Table of Contents
Advertisement
Available languages
Available languages
English
Proper hand position requires one hand on the main
handle
18
and one hand on the secondary handle
Installing and Removing the Battery Pack
(Fig. K)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack is
fully charged.
1. To install the battery pack
the battery pack with the rails inside the tool's handle
and slide it into the handle until the battery pack is firmly
seated in the tool and ensure that it does not disengage.
2. To remove the battery pack from the tool, press the
battery pack release button
battery pack out of the tool handle. Insert it into
the charger as described in the charger section of
this manual.
Variable Speed Wheel (Fig. L)
The variable speed wheel
of the tool to the workpiece material.
Use a low speed setting when using a fine grit, when
working with plastics or ceramics and when removing
painted or varnished surfaces.
Use a high speed setting when using a coarse grit and when
removing a lot of material.
•
Set the variable speed control wheel
required setting.
Switching On and Off (Fig. A)
1. To switch the tool on, press the variable speed switch
2. To switch the tool off, release the variable speed switch.
3. For continuous operation:
a. Press the variable speed switch
b. Press the lock‑on button
c. Release the variable speed switch.
4. To switch the tool off when in continuous operation,
press and release variable speed switch.
Lock‑off Button (Fig. A)
WARNING: To prevent accidental start‑up, this tool is
equipped with a lock‑off button.
1. To lock the tool, depress the lock‑off button
locked position. When the lock‑off button is in the
locked position, the tool is locked and the variable speed
switch
cannot be pulled.
2
2. To unlock the tool, depress the lock‑off button
unlocked position.
Special Applications (Fig. M–P)
WARNING: To reduce the risk of fire or serious injury,
avoid sanding ignitable materials such as aluminum
and magnesium.
WARNING! DO NOT allow bystanders in front of the
tool while in operation as there may be a risk of the
sanding belt breaking and dislodging from the arm.
12
9
into the tool handle, align
and firmly pull the
10
allows you to adapt the speed
1
1
to the
.
2
4
.
3
Straight Arm (Fig. N–P)
5
.
•
Use the normal or narrow arms for general use, for
slotting and for making joints.
•
Use section A for general sanding and in confined areas.
Offset Arm (Fig. M)
Where supplied
•
Use section B for curved surfaces.
Hints for Optimum Use
•
Always hold the tool with both hands.
•
Do not exert too much pressure on the tool.
•
Regularly check the condition of the sanding belt
Replace when necessary.
•
Always sand with the grain of the wood.
•
When sanding new layers of paint before applying
another layer, use extra fine grit.
•
Consult your retailer for more information on
available accessories.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
2
.
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those
to the
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this product
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
3
to the
with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN. Call 1-888-331-4569.
.
14
Advertisement
Table of Contents
