Bosch 2 Series Quick Reference Manual page 2

Cleaning filters
After each wash check the filters for
1.
residue.
Turn the coarse
2.
2
filter anticlock-
wise and re-
move the filter
system ⁠ .
1
Pull down the mi-
3.
cro filter to re-
move.
Troubleshooting
Fault Cause and troubleshooting
Display for water supply Supply hose is kinked.
lights up
Install the supply hose without kinks.
▶
Water tap is turned off.
Turn on the water tap.
▶
Water tap is jammed or furred up.
Turn on the water tap.
▶
The filters in the water connection of the supply or AquaStop
hose are blocked.
Switch off the appliance.
1.
2. Pull out the mains plug.
3. Turn off the water tap.
4. Unscrew the water connection.
5. Remove the filter from the sup-
ply hose
6. Clean the filter.
7. Re-insert the filter in the supply hose.
8. Screw the water connection back on.
9. Check the water connection for leaks.
Restore the power supply.
10.
Switch the appliance on.
11.
Press the locking
4.
2
catches to-
gether and lift
1
the coarse filter
out ⁠ .
Clