Table of Contents
Advertisement
RYOBI WARRANTY APPLICATION ONDITIONS
In addition to any statutory rights resulting from the purchase, this product is covered
by a warranty as stated below.
1.
The warranty period is 24 months for consumers and commences on the date
the product was purchased. This date has to be documented by an invoice or
other proof of purchase. The product is designed and dedicated to consumer
and private use only. So there is no warranty provided in case of professional or
commercial use. This warranty applies only on new products.
2.
There is a possibility to extend for a part of the range of power tools (AC/DC)
the warranty period over the period described above using the registration on
the www.ryobitools.eu website. The eligibility of products for extended warranty
is clearly displayed in stores and / or on packaging and is contained within the
product documentation. The end user is required to register his/her newly-
acquired products online within 30 days from the date of purchase. The end user
may register for the extended warranty in his/her country of residence if listed on
the online registration form where this option is valid. Furthermore, end users
must give their consent to the storage of their personal data that is required to be
entered online. They must also accept the terms and conditions. The registration
confirmation receipt, which is sent out by e-mail, and the original invoice showing
the date of purchase will serve as proof of the extended warranty.
3.
The warranty covers all defects of the product during the warranty period due to
faults in workmanship or material at the purchase date. The warranty is limited to
repair and/or replacement and does not include any other obligations including
but not limited to incidental or consequential damages. The warranty is not valid
if the product has been misused, used contrary to the instruction manual, or has
been incorrectly connected to a power supply. This warranty does not apply to:
–
any damage to the product that is the result of improper or lack of
maintenance
–
any product that has been altered or modified
–
any product where original identification (trade mark, serial number)
markings have been defaced, altered or removed
–
any damage caused by non-observance of the instruction manual
–
any product not displaying the CE approval mark on the rating plate
–
any product that has been attempted to be repaired by a non-authorised
warranty service centre or without prior authorisation by Techtronic
Industries
–
any product connected to an improper power supply (amps, voltage,
frequency)
–
any product used with inappropriate fuel mixture (fuel, oil, Ratio of oil / fuel
mixture)
–
any damage caused by external influences (water, chemical, physical,
shocks) or foreign substances
–
normal wear and tear spare parts
–
inappropriate use, overloading of the tool
–
use of non-approved accessories or parts
–
Accessories provided with the tool or purchased separately including but
not limited to blades, saw chains, cutting lines etc.
–
Any periodic adjustments to or maintenance cleaning of carburetors
–
Components (parts and accessories) subject to natural wear and tear,
including but not limited to bump knobs, drive belts, clutch, blades of hedge
trimmers or lawn mowers, harness, cable throttle, carbon brushes, power
cord, tines, felt washers, hitch pins, blower fans, blower and vacuum tubes,
vacuum bag and straps, guide bars, saw chains, hoses, connector fittings,
spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines,
spark plugs, air filters, gas filters, mulching blades, etc.
4.
For servicing, the product must be sent or presented to a RYOBI authorised
service station listed for each country in the following list of service station
addresses. In some countries your local RYOBI dealer undertakes to send the
product to the RYOBI service organisation. When sending a product to a RYOBI
service station, the product should be safely packed without any dangerous
contents such as petrol, marked with sender's address and accompanied by a
short description of the fault.
5.
A repair / replacement under this warranty is free of charge. It does not constitute
an extension or a new start of the warranty period. Exchanged parts or products
become our property. In some countries delivery charges or postage will have
to be paid by the sender. Your statutory rights arising from the purchase of the
product remain unaffected.
6.
This warranty is valid in the European Community, Switzerland, Iceland, Norway,
Liechtenstein, Turkey, Russia, and the United Kingdom. Outside these areas,
please contact your authorised RYOBI dealer to determine if another warranty
applies.
AUTHORISED SERVICE CENTRE
Any request or issue with the product can be addressed to your local authorised
service centres (visit www.ryobitools.eu) or directly to: Techtronic Industries GmbH,
Max Eyth Straße 10, 71364 Winnenden, Germany. Please state the serial number and
product type printed on the label.
EC DECLARATION OF CONFORMITY
Manufacturer: Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
We declare as the manufacturer under our sole responsibility that the product
mentioned below
Cordless power washer
Brand: RYOBI
Model number: RY18PWX41A
Serial number range: 47590201000001 - 47590201999999
fulfills all the relevant provisions of the following European Directives, European
Regulations and harmonized standards:
2006/42/EC, 2014/30/EU, 2011/65/EU, EN 55014-1:2017+A11,
EN 55014-2:2015, EN 60335-1:2012+A1+A2+A11+A13+A14,
EN 60335-2-79:2012, EN 62233:2008, EN IEC 63000:2018
Sven Eschrich
VP of Engineering - TTI Outdoor Power Division
Winnenden,
Feb. 2, 2021
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
GB-DECLARATION OF CONFORMITY
Manufacturer: Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
We declare as the manufacturer under our sole responsibility that the product
mentioned below
Cordless power washer
Brand: RYOBI
Model number: RY18PWX41A
Serial number range: 47590201000001 - 47590201999999
fulfills all the relevant provisions of the following Regulations: S.I. 2008/1597 (as
amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended), and that the
following designated standards have been used:
BS EN 55014-1:2017+ A11, BS EN 55014-2:2015,
BS EN 60335-1:2012+A1+A2+A11+A13+A14,
BS EN 60335-2-79:2012, BS EN 62233:2008,
BS EN IEC 63000:2018
Sven Eschrich
VP of Engineering - TTI Outdoor Power Division
Winnenden,
Feb. 2, 2021
Authorised to compile the technical file:
Techtronic Industries (UK) Ltd
Fieldhouse Lane
Marlow Bucks SL7 1HZ
UK
RYOBI is a trade mark of Ryobi Limited,
and is used under license.
Advertisement
Table of Contents
