of the arrow to remove it. Shift knob (2) Remove the shift lever boot ASSY. (Clips: 8 points) Shift lever boot ASSY Clips...
- Page 6 (3) Remove the parking brake boot. (Clips: 5 points, Tab: 1 point) Clips Parking brake boot (4) Remove the cover front ASSY. (Clips: 12 points) Clips Cover front ASSY Connector position (5) Remove the two cap consoles. Cap console (6) Remove the two bolts. Bolt Moving forward Bolt...
- Page 7 (7) Remove the screw, disconnect each connector, and remove the console box Screw ASSY. (Clips: 3 points) Console box ASSY Clips Connector position (8) Remove the screw, and then remove the cover center side RH. Clips (Clips: 2 points) Screw Cover center side RH - 7 -...
- Page 8 NOTE Affix curing tape to the shaded parts ( ) in the figure to protect the vehicle. (1) Turn over the rubber of the center tray, insert the screwdriver into the position in the figure, Screwdriver Shift lever and while inserting it to the depth, lower the shift lever.
- Page 9 Caution during reinstallation ● If the plastic panel is detached from the rubber during removal of the center tray, firmly fit the hooks of the rubber into the recess sections of the plastic panel, and perform reinstallation. Rubber of the Center tray Plastic panel Hooks of the rubber...
- Page 10 (5) Remove the two points of the cap console. Screws Cap console (6) Remove the two bolts and two screws, and Bolt while disconnecting the three connectors, Connectors remove the console box ASSY. (Tabs: 2 points) Bolt Cap console Console box ASSY Tabs (7) Remove the screw, and then remove the cover center side RH.
- Page 11 EXCHANGING TO THE CONSOLE BOX ASSY POCKET (FOR DECK) (1) Remove the existing harness. Existing harness (Clips: 7 points) NOTE Clips For section A in the figure, use nose pliers to hold the clips and remove them. Removal of the clip at section A Existing harness Nose pliers Console box ASSY...
- Page 12 (4) Remove the three screws, and then remove the lid ASSY. Screws Lid ASSY Console box ASSY (5) Remove the two screws, and then remove Screw the console box RH in the order of 1 and 2 . Console box LH (Clips: 4 points) Screw * Remove the console box LH in the same...
- Page 13 (6) Remove the socket from the existing pocket, Remove and attach it to the pocket (for deck). Socket Socket Existing pocket Pocket(for deck) (7) Use the four truss screws (M5x6) Truss screws (M5x6) to attach the bracket RH and Bracket LH bracket LH to the CD PLAYER.
- Page 14 (8) Install the CD PLAYER while passing the CD PLAYER CD PLAYER cable through the hole in the pocket (for deck). Pocket(for deck) (9) Use the four screws (M5x16) to fix the CD PLAYER to the pocket (for deck). CD PLAYER Pocket(for deck) - 14 -...
- Page 15 (10) Fix the clip of the CD PLAYER cable into CD PLAYER the existing holes in the pocket (for deck). Front side Existing hole Pocket(for deck) Fix the clip CD PLAYER cable (11) Fix the two CD PLAYER cable connectors Pocket(for deck) into the existing holes in the pocket (for deck).
- Page 16 (15) Assemble the console box ASSY using the reverse procedure to removal. CD PLAYER Console box ASSY (16) Turn over the console box ASSY, peel off Console box ASSY the vinyl tape from the existing harness, and then remove the L-shaped stay with clip. Vinyl tape Stay with clip Vinyl tape...
- Page 17 (17) Aligning with the end of the sponge of existing harness, attach the two urethane sheets and fold them back. Urethane sheet (attach one sheet) Fold back Align Urethane sheet Align Existing harness (align the length and cut) (18) Use a cable tie to fix the indicated position of the existing harness to the pocket (for deck).
- Page 18 (1) Remove the existing harness. Existing harness Remove the clip at this position (Clips: 8 points) from the exterior. Clips NOTE Use nose pliers to pinch the six clips on the existing harness and release them. Release the two clips shown by the arrows in the figure from the exterior of the console box ASSY.
- Page 19 (3) Remove the four screws, and then remove the lid ASSY. Lid ASSY Screws Console box ASSY (4) Remove the two screws, and then remove Screw the console box RH in the order of 1 and 2 . Console box LH Screw (Clips: 5 points) * Remove the console box LH in the same...
- Page 20 (6) Attach the four spring nuts to the pocket Spring nuts (for deck). Front side Pocket (for deck) Spring nuts (7) Use the four truss screws (M5x6) Truss scews (M5x6) Bracket LH to attach the bracket RH and bracket LH to the CD PLAYER. Bracket RH CD PLAYER Truss scews (M5x6)
- Page 21 (9) Use the four screws (M5x16) to fix the CD PLAYER to the pocket (for deck). Scews (M5x16) Scews (M5x16) CD PLAYER Pocket (for deck) (10) Fix the two CD PLAYER cable connectors into the existing holes in the pocket (for deck).
- Page 22 (13) Install six plastic clips to the panel deck. Plastic clips Plastic clips Panel deck (14) Install the panel deck to the pocket Panel deck (for deck). Clips Pocket (for deck) (15) Assemble the console box ASSY using the reverse procedure to removal. CD PLAYER Console box ASSY - 22 -...
- Page 23 WIRING OF RELAY HARNESS (1) Connect the connector with the black connection side of the relay harness to the vehicle-side pre-wire connector. NOTE Vehicle-side pre-wire To prevent damage to the vehicle-side connector(4pole) connector, make sure not to connect the gray-surface connector of the relay harness.
- Page 24 (3) Peel off the vinyl tape and take out the white 5P connector of the existing harness. Connector of the existing harness (White 5P connector) Peel off the vinyl tape (4) Connect the white 5P connector of the Connector of the CD PLAYER Console box ASSY existing harness to the white 5P connector (White 5P connector)
- Page 25 (6) Connect the relay harness to the gray 4P connector of the CD PLAYER. NOTE To prevent damage to the vehicle-side connector, make sure not to connect the Connect the connector Relay harness black-surface connector of the relay with the gray side harness.
- Page 26 (8) After reinstalling the vehicle components, attach the mat in the console box ASSY. CD PLAYER - 26 -...
- Page 27 (1) Connect the connector with the black connection side of the relay harness to the vehicle-side pre-wire connector. NOTE To prevent damage to the vehicle-side connector, make sure not to connect the Vehicle-side pre-wire connector(4pole) gray-surface connector of the relay harness.
- Page 28 (4) Connect the connectors of the relay harness and vehicle-side pre-wire to the CD PLAYER cable connectors. NOTE CD PLAYER cable Connect the connector To prevent damage to the vehicle-side connector (Gray 4P) with the gray side connector, make sure not to connect the black-surface connector of the relay harness.
-
Page 29: Wiring Diagram
WIRING DIAGRAM CD PLAYER Connector (White 5P) Vehicle-side pre-wire (power system) Relay harness Must be gray Must be black connection surface connection surface Connector (Gray 4P) Vehicle-side pre-wire (video system) Operation Check (1) Referring to the wiring diagram, connect all wires. (2) Connect the battery, and turn on the engine switch. -
Page 30: Revision History
REVISION HISTORY △ Content Date △ Newly established 10 / 2021 △ Part number change 8 / 2023 △ △ - 30 -...