Sony CDX-CA890X Installation/Connections

FM/AM
Compact Disc
Player
Installation/Connections
Instalación/Conexiones
安裝 線路連接
CDX-CA890X
Sony Corporation © 2003
1
1 2
4 5
× 4
Equipment used in illustrations (not supplied)
Equipo utilizado en las ilustraciones (no suministrado)
插圖中的裝置（非附送）
Front speaker
Altavoces delanteros
前揚聲器
Rear speaker
Altavoces traseros
後揚聲器
Power amplifier
Amplificador de potencia
功率放大器
3-247-570-21 (1)
Printed in Thailand
3
6 7
× 2
CD/MD changer
Cambiador de CD/MD
CD/MD 換碟機
Rotary commander RM-X4S
Mando rotativo RM-X4S
旋轉式控制器 RM-X4S
Active subwoofer
Subwoofer activo
有源超低音揚聲器
2
A
SUB OUT (MONO)
AUDIO OUT
B
Source selector*
Selector de fuente*
音源選擇器*
XA-C30
Cautions
• This unit is designed for negative earth 12 V DC
operation only.
• Do not get the wires under a screw, or caught in
moving parts (e.g. seat railing).
• Before making connections, turn the car ignition off to
avoid short circuits.
• Connect the yellow and red power input leads only
after all other leads have been connected.
• Run all earth wires to a common earth point.
• Be sure to insulate any loose unconnected wires with
electrical tape for safety.
Notes on the power supply cord (yellow)
• When connecting this unit in combination with other
stereo components, the connected car circuit's rating
must be higher than the sum of each component's fuse.
• When no car circuits are rated high enough, connect the
unit directly to the battery.
Parts Iist (1)
• The numbers in the list are keyed to those in the
instructions.
• The bracket 1 and the protection collar 5 are attached
to the unit before shipping. Before mounting the unit,
use the release keys 6 to remove the bracket 1 and the
protection collar 5 from the unit. For details, see
"Removing the protection collar and the bracket (4)"
on the reverse side of the sheet.
• Keep the release keys 6 for future use as they are
also necessary if you remove the unit from your car.
Caution
Handle the bracket 1 carefully to avoid injuring your
fingers.
1 Catch
Note
Before installing, make sure that the catches on both sides of
the bracket 1 are bent inwards 2 mm. If the catches are
straight or bent outwards, the unit will not be installed
securely and may spring out.
Connection example (2)
Notes (2-A)
• Be sure to connect the earth cord before connecting the
amplifier.
• If you connect an optional power amplifier and do not use
the built-in amplifier, the beep sound will be deactivated.
Tip (2-B- )
For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.
AUDIO OUT
FRONT
REAR
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
BUS CONTROL IN
* not supplied
Connection diagram (3)
1
To a metal surface of the car
First connect the black earth lead, then connect the
yellow and red power input leads.
2 To the power aerial control lead or power supply
lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there is no
power aerial or aerial booster, or with a manually-
operated telescopic aerial.
• When your car has a built-in FM/AM aerial in the rear/
side glass, see "Notes on the control and power
supply leads."
3
To AMP REMOTE IN of an optional power amplifier
This connection is only for amplifiers. Connecting any
other system may damage the unit.
4 To the interface cable of a car telephone
5 To the +12 V power terminal which is energised in
the accessory position of the ignition key switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energised at all
times.
Be sure to connect the black earth lead to a metal
surface of the car first.
• When your car has a built-in FM/AM aerial in the rear/
side glass, see "Notes on the control and power
supply leads."
6
To the +12 V power terminal which is energised at
all times
Be sure to connect the black earth lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +cc 12 V
when you turn on the tuner.
• When your car has built-in FM/AM aerial in the rear/side
glass, connect the power aerial control lead (blue) or the
accessory power input lead (red) to the power terminal of
the existing aerial booster. For details, consult your
dealer.
• A power aerial without relay box cannot be used with
this unit.
Memory hold connection
When the yellow power input lead is connected, power will
always be supplied to the memory circuit even when the
ignition key is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms , and
with adequate power handling capacities to avoid its
damage.
• Do not connect the speaker terminals to the car chassis,
or connect the terminals of the right speakers with those
of the left speaker.
• Do not connect the earth lead of this unit to the negative
(–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active
speakers (with built-in amplifiers) to the speaker
terminals may damage the unit.
• To avoid a malfunction, do not use the built-in speaker
wires installed in your car if the unit shares a common
negative (–) lead for the right and left speakers.
• Do not connect the unit's speaker cords to each other.
Note on connection
If speaker and amplifier are not connected correctly,
"FAILURE" appears in the display. In this case, make sure
the speaker and amplifier are connected correctly.
no suministrado
非附送