Advertisement
Quick Links
Service Manual
Washing Machine
Model: DW-K500C / DW-K501C
Caution
: In this Manual, some parts can be changed for improving,
their performance without notice in the parts list. So, if you
need the latest parts information, please refer to PPL(Parts
Price List) in Service Information Center (http://svc.dwe.co.kr).
DAEWOO ELECTRONICS CORP.
http : //svc.dwe.co.kr
S/M No. : DWK500C001
Nov. 2005
Advertisement
Related Manuals for Daewoo DW-K500C
Summary of Contents for Daewoo DW-K500C
- Page 1 S/M No. : DWK500C001 Service Manual Washing Machine Model: DW-K500C / DW-K501C Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service Information Center (http://svc.dwe.co.kr).
- Page 2 SHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASH TO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER SHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASH TO WASHER AUTO WASHER AUTO WASHER...
-
Page 3: Specification
ITEM SPECIFICATION POWER VOLTAGE AC 110V AC 220V SOURCE FREQUENCY 60Hz 50Hz POWER PUMP 415W CONSUMPTION NON PUMP NET : 690 X 400 X 830 (mm, WXDXH) DIMENSION MACHINE PUMP NET: 18.5kg WEIGHT NON PUMP STRONG, NORMAL WASHING COURSE LOW (25ℓ), MID (32ℓ), HIGH (40ℓ) WATER LEVEL TIMER WASH... - Page 5 Causes and settlements Troubles Causes Settlement Washing is forceless,pulsator 1. Belt loosen 1. Tighten or Replace the belt work slowly 2. Too much washer 2. Decrease the washer 3. Low voltage 3. Wash after the refresh of voltage Pulsator, spin tub can’t work 1.No power(power cut or fuse break 1.Check the power and no sound from the motor...
- Page 6 lubricating The pulsator can’t rotated in 1.Wash timer damaged 1.Replace the wash timer negative or positive 2.Selector damaged 2.Replace the selector Not well drain or no drain 1.Some foreign matters clog the drain valve 1.Clean the foreign matters 2.The drain valve open height not reach the 2.Adjust the drain valve right height right position 3.Lower down the drain pipe...
- Page 7 Repair main points and notes Adjust the tightness degree of belt 1. Cut off the power 2. Open the machine rear cover 3. Loose the screws fixed on the wash motor 4. Move the motor to the correct position 5. Re-install according to the opposite course Replace the belt 1.
- Page 8 Replace the capacitor 1. Cut off the power 2. Open the machine rear cover 3. Unclamp the connction wire 4. Take out the capacitor (or open the capacitor fixer) 5. Re-install the capacitor in opposite course Replace reducer 1. Cut off the power 2.
- Page 9 3. If can’t take out the foreign matters under the above condition, please open the machine rear cover 4. Screw off the spin tub screws, take out the spin tub 5. Clean the foreign matters on the shaft 6. Re-install the spin tub in opposite course Replace the rubber cap 1.
- Page 10 TOP PLATE ASS'Y / SPIN TUB / PULSATOR...
- Page 11 BODY / BASE...
-
Page 12: Parts List
PARTS LIST...