1. Manuals
  2. Brands
  3. Briggs & Stratton Manuals
  4. Brush Cutter
  5. NAX 600B
  6. Manual

Briggs & Stratton NAX 600B Manual

Hide thumbs Also See for NAX 600B:
Table of Contents

Advertisement

Quick Links

Download this manual
NAX 600B

Advertisement

Table of Contents
loading

Related Manuals for Briggs & Stratton NAX 600B

Summary of Contents for Briggs & Stratton NAX 600B

  • Page 1 NAX 600B...
  • Page 3 BRUSHCUTTER Model: NAX 600B...
  • Page 4 CONSTRUCTION OF BRUSHCUTTER AND ILLUSTRATIVE DRAWINGS Fig. 1 Fig. 2 Fig. 3...
  • Page 5 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12 Fig. 13 Fig. 14 Fig. 15...
  • Page 6 Fig. 16 Fig. 17 Fig. 18 Fig. 19...
  • Page 7 Fig. 20...
  • Page 8 Fig. 21...

  • Page 9: Table Of Contents

    Original operation manual, edition 1/2020 Translation of the original operation manual from polish language This manual should be treated as an integral part of the device. It should be stored in the place provided for it so that it is easily accessible.

  • Page 10: Technical Data

    TECHNICAL DATA Brushcutter NAX 600B Type, model TT-1E40F-5 BS series Engine 40: 1 (4l of gasoline for every 100 ml of two-stroke oil) Fuel mix 42.7 cc Engine capacity 1.2 kW - 7500 rpm Machine rated power 1.8 Nm - 5500 rpm...

  • Page 11: Safety Rules For Machines And Devices With Internal Combustion Engine

    Note: Disconnect the high-voltage pipe from the spark plug before maintenance and / or repair. Risk of fire or explosion. Gasoline is highly flammable. 10. Note: A hot surface can cause burns. 11. Note: Exhaust gases are harmful to health. There is a danger of poisoning or suffocation. Do not use the device indoors. 12.
  • Page 12 SAFETY DURING WORKING WITH FUEL  The internal combustion engine is designed to run on gasoline or a fuel mixture (see type of fuel in the device's technical data).  Gasoline should be stored only in specially prepared containers (canisters). ...

  • Page 13: Detailed Safety Regulations

    USE AND CARE FOR EQUIPMENT  Do not overload the tool. Use a tool with the power appropriate for the work. Properly selected equipment will enable better and safer work under the load for which it was designed.  Store the unused equipment out of the reach of children. Do not allow people not familiar with the tool or this manual to use the equipment.
  • Page 14  the cutting tool and the whole cutting unit (three-armed knife or head with a cutting line, fastening elements, construction of the cutting unit) are in good technical condition; regularly check their attachment, damage and wear (depressions, cracks),  safety devices (e.g. cover, housing, handle, levers) are in good technical condition and work properly. ...
  • Page 15  Correct posture during work is important, so as not to over-bother, frequent change of work position is recommended.  Stop work every 15 minutes - rest is necessary. Tiredness and distraction can contribute to an accident.  Keep your feet steady and keep balance during work. ...

  • Page 16: Safety And Liability Of The Manufacturer

    In the event of a fault, stop / turn off the machine and contact an authorized service center to rectify the fault. SAFETY AND PRODUCER'S LIABILITY Any use of the brushcutter, other than described in this manual is considered improper and the manufacturer is not liable for any damage or damages resulting from such a procedure.

  • Page 17: Preparing For Work

    PREPARING FOR WORK The brushcutter is delivered by the manufacturer in a cardboard packaging partially disassembled. After reading the operating instructions and assembly drawings, assembling the brushcutter should not be too difficult. All necessary components for assembly are included in the packaging. OPERATION CONSTRUCTION OF BRUSHCUTTER Illustrative drawings can be found on page 4, Fig.

  • Page 18: The Staring

    ASSEMBLY OF THE THREE-ARM KNIFE Unscrew the cap (Fig. 7) the nut is unscrewed clockwise. Remove the washer from the pressed sheet metal (Fig. 8) remove the spacer (Fig. 9). We proceed to mount the three-armed knife. Mount the three-armed knife on the shaft of the drive shaft (Fig. 11). Attach the washer from the pressed sheet metal (Fig.
  • Page 19 mixture, first pour gasoline into a special container (canister), then oil and mix. It is recommended to use the special container included in the set, in which the amount of gasoline and the amount of oil to be added are marked. The whole should be mixed thoroughly.

  • Page 20: Maintenance

    MAINTENANCE The rules for safe maintenance of the device are described in this manual in the section "Maintenance and storage" in the chapter "Detailed safety rules for brushcutters". WARNING! Before cleaning, inspecting or repairing the device, make sure that the engine is switched off and is not hot. Disconnect the spark plug to prevent the brushcutter from being switched on accidentally.

  • Page 21: Problems Review And Diagnosis

     Before transporting the brushcutter, if the cutting attachment is a three-armed knife, replace the cover.  Carry the brushcutter by holding it firmly and remembering its dimensions.  When transporting the brushcutter, secure it so that the propeller shaft tube does not deform. ...

  • Page 22: Warranty And Service

    WARRANTY AND SERVICE The product purchased by you is intended for amateur (hobby) use only. If the equipment is used for other purposes (commercial, professional), it will lose the guarantor's liability for the purchased equipment. You can find information on the warranty and the NAX service network in the attached warranty card.

  • Page 24: Declaration Of Conformity

    DECLARATION OF CONFORMITY        ...
  • Page 25 WARRANTY Dear Sir or Madam! Thank you for purchasing our product and congratulations on your right choice. The device that you bought was designed and manufactured according to the latest technologies and represents global standards of quality and reliability, while being environmentally friendly. We remind you to carefully read the commissioning and operation procedures before using the device;...

  • Page 26: Warranty Conditions

    WARRANTY CONDITIONS 1. NAX guarantees smooth operation of the device in accordance with the technical and operational conditions described in the User Manual. 2. The device is granted a 36-month warranty to the consumer (i.e. a natural person making a legal transaction with the entrepreneur not directly related to its business or professional activity) and a 12-month warranty when purchased by the entrepreneur (i.e.

  • Page 27: Warranty Card

    Warranty card ………………………………………………………………….. ……………………………………………………………………………………….. Equipment name * Model * …………………………… ………………………………………… ………………………………………… Date of sale * Device serial number * Engine serial number I declare that I have read the User Manual and the Warranty Card. I received the purchased equipment in working order, complete, along with the proof of purchase.

Table of Contents