Craftsman BRUSHWACKER C944.514560 Instruction Manual
  1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Trimmer
  5. BRUSHWACKER C944.514560
  6. Instruction manual
Craftsman BRUSHWACKER C944.514560 Instruction Manual

Craftsman BRUSHWACKER C944.514560 Instruction Manual

Gasoline, 32cc / 1.9 cu.in. 2-cycle
Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
Instruction Manual
32cc / 1.9 cu.in. 2-Cycle
GASOLINE BRUSHWACKER
Model No.
C944.514560
S S S S Safety
S S S S Assembly
S S S S Operation
S S S S Maintenance
S S S S Parts List
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating
Instructions before first use of this product.
Sears Canada, Inc., Toronto, Ontario M5B 2B8
530164843
3/22/04
r

Advertisement

Table of Contents
loading

Related Manuals for Craftsman BRUSHWACKER C944.514560

Summary of Contents for Craftsman BRUSHWACKER C944.514560

  • Page 1 Instruction Manual 32cc / 1.9 cu.in. 2-Cycle GASOLINE BRUSHWACKER Model No. C944.514560 S S S S Safety S S S S Assembly S S S S Operation S S S S Maintenance S S S S Parts List For Occasional Use Only...

  • Page 2: Table Of Contents

    Storage Troubleshooting Table Emissions Statement Parts List Center Section Parts and Ordering Back Cover R R R R CRAFTSMAN GAS POWERED allow limitations on how long an INSTRUCTION SAFETY INFORMATION MANUAL ON THE UNIT DANGER: Blade can thrust vio- lently away from material it does not cut.
  • Page 3 S Maintain unit according to recom- mended procedures. Keep blade sharp. Keep cutting line at proper length. S Use only Craftsman! replacement line. Never use wire, rope, string, etc. S Install required shield properly be- fore using the unit. Use the metal shield for all metal blade use.
  • Page 4 S Keep others away when making car- buretor adjustments. S Use only recommended Craftsman accessories and replacement parts. S Have all maintenance and service not explained in this manual per- formed by a Sears Service Centre.

  • Page 5: Assembly

    If you operate in a locale ASSEMBLY CARTON CONTENTS Check carton contents against the fol- lowing list. Model C944.514560 S Powerhead S Lower attachment (with trimmer head installed) S Cupped washer S Large nut for installing blades...
  • Page 6 For optional attachments, see the section of the applicable at- SEMBLY tachment instruction manual. ATTACHING THE HANDLEBAR DANGER: To avoid serious inju- ry, the barrier portion of the handlebar must be installed as shown to provide a barrier between operator and the spinning blade.
  • Page 7 NOTE: Remove the trimmer head and plastic shield before attaching the metal shield and installing the weed blade. To remove the trimmer head, align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup.
  • Page 8 THE CUTTING HEAD ATTACHING for illustrations. Be THE PLASTIC SHIELD sure to store all parts and instructions for future use. Never use the trimmer head with the metal blade installed. ATTACHING THE METAL SHIELD WARNING: The metal shield must be properly installed on the tool anytime the tool is used with a blade.

  • Page 9: Operation

    Remove fuel cap slowly when refueling. This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled en- gine oil. We recommend Craftsman brand synthetic oil. Mix gasoline and oil...
  • Page 10 40:1. A 40:1 ratio is ob- tained by mixing 3.2 ounces (95 ml) of oil with 1 gallon (4 litres) of unleaded gasoline. Included with this trimmer is a 3.2 ounce (95 ml) container of oil. Pour the entire contents of this container into 1 gallon (4 litres) of gasoline to achieve the proper fuel mixture.
  • Page 11 C944.514610 WARNING: Always stop unit and disconnect spark plug before re- moving or installing attachments. REMOVING TRIMMER ATTACH- MENT (OR OTHER OPTIONAL AT- TACHMENTS) CAUTION: When removing or instal- ling attachments, place the unit on a flat surface for stability.
  • Page 12 S Operate the engine at full throttle. S Hold the trimmer head parallel to and above the grassy area. S Tap the bottom of the trimmer head lightly on the ground one time. Approximately 2 inches (5 cm) of line will be advanced with each tap.
  • Page 13 S For mowing or sweeping, use full throttle for a good clean job. TRIMMING -- Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.
  • Page 14 stop for an instant and then sud- denly move or “thrust” away from the object that was hit. The “thrust- ing” reaction can be violent enough to cause the operator to be propelled in any direction and lose control of the unit. The uncon- trolled unit can cause serious in- jury if the blade contacts the op- erator or others.
  • Page 15 ADDITIONAL SAFETY RULES FOR OPTIONAL ATTACHMENTS WARNING: For each optional attachment used, read entire instruc- tion manual before use and follow all warnings and instructions in manual and on attachment. WARNING: Ensure handlebar remains installed on upper shaft (en- gine end of unit) at all times. Handlebar EDGER SAFETY WARNING:...
  • Page 16 The tines be- come very sharp from use. S Do not run unit at high speed unless cultivating. HEDGE TRIMMER SAFETY DANGER: RISK OF CUT; KEEP HANDS AWAY FROM BLADE -- Blade moves momentarily after the trigger is released.
  • Page 17 WARNING: To prevent serious injury, do not use more than one boom extension with a pole pruner attach- ment. WARNING: Keep the pruner away from power lines or electrical wires. S Only use for pruning limbs or branches up to 4 inches in diameter. S Do not operate the unit faster than the speed needed to prune.

  • Page 18: Maintenance

    MAINTENANCE MAINTENANCE SCHEDULE WARNING: Disconnect the spark plug before performing maintenance except for carburetor adjustments. CARE & MAINTENANCE TASK Check for loose fasteners and parts Check for damaged or worn parts Inspect and clean unit and labels Clean air filter Inspect muffler and spark arresting screen Replace spark plug GENERALRECOMMENDATIONS...

  • Page 19: Service & Adjustments

    5. Replace with a pre-wound spool, or cut two lengths of 12-1/2 feet (3.8 meters) of 0.080" (2 mm) diameter Craftsman! brand line. WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

  • Page 20: Storage

    Run engine at least 5 min- utes after adding stabilizer. Craftsman 40:1, 2-cycle engine oil (air cooled) is already blended with fuel stabilizer. If you do not use this Sears oil, you can add a fuel stabilizer to your fuel tank.

  • Page 21: Troubleshooting Table

    TROUBLESHOOTING TABLE WARNING: Always stop unit and disconnect spark plug before perform- ing all of the recommended remedies below except remedies that require operation of the unit. TROUBLE CAUSE Engine will not 1. ON/OFF switch in start. OFF position. 2. Engine flooded. 3.

  • Page 22: Emissions Statement

    U. S. EPA / ENVIRONMENT CANADA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS: The U. S. Environ- mental Protection Agency/Environ- ment Canada and Sears Canada, Inc., are pleased to explain the emis- sions control system warranty on your year 2002--2004 small off--road engine.
  • Page 23 replacement part used in the perfor- mance of any warranty maintenance or repair on emission related parts will be provided without charge to the owner if the part is under warranty. EMISSION CONTROL WARRANTY PARTS LIST: Carburetor, Ignition System: Spark Plug The information on the product label indicates which standard your engine is certified.

Table of Contents