Intended use Timer programming ... . . 23 Intended use End of programme ....24 Automatic switch off / interior light . . 24 I n t e n d e d u s e This appliance is intended for...
Safety instructions Delivery The electrical connection conditions must correspond 1. Check the packaging and with the specifications dishwasher immediately for on the dishwasher rating plate 9:. damage caused in transit. Do not switch on a damaged If the power cord of this appliance, but contact your appliance is damaged, supplier.
Safety instructions If you cannot obtain any In daily use information from Read and observe the safety the manufacturer, you must information and instructions not install the dishwasher for use on the packaging above or below these for cleaning and rinsing agents. appliances.
Safety instructions Disposal Warning Risk of explosion! 1. Make redundant appliances Do not add any solvents unusable to prevent to the washing chamber. subsequent accidents. Danger of explosion! 2. Dispose of the appliance in a n environmentally friendly Warning manner. Risk of scalding! Warning Open the door carefully when...
Protection of the environment Ensure that children do not Protection of the place fingers in the tablet environment collecting tray 1:. Small fingers could become i o n P r o t e c t o f t e n v i r o n m e n t caught in the slots.
Getting to know your appliance Appliance interior Getting to know your appliance 1" Interior light * G e t t i t o k n o w y o u r a p p l i a n c 1* Top basket Diagrams of the control panel 12 Knife shelf * and the interior of the appliance can be...
Water softening system/Special salt To change the setting: Water softening 1. Press programme button 3. system/Special salt Each time the button is pressed, the set value increases by one level; W a t e r s o f t e n i s y s t e m / S p e c i s a l t when the value of :...
Water softening system/Special salt Using special salt Using detergents with salt component D e t e r g e n t s w i t h s a l t c o m p o n e n t Always refill with special salt immediately before switching on the If combined detergents with a salt appliance.
Rinse aid 2. Carefully pour rinse aid up Rinse aid to the max. mark in the filler opening. R i n s e a i d As soon as the rinse-aid refill indicator H is lit on the fascia, there is still a rinse-aid reserve of 1-2 rinsing processes.
Utensils 5. Press programme button # until Utensils the factory set value : indicated on the digital display h. U t e n s i To change the setting: Not suitable 1. Press programme button 3. Each time the button is pressed, the Cutlery and utensils made of wood.
Utensils Loading the dishwasher Cups and glasses Top basket 1* 1. Remove large food remnants. It is not necessary to prerinse utensils under running water. 2. Place the utensils so that – they are secure and cannot tip over. – all utensils with their openings face down.
Utensils E tagere * E t a g e r e Heavily soiled utensils (pans) should be placed in the bottom basket. The The etagere and the space underneath more powerful spray jet provides can be used for small cups and glasses a better dishwashing result.
Utensils Small accessories holder * A djusting the height of the S m a l l a c c e s s o r i e s h o l d e r A d j u s t i n g t h e h e i g h t o f t h e b a s k e t basket * * depending on model Light-weight plastic accessories, e.g.
Detergent Top basket with side levers Detergent 1. Pull out the top basket 1* out. D e t e r g e You can use tablets as well as powder 2. To lower the basket, press in the left or liquid detergents for dishwashers, but and then the right lever on the never use washing up liquid.
Detergent Adding detergent 2. Close the cover on the detergent dispenser by sliding it up until the lock engages without difficulty. 1. If the detergent dispenser 9* is still closed, press the lock 92 to open the detergent dispenser. Pour detergent into the dry detergent dispenser 9* only (insert tablet flat, not on its edge).
Detergent Combination detergent Notes You will obtain optimum rinsing Apart from conventional detergents and drying results by using solo (Solo), a number of products are offered detergents and applying salt with additional functions. These and rinse aid separately. products contain not only the detergent If programmes are short, tablets but also rinse-aid and salt replacement may not have full cleaning effect...
Overview of programmes Overview of programmes p r o g r a m m e s O v e r v i e w o f The max. possible number of programmes is illustrated in this overview. The corresponding programmes and their arrangement can be found on the fascia.
Additional options § Programme selection Half load * H a l f l o a d You can select a suitable programme If you have only a few items to wash according to the type of utensils and (e.g. glasses, cups, plates), you can degree of soiling.
Operating the appliance Switching on the appliance Operating the appliance 1. Turn on the tap fully. 2. Open the door. O p e r a t i i a n c e t h e a p p l 3. Switch on ON/OFF switch (. Programme data The Eco 50°...
