Summary of Contents for NAMICAM DC2000A
- Page 1 DC2000A DC3000A CYCLONE DUST COLLECTORS 2.5HP 1.75HP Operator's Manual Record the serial number and date of purchase in your manual for future reference. The serial number can be found on the specification label on the side of your machine.
-
Page 2: Safety Instructions
SAFETY INSTRUCTIONS IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. There are certain applications for which this tool was designed. - Page 3 SAFETY INSTRUCTIONS 12. KEEP PROTECTIVE GUARDS IN PLACE AND IN 25. ALWAYS WEAR A DUST MASK TO PREVENT WORKING ORDER. INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust 13. AVOID ACCIDENTAL STARTING. Make sure that and asbestos dust. Direct particles away from face and the power switch is in the “OFF”...
- Page 4 SAFETY INSTRUCTIONS - DC2000A EXTENSION CORDS ELECTRICAL SAFETY THE USE OF AN EXTENSION CORD THIS TOOL MUST BE GROUNDED WITH THIS MACHINE IS NOT RECOMMENDED. For WHILE IN USE TO PROTECT THE OPERATOR FROM best power and safety, plug the machine directly into a ELECTRIC SHOCK.
- Page 5 SAFETY INSTRUCTIONS - DC3000A ELECTRICAL SAFETY EXTENSION CORDS THIS TOOL REQUIRES THE USE OF USE OF AN EXTENSION CORD A 230V PLUG (NOT INCLUDED), AND MUST BE WITH THIS MACHINE IS NOT RECOMMENDED. FOR GROUNDED WHILE IN USE TO PROTECT THE BEST POWER AND SAFETY, PLUG THE MACHINE OPERATOR FROM ELECTRIC SHOCK.
- Page 6 SAFETY INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR DUST COLLECTORS This machine is intended for the collection of chips, shavings and dust from the surfacing, cutting and sanding of natural wood, plywood, plastics and other man-made wood based composites. It is for collecting DRY materials only.
-
Page 7: Dust Hazards And Safety
DUST HAZARDS AND SAFETY EMPTYING & CLEANING THE DUST COLLECTOR CAUTION: Make sure the dust collector is unplugged before cleaning or servicing. Always wear a dust mask or respirator while emptying the collector bags or cleaning the dust collector. Please refer to the California Proposition 65 warning on page 7 of this manual regarding hazards from exposure to wood dust. -
Page 8: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION 1. Plug cord into electrical outlet. 1. Machine not plugged in. 2. Lift switch to ‘ON’ position. The safety 2. Power switch in ‘OFF’ position. key must be in place. See page 11. 3. Power switch or cord is faulty. Motor does not 3. -
Page 9: Maintenance
MAINTENANCE Turn the power switch “OFF” and disconnect the plug from the outlet prior to adjusting or maintaining the machine. DO NOT attempt to repair or maintain the electrical components of the motor. Contact a qualified service technician for this type of maintenance. 1. - Page 10 DC2000A PARTS DIAGRAM A NOTE: Please reference the Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required.
- Page 11 DC2000A PARTS LIST A PART DESCRIPTION QTY. Dust Plenum P60-1750-1A Cyclonic Separator P60-1750-2A Hex lock nut M6 P60-1750-3A Hex socket flat round hd screw M6X16 P60-1750-4A Inlet P60-1750-5A Muti-Way Connector cover P60-1750-6A Collection Drum Cover P60-1750-7A Steel ring P60-1750-8A Cross recessed pan head screw M5X8...
- Page 12 DC2000A PARTS DIAGRAM B NOTE: Please reference the Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required.
- Page 13 DC2000A PARTS LIST B PART DESCRIPTION QTY. Cap nut M10 P60-1750-1B Motor P60-1750-2B Hex head flange bolt M8X16 P60-1750-3B Motor mounting plate P60-1750-4B Flat washer 10 P60-1750-5B Spring washer 10 P60-1750-6B Hex headed bolt M10X30 P60-1750-7B Impeller P60-1750-8B Big washer 8...
- Page 14 DC2000A PARTS DIAGRAM C NOTE: Please reference the Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required.
- Page 15 DC2000A PARTS LIST C PART DESCRIPTION QTY. Filter cartridge P60-1750-1C Filter cartridge shield P60-1750-2C Hex head flange bolt M8X16 P60-1750-3C Hex lock nut M6 P60-1750-4C Spring clip P60-1750-5C Hex socket flat round hd screw M6X12 P60-1750-6C Handle P60-1750-7C Clamping assembly...
- Page 16 DC2000A PARTS DIAGRAM D NOTE: Please reference the Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required. DC2000A PARTS LIST D PART DESCRIPTION QTY. Base bracket P60-1750-1D Hex socket flat round hd screw M6X16...
- Page 17 DC2000A NOTES Use this section to record maintenance, service and any calls to Technical Support:...
- Page 18 DC3000A PARTS DIAGRAM A NOTE: Please reference the Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required.
- Page 19 DC3000A PARTS LIST A PART DESCRIPTION QTY. Dust Plenum P60-2500-1A Cyclonic Separator P60-2500-2A Hex lock nut M6 P60-2500-3A Hex socket flat round hd screw M6X16 P60-2500-4A Inlet P60-2500-5A Muti-Way Connector cover P60-2500-6A Collection Drum Cover P60-2500-7A Steel ring P60-2500-8A Cross recessed pan head screw M5X8 P60-2500-9A Vertical column P60-2500-10A...
- Page 20 DC3000A PARTS DIAGRAM B NOTE: Please reference the Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required.
- Page 21 DC3000A PARTS LIST B PART DESCRIPTION QTY. Cap nut M10 P60-2500-1B Spring washer 10 P60-2500-2B Flat washer 10 P60-2500-3B Motor P60-2500-4B Hex head flange bolt M8X16 P60-2500-5B Motor mounting plate P60-2500-6B Hex headed bolt M10X30 P60-2500-7B Impeller P60-2500-8B Big washer 8 P60-2500-9B Spring washer 8 P60-2500-10B...
- Page 22 DC3000A PARTS DIAGRAM C NOTE: Please reference the Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required.
- Page 23 DC3000A PARTS LIST C PART DESCRIPTION QTY. Filter cartridge P60-2500-1C Filter cartridge shield P60-2500-2C Hex head flange bolt M8X16 P60-2500-3C Hex lock nut M6 P60-2500-4C Spring clip P60-2500-5C Hex socket flat round hd screw M6X12 P60-2500-6C Handle P60-2500-7C Clamping assembly P60-2500-8C Hex socket flat end set screw M6X10 P60-2500-9C...
- Page 24 DC3000A PARTS DIAGRAM D NOTE: Please reference the Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required. DC3000A PARTS LIST D PART DESCRIPTION QTY. Base bracket P60-2500-1D Hex socket flat round hd screw M6X16 P60-2500-2D Caster wheel P60-2500-3D...
- Page 25 DC3000A NOTES Use this section to record maintenance, service and any calls to Technical Support:...