Sears 917.255561 Owner's Manual page 8

ASSE
BLY
HOW TO SET UP YOUR TRACTOR
PREPARE BATTERY (See Fig. 2)
i llll i,. , i ,, i ,m i ,t=_,,,,
CAUTION: Wear eye and face shield,
Wash hands or clothing Immediately if
accldentallyln contact with battery actd.
Do not smoke. Fumes from charged
battery acld are explosive.
Read the Instructions Included with the
battery vent caps. Alwayswear gloves,
clothing and goggles to protect your
hands, skin and eyes.
Your tractor has a battery charging system which is suffi-
cient for normal use. However, periodic charging of the
battery with an automotive charger wili extend its life.
" See instructions packed with vent caps in parts bag.
, Fill battery with acid. Fill each cell until it reaches the
bottom of the vent we{Is. Do not overfill.
• Ailow battery to stand and settle for at least thirty
minutes. After standing, check the _evel of acid. If
below the vent wells, add more acid until the correct
level is reached.
While battery is standing (after adding acid) and later, while
battery isbeing charged, continue with assembly of tractor.
IMPORTANT: TO MAXiMiZE THE LIFE OF YOUR
BATTERY, IT IS NECESSARY THAT THE BATTERY BE
CHARGED BEFORE USE FAILURE TO CHARGE
BATTERY CAN RESULT {N A SHORTENED BATTERY
LiFE
• Charge battery at a rate of 6 amperes for 1 hour. Use
a 12 volt battery charger. Observe all safety precautions
required for battery charging.
. Check the acid level after the battery is charged, If the
acid has fallen below the correct level, add distilled or
iron free water.
. Install the vent caps to cover the vent weIIs. Wash the
top of the battery with water to remove any acid, then
wipe dry,
• Check battery case for leakage to make sure that no
damage has occurred in handling.
• Dispose of excess battery acid, Neutralize acid for
disposal by adding it to four inches of water in a five
gallon plastic container. Stir with a wooden or plastic
paddle white adding baking soda until the addition of
more soda causes no more foaming,
o Follow instructions on how to install battery.
CUTAWAYVIEW j VENTCAP
j w. W LL
_ BATTERY
t _ r-_ _ _ r_ _ r.,'J r_/f_t CELLAClD
INSTALL SEAT (See Fig. 3)
Adjust seat before tightening adjustment bolt.
° Remove cardboard packing on seat pan.
Place seat on pan and assemble shoulder bolt.
. Assemble adjustment bolt, lock washer and flat washer
loosely. Do not tighten.
• Tighten shoulder bolt securely.
, Lower seat into operating position and sit on seat.
. SIide seat until a comfortable position is reached which
aIIows you to press clutch/brake pedal all the way down
(See Fig. 6).
• Get off seat without moving its adjusted position.
, Raise seat and tighten adjustment bolt securely.
SEAT PAN
SHOULDER
BOLT
oFLAT WASHER
ADJUSTMENT " LOCK WASHER
BOLT
FIG, 3
CHECK TIRE PRESSURE
The tires on your tractor were overinflated at the factory for
shipping purposes. Correct tire pressure is important for
best cutting performance.
. Reduce tire pressure PSI shown in "PRODUCT
SPECIFICATION on page 3 of this manual.
CHECK DECK LEVELNESS
For best cutting results, mower housing should be properly
leveled. See "TO LEVEL MOWER HOUSING" in the
Service and Adjustments section of this manual.
CHECK FOR PROPER POSITION OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of this manual. Verify that the belts are routed
correctly.
CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see
that the brake is properly adjusted. See "TO ADJUST
BRAKE" in the Service and Adjustments section of this
manual
F1Go2 8