Black Stone BL 983319-0 Instruction Manual

Instruction Manual
BL 983319-0
BL 983319-1
Panel-Mounted
TDS Indicators &
Controllers
WARRANTY
These instruments are guaranteed for two years against defects in
workmanship and materials when used for their intended purpose and
maintained according to instructions. Electrodes and probes are guaranteed
for six months. This warranty is limited to repair or replacement free of
charge.
Damages due to accidents, misuse, tampering or lack of prescribed
maintenance are not covered.
If service is required, contact the dealer from whom you purchased the
instrument. If under warranty, report the model number, date of purchase,
serial number and the nature of the problem. If the repair is not covered
by the warranty, you will be notified of the charges incurred. If the
instrument is to be returned to Hanna Instruments, first obtain a Returned
Goods Authorization number from the Technical Service department and
then send it with shipping costs prepaid. When shipping any instrument,
make sure it is properly packaged for complete protection.
Recommendations for Users
Before using these products, make sure that they are entirely suitable for the environment
in which they are used. Operation of these instruments in residential areas could cause
unacceptable interferences to radio and TV equipment. Any variation introduced by the user
to the supplied equipment may degrade the instrument's EMC performance. To avoid
electrical shock, do not use these instruments when voltages at the measurement surface
exceed 24 Vac or 60 Vdc. To avoid damages or burns, do not perform any measurement in
microwave ovens.
Dear Customer,
Thank you for choosing a Hanna Instruments product.
Please read this instruction manual carefully before using
these instruments. This manual will provide you with the
necessary information for correct use of these instruments.
If you need additional technical information, do not hesitate
to e-mail us at tech@hannainst.com or view our worldwide
contact list at www.hannainst.com.
PRELIMINARY EXAMINATION
Remove the instrument from the packing material and
examine it carefully to make sure that no damage has
occurred during shipping. If there is any damage, notify
your Dealer or the nearest Hanna Customer Service Center.
Each meter is supplied with:
• Mounting brackets
• Instruction manual
Note: Save all packing material until you are sure that the
instrument functions correctly. All defective items must
be returned in the original packing with the supplied
accessories.
GENERAL DESCRIPTION
BL983319-0 and BL983319-1 are TDS indicators and
controllers with a relay output designed for simplicity of use in
a wide range of applications.
Connections and wiring to probe, power supply and contacts
are made via the terminal blocks on the rear panel.
The probe is easy to clean and requires little maintenance.
Other features include: automatic temperature compensation
of readings, single point calibration, overtime control system,
multi-colour LED for indicating if the meter is in measurement/
dosing/alarm condition, possibility to set (Off-Auto-On switch)
dosing action mode.
Two models are available:
• BL 983319-0 powered at 12 Vdc
• BL 983319-1 powered at 115 or 230 Vac
All rights are reserved. Reproduction in whole or in part is prohibited
without the written consent of the copyright owner, Hanna Instruments
Inc., Woonsocket, Rhode Island, 02895 , USA.
SPECIFICATIONS
Range 0 to 1999 ppm
Resolution 1 ppm
Accuracy ±2% f.s.
(@ 25 °C / 77 °F)
TDS conversion factor 0.65
Probe HI 7634-00 EC/TDS probe (not included)
Temp.Compensation Automatic from 5 to 50 °C (41 to 122 °F);
ß=2%/ºC
Calibration Manual, through CAL trimmer
Dosing Contact Maximum 2A (fuse protected), 250 Vac, 30 Vdc
Contact close when measure < setpoint
Setpoint Adjustable, from 0 to 1999 ppm
Overtime Adjustable, typically from 5 to approx. 30 minutes
Power Consumption 10 VA
Installation Category II
Power supply: External (fuse protected)
BL983319-0
12 Vdc
BL983319-1 115/230 Vac ; 50/60 Hz
Dimensions 79 x 49 x 95 mm (3.1 x 1.9 x 3.7")
ASSEMBLING VIEW
ACCESSORIES
HI 7634-00
EC/TDS probe
HI 70031P 1413 µS/cm calibration solution, 20 mL
sachet (25 pcs.)
HI 7031M 1413 µS/cm calibration solution, 230 mL
HI 7031L 1413 µS/cm calibration solution, 500 mL
HI 7061M Probe cleaning solution, 230 mL bottle
HI 7061L Probe cleaning solution, 500 mL bottle
HI 710005 12 Vdc power adapter, US plug
HI 710006 12 Vdc power adapter, European plug
HI 710012 12 Vdc power adapter, Australian plug
HI 710013 12 Vdc power adapter, South African plug
HI 710014 12 Vdc power adapter, UK plug
HI 731326 Calibration screwdriver (20 pcs.)
HI 740146 Mounting brackets