Table of Contents
Advertisement
en
ENGLISH
Tighten the saw blade fixing screw (23) using the
(17) hexagon wrench.
Use only sharp, undamaged saw blades. Do
not use saw blades that are cracked or that
have changed their shape.
Do not use any saw blades which have a
thicker base body or a smaller width cut than
the riving knife.
Do not use any saw blades made from high-
alloy high-speed steel (HSS).
Do not use any saw blades which do not
conform to the specified rating.
Use only saw blades with a diameter according to
the markings on the saw.
The saw blade must be suitable for the no-load
speed.
Use a saw blade that is suitable for the
material being sawn.
Use only genuine Metabo - saw blades. Saw
blades intended for cutting wood or similar
materials have to conform to EN 847-1.
9. Cleaning
Dust deposits must be regularly removed from the
machine. This includes vacuum cleaning the
ventilation louvres on the motor. Make sure that the
safety appliances, (e.g. the movable guard,
movable riving knife) are in perfect working order.
The movable guard and the riving knife must move
freely, automatically, easily and exactly back into its
end position.
10. Troubleshooting
Switching on the machine briefly reduces the
voltage. Unfavourable mains power conditions may
have a detrimental effect on other machines. Power
impedances less than 0.3 ohm should not cause
malfunctions.
11. Accessories
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
For the complete range of accessories, see
www.metabo.com or the main catalogue.
12. Repairs
Repairs to electrical tools must only be carried
out by qualified electricians!
A defective mains cable must be replaced only with
a special, original mains cable from Metabo
available from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
14
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
14. Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
P
= Rated input
1
P
= Power output
2
n
= No-load speed
0
n
= On-load speed
1
T
= maximum depth of cut
max
T
= max. depth of cut (90°)
90°
T
= max. depth of cut (45°)
45°
A
= adjustable angular cut angle
Ø
= saw blade diameter
d
= saw blade drill diameter
a
= max. base body thickness of the saw
blade
b
= cutting width of the saw blade
c=
= thickness of riving knife
m
= weight
Measured values determined in conformity with EN
62841.
Machine in protection class II
~
AC Power
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a
= Vibration emission value
h, D
(Sawing chip board)
K
= Uncertainty (vibration)
h,D
Advertisement
Table of Contents
