Page 1
Owner’s Manual and Installation Guide RUB1.1000D RUB1.1600D RUB1.2500D...
Page 2
Please retain this manual and you sales receipt for future reference. Soundstream amplifiers are the result of American innovation and the highest quality control standards. When properly installed, they will provide you with many years of listening pleasure.
Page 3
FEATURES Total Harmonic Distortion:0.5% Frequency Response: 15-150Hz Signal to Noise Ratio: 105dB Damping Factor: >250 Input Sensitivity 100mV - 8V 50-150Hz,12dB Low Pass Fiter 45Hz, 0-18dB Bass Boost 10-40Hz, 12dB Subsonic Filter 180° Phase Switch Midnight Blue Finish w/ Brushed Accents Remote Gain Control Master/Slave Operation Pre-amp Outputs...
TOOLS/PARTS FOR INSTALLATION NOTE: TOOLS ARE NOT SUPPLIED Small flat blade screwdriver phillips screwdriver (#2 or medium sized), Wire cutters, Wire strippers, - #6 round head screws, and 1 - #8 sheet metal screw (or nut, bolt flat washer, start washer) (see detail) 2 Ring connectors (large enough to accommodate your method of grounding) In-line fuse or Grommets (Sized to work with the power wire you plan to use in your installation) Tube of silicone seal.
Page 6
Electrical Wiring All RUBICON Amplifiers are equipped with easy top access screw terminals . These terminals are nickel-plated in order to ensure excellent electrical contact and to resist corrosion. When making electrical connections to the amplifier, please observe the following : Use at least 4 gauge or heavier wire for power and ground connections.
PANEL LAYOUT RUB1.1000D LEFT VIEW RIGHT VIEW RUB1.1600D LEFT VIEW RIGHT VIEW Subsonic Low Pass Input Line Out Line Input Level Filter Filter 10Hz 40Hz 50Hz Bridged Input Sensitivity Mode .1V-2V 2V-8V SPEAKER FUSES Subsonic Low Pass Input Line Out Line Input Level Filter...
PANEL LAYOUT RUB1.2500D LEFT VIEW RIGHT VIEW Class D Monoblock Amplifier Installation Wiring RUB1.1000D/RUB1.1600D/RUB1.2500D Low Level Inputs Line Out Line Input Input Subsonic Low Pass Bass Line Out Filter Filter Boost Level 10Hz 40Hz 50Hz 150Hz +18dB Input Sensitivity Bridged Mode DATALINK .1V-2V...
Page 9
Class D Monoblock Amplifier Installation Wiring RUB1.1000D/RUB1.1600D FUSES SPEAKER RUB1.1600D has four fuses here SPEAKER FUSES RUB1.1600D has four fuses here BATT+ REMOTE POWER CONNECTIONS BATT+ REMOTE POWER CONNECTIONS...
Page 10
Class D Monoblock Amplifier Installation Wiring RUB1.2500D SPEAKER POWER CONNECTIONS SPEAKER POWER CONNECTIONS...
Page 11
Bridging Two RUB1.1000D/RUB1.1600D/RUB1.2500D Amplifiers Line Out Line Out Input Subsonic Low Pass Line Input Filter Filter Level 10Hz 40Hz 50Hz 150Hz Bridged Input Sensitivity Mode .1V-2V 2V-8V Master Subsonic Low Pass Input Line Input Filter Filter Level 10Hz 40Hz 50Hz 150Hz Bridged Input Sensitivity...
Page 12
Bridging Two RUB1.1000D/RUB1.1600D Amplifiers SPEAKER SPEAKER BATT+ REMOTE POWER CONNECTIONS FUSES RUB1.1600D has four fuses here BATT+ REMOTE POWER CONNECTIONS FUSES...
Page 13
Bridging Two RUB1.2500D Amplifiers SPEAKER POWER CONNECTIONS SPEAKER POWER CONNECTIONS...
TROUBLE SHOOTING NO SOUND Is the LED lit? See your Authorize Sound Stream Dealer. SOUND IN ONE CHANNEL ONLY Reverse left and right speakers by unplugging the speaker connector. turning it over and plugging it back in. OPPOSITE CHANNEL Reverse RCA inputs OPPOSITE CHANNEL Reverse RCAs at head unit OPPOSITE CHANNEL...
Page 15
Caution: Please do not plug in or unplug RCA Plugs to the amplifier inputs while the amplifier is turned on. Doing so is potentially harmful to the amplifier by allowing RF(radio frequencies) into the amplifier, causing instability, during the brief period while the RCA shield is not connected, and the hot is connected.