Advertisement
BEFORE STARTING THE ENGINE
CHECK
ENGINE
OIL LEVEL
i The engine in your tractor has been
shipped, from the factory, already filled
with summer weight oil.
Check engine oil with tractor on level
ground.
• Remove oil fill cap/dipstick and wipe
clean, reinsert the dipstick and screw
cap tight, wait for a few seconds,
remove and read oil level. If necessary,
add oil until =FULL" mark on dipstick is
reached.
Do not overfill.
• For cold weather operation you should
change oil for easier starting (See =OIL
VISCOSITY
CHART" in the Mainte-
nance section
of this manual).
• To change
engine oil, see the Mainte-
nance section
in this manual.
ADD
GASOLINE
• Fill fuel tank. Use fresh, clean, regular
unleaded
gasoline with a minimum of 87
octane. (Use of leaded gasoline will
increase carbon and lead oxide
deposits and reduce valve life). Do not
mix oil with gasoline. Purchase fuel in
quantities that can be used within 30
days to assure fuel freshness.
IMPORTANT:
When operating in tempera-
tures below 32°F(0°C),
use fresh, clean
winter grade gasoline to help insure good
_Nweather
starting.
ARNING:
Experience
indicates that
alcohol blended fuels (called gasohol or
using ethanol or methanol) can attract
moisture which leads to separation and
formation of acids during storage. Acidic
gas can damage the fuel system of an
engine while in storage. To avoid engine
problems, the fuel system should be emp-
tied before
storage of 30 days or longer.
Drain the gas tank, start the engine and let
it run until the fuel lines and carburetor are
empty. Use fresh fuel next season. See
Storage
Instructions for additional informa-
tion. Never use engine or carburetor
cleaner products in the fuel tank or perma-
znt
damage may occur.
CAUTION:
Fill to bottom of gas tank
filler neck. Do not overfill. Wipe off any
spilled oil or fuel. Do not store, spill or use
gasoline near an open flame.
TO START ENGINE
When starting
the engine for the first time
or if the engine has run out of fuel, it will
take extra cranking
time to move fuel from
the tank to the engine.
16
• Be sure freewheel control is in the
transmission engaged position.
• Sit on seat in operating p6sition,
depress clutch/brake pedal and set
parking brake.
• Place motion control lever in neutral (N)
position.
• Move attachment clutch to =DISEN-
GAGED" position.
• Move throttle control to fast position
• Pull choke control out for a cold engine
start attempt. For a warm engine start
attempt the choke control may not be
needed.
NOTE:
Before starting, read the warm and
cold starting
procedures below.
• Insert key into ignition and turn key
clockwise to =START" position and
release key as soon as engine starts.
Do not run starter Continuously for more
than fifteen seconds per minute. If the
engine does not start after several
attempts, push choke control in, wait a
few minutes and try again. If engine still
does not start, pull the choke control out
and retry.
WARM WEATHER
STARTING
(50 ° F
AND ABOVE)
• When engine starts, slowly push choke
control in until the engine begins to run
smoothly. If the engine starts to run
roughly, pull the choke control out slight-
ly for a few seconds and then continue
to push the control in slowly.
• The attachments
and ground drive can
now be used. If the engine does not
accept the load, restart the engine and
allow it to warm up for one minute using
the choke as described above.
COLD WEATHER
STARTING
(50 ° F AND
BELOW)
• When engine starts, slowly push choke
control in until the engine begins to run
smoothly. Continue to push the choke
control in small steps allowing the
engine to accept small changes in
speed and load, until the choke control
is fully in, If the engine starts to run
roughly, pull the choke control out slight-
ly for a few seconds and then continue
to push the control in slowly. This may
require an engine warm-up period from
several seconds to several minutes,
depending on the temperature.
Advertisement
