Specifications; Dimensions - Yamaha P2075 Operating Manual

SPECIFICATIONS
POWER OUTPUT LEVEL
(STEREO) БОМ + БОМ Ві = B8ohms, f 2 20Hz to 20kHz, THD 0.0596
75W+75W RL= 4ohms, f=20Hz to 20kHz, THD 50.1%
(BTL-MONO) 100W Ве = 16ohms, f - 20Hz to 20kHz, THD x 0.05%
150W RL= 8ohms, # = 20Hz to 20kHz, THD x 0.196
FREQUENCY RESPONSE
+0, – 198, += 10Hz to ЗОКН2, В. = 8ohms, PO=1W
POWER BAND WIDTH (THD xO.196)
(STEREO) 10Hz to 50kHz PO=25W, RL= 8ohms, 10Hz to 50kHz
Ро = 38W, ВЕ = 4ohms .
(BTL-MONO) 10Hz to 30kHz РО = 50W, RL = 16ohms, 10Hz to 30kHz
Po=75W, RL= 8ohms
TOTAL HARMONIC DISTORTION
(STEREO) =0.01% Po=25W, f= 1kHz, RL=8ohms
<0.05% PO=25W, f - 20Hz to 20kHz, RL=8ohms
€0.0196 РО = 38W, f= 1kHz, ВЕ = 4ohms
=0.05% Ро -238W, Ғ= 20Hz to 20kHz, ВІ = 4ohms
(BTL-MONO) =0.01% Ро = 50W, f=1kHz, ВЕ = 16ohms
<0.05% PO = 50W, {= 20Hz to 20kHz, АЕ = 16ohms
50.01% Ро = 75W, f = 1kHz, Ві = 8ohms
<0.05% PO = 75%, {= 20Hz to 20kHz, RL=8ohms
INTER MODULATION DISTORTION (70Hz: 7kHz = 4; 1)
(STEREO) <0.05% РО > 25У, RL=8ohms, 50.05% PO=38W,
RL =4ohms
(BTL-MONO) 30.05% Ро -«50W, ВІ = 16ohms, =0.05% PO=75W, -
ВЕ 28ohms
CHANNEL SEPARATION (INPUT Short, АТТ Max., RL = 8ohms,
Po = – 3dB point from nominal power)
> ВОЧВ += 1kHz
2100 f=1kHz, Аі = 8ohms, 270 += 20Н2 to 20kHz, ВЕ = 8ohms
DAMPING FACTOR
2100 f=1kHz, RL=8o0hms, z 70
SIGNAL TO NOISE
(STEREO) 2100dB INPUT Short @ 12.7kHz LPF
=105dB INPUT Short @ IHF-A Network
(BTL-MONO) = 9598 INPUT Short @ 12.7kHz LPF
z100dB INPUT Short @ IHF-A Network
SLEW RATE
(STEREO) 14V/usec. RL= 8ohms, Full Swing
(BTL-MONO) 26V/usec. RL = 16ohms, Full Swing
SENSITIVITY
+ 4dBm (1.23V rms) РО = 75W, ВЕ = 4ohms, АТТ Max.,
VOLTAGE GAIN
23.0dB += kHz, RL = 4ohms, АТТ Мах.
f-1kHz
INPUT IMPEDANCE
= 15kohms, Balanced or unbalanced
RESIDUAL NOISE
>_ 78dBm АТТ Min.,
IHF-A Network
INDICATORS
Signal: Green LED f = 20Hz to 20kHz, Voz 2V Clipping: Red LED THD > 1%
Protection: Red LED during the protection or muting is on.
Protection: 260°C Heat sink Temperature
Pilot: Red LED Power ON
PROTECTION CIRCUITS
Muting: 62- 2sec. After Power ON DC sense: DC + 2V Output Voltage
Thermal: 285°C Heat sink temperature (General model)
PC limiter: ON RL = = 20hms
CONTROLS
Front: 2x31 step INPUT Attenuator, Push ON/Push OFF POWER switch.
Rear : MONO/STEREO
MODE switch, IN/OUT Transformer switch,
Voltage Selector switch (General mode! only)
POWER REQUIREMENTS
General model
U.S. & Canadian models
0 12.7kHz, LPF = ~ 86dBm АТТ Min.,
220/240V AC, 50/60Hz
120V AC, 60HZ
POWER CONSUMPTION
General model
U.S. & Canadian models
WEIGHT
9.5 kg (20.9 Ibs)
DIMENSIONS (W x H x D)
480 x 98 x 364 (18-7/8" x 3-7/8" x 14-3/8"]
ACCESSORIES
Rubber caps to discourage unauthorized or accidental changes in setting of
input attenuators (included).
400\/
250W, 300VA
* All specifications subject to change without notice.
DIMENSIONS
422016-5/8)
25(17
| — à
364(14-3/8)
299.4(11-3/4)
464/8)
372(4-5/8) |
5(1-3/8)
=f
88(3-1
98(3-7/8')
480(18-7/8')
(3/8)
Unit: mm (Inch)
32