Operating the appliance 7. Press START button `. Optical display while The set value is saved. the programme is running * O p t i c a l d i s p l a y w h i l e t h e p r o g r a m m e i s r u n n i n g 8.
Operating the appliance End of programme Automatic switch off after end of programme or interior light* A u t o m a t i c s w i t c h o f f / i n t e r i o r l i g h t The end of the programme O / : displayed on the floor –...
Operating the appliance To change the setting: Interrupting the programme 1. Press programme button 3. 1. Open the door. Each time the button is pressed, 2. Switch off ON/OFF switch (. the set value increases by one level; when the value of : has been The LEDs go out.
Cleaning and maintenance Changing the programme Cleaning and maintenance When the START button ` has been pressed, the programme cannot be C l e a n i a n d m a i n t e n a n c e changed.
Cleaning and maintenance Warning – Health hazard 3. Remove any residue and clean filters under running water. Never use other domestic detergents, e.g. containing chlorine! 4. Re-install filter system in reverse sequence and ensure that the arrow marks are opposite each other after Special salt and rinse aid closing the filter system.
Fault, what to do? In this case: Fault, what to do? 1. First always disconnect F a u l t , w h a t d o ? the appliance from the power supply. Experience has shown that you can 2.
Fault, what to do? Fault table Fault Cause Remedial action “Check water supply” Supply hose kinked. Install supply hose without kinks. display 8 lights up. Tap turned off. Turn on the tap. Tap jammed or calcified. Turn on the tap. Flow rate must be min.
Page 30
Fault, what to do? Fault Cause Remedial action A different error code is A technical fault has probably Switch off appliances with the ON/OFF switch (. After a short time restart indicated on the digital occurred. display. the appliance. to : If the problem recurs, turn off the tap and pull out the mains plug.
Page 31
Fault, what to do? Fault Cause Remedial action Utensils not dry. No or too little rinse aid Refill rinse aid. in the dispenser. Programme selected without Select programme with drying (see drying. Overview of programmes, Programme sequence). Water collecting in depressions Arrange utensils in a sloping position, on the utensils and cutlery.
Page 32
Fault, what to do? Fault Cause Remedial action Food remnants Utensils placed too closely Arrange utensils with adequate clearance on the utensils. together, utensils basket between them ensuring that the spray jets overfilled. can reach the surface of the utensils. Prevent contact points.
Page 33
Fault, what to do? Fault Cause Remedial action Water stains on plastic Droplet formation on plastic Use a more intensive programme (more parts surface is physically unavoidable. water changes). After drying, water stains are Arrange utensils in a sloping position. visible.
Page 34
Fault, what to do? Fault Cause Remedial action Coloured (blue, yellow, Film formation consisting Can be partly removed with machine brown), difficult to remove of ingredients from vegetables cleaner or by mechanical cleaning. Coatings to non-removable coatings (e.g. cabbage, celery, potatoes, are harmless.
Page 35
Fault, what to do? Fault Cause Remedial action Rust spots on the cutlery. Cutlery not adequately rust- Use corrosion-resistant cutlery. resistant. Knife blades are frequently more severely affected. Cutlery will also rust if rusting Do not wash rusting parts. parts are rinsed at the same time (pan handles, damaged utensil baskets, etc.).
Page 36
Fault, what to do? Fault Cause Remedial action Appliance stops Door not closed properly. Close the door. in the programme or Do not place utensils or fragrance Check whether rear panel is being pressed programme is interrupted. dispenser in the tablet collecting in, e.g.
Customer service Customer service Installation and connection C u s t o m e r s e r v i c e If you are unable to rectify the fault, l a t i o n I n s t a l a n d c o n n e c t i please contact your customer service.
Installation and connection Delivery Installation Your dishwasher has been checked The required installation dimensions can thoroughly in the factory to ensure that it be found in the installation instructions. is in working order. This may cause Level the appliance with the aid of the small water stains.
Installation and connection Drinking water connection Setting hot water: 1. Open the door. 2. Switch on ON/OFF switch (. 1. Fasten the drinking water connection to the tap according 3. Hold down programme button # to the installation instructions using and press START button ` the enclosed parts.
Installation and connection A power cord extension may be Transportation purchased from customer service only. Empty the dishwasher and secure loose Use only a residual current operated parts. circuit-breaker which features Drain the appliance according to the the symbol ‚. Only this extension following steps: guarantees compliance with 1.
Page 42
*9000795865* 9000795865 en (9311) 640MV...