Table of Contents
Advertisement
is wired correctly. Before attempting to reverse the throttle channel
using the procedure below, you should first recalibrate the speed
control. Refer to "XL-5 Setup Programming" on page 21.
1. Press and hold the SET button on the transmitter for two
seconds. The status LED will flash green.
2. Move and hold the throttle trigger to the full forward or full
brake position (it does not matter which position you choose).
3. While holding the throttle trigger in position, press the SET
button to reverse the channel.
4. The channel is now reversed. Recalibrate the speed control and
then confirm correct servo operation before running
your model.
USING THE RADIO SYSTEM
The TQ 2.4GHz Radio System has been adjusted at the factory for
correct operation with your model. The adjustment should be
checked before running the model, in case of movement during
shipping. Here's how:
1. Turn the transmitter switch on. The status LED on the
transmitter should be solid green (not flashing).
2. Elevate the model so that the rear tires are off the ground.
If you are holding the model, grip it firmly. Make sure your
hands are clear of the moving parts of the model.
3. Plug the battery pack in the model into the speed control.
4. Press and release the EZ-Set button on the speed control to
turn the model on. The speed control's LED will glow red. To
turn the speed control off, press the EZ-Set button until the LED
turns off.
Note: If the LED shines green after the speed control is turned
on, Low-Voltage Detection is activated. This may cause poor
performance from NiMH battery packs. Make sure to turn the
Low-Voltage Detection on when using LiPo batteries. Never use
LiPo batteries while Low-Voltage Detection is turned off. See
page 21 for more information.
5. Turn the steering wheel on the transmitter back and forth and
check for rapid operation of the steering servo. Also, check that
the steering mechanism is not loose or binding. If the steering
operates slowly, check for weak batteries.
TRAXXAS TQ 2.4GHz RADIO SYSTEM
6. When looking down at the
0°
model, the front wheels
should be pointing straight
ahead. If the wheels are
turned slightly to the left
or right, slowly adjust the
steering trim control on the transmitter until they are pointing
straight ahead.
°
°
7. Operate the throttle trigger to ensure that you have full forward
1
-2
and reverse operation, and that the motor stops when the
throttle trigger is at neutral.
8. Once adjustments are made, turn off your model, followed by
the hand-held transmitter.
Range-Testing the Radio System
Before each running session with your model, you should range-
test your radio system to ensure that it operates properly.
1. Turn on the radio system and check its operation as described in
the previous section.
2. Have a friend hold the model. Make sure hands and clothing are
clear of the wheels and other moving parts on the model.
3. Walk away from the model with the transmitter until you reach
the farthest distance you plan to operate the model.
4. Operate the controls on the transmitter once again to be sure
that the model responds correctly.
5. Do not attempt to operate the model if there is any problem
with the radio system or any external interference with your
radio signal at your location.
Higher Speeds Require Greater Distance
The faster you drive your model, the more quickly it will near the
limit of radio range. At top speeds, models can cover anywhere
between 50 to 100 feet every second! It's a thrill, but use caution to
keep your model in range. If you want to see your model achieve
its maximum speed, it is best to position yourself in the middle
of the truck's running area, not the far end, so you drive the truck
towards and past your position. In addition to maximizing the
radio's range, this technique will keep your model closer to you,
making it easier to see and control.
Your model's radio system is designed to operate reliably up to
the approximate distance that it is no longer easy or comfortable
0°
Using Reverse: While driving,
push the throttle trigger
forward to apply brakes.
Once stopped, return the
throttle trigger to neutral.
Push the throttle trigger
forward again to engage
proportional reverse.
°
°
1
-2
7,8
7,8
TRAXXAS • 19
Advertisement
Table of Contents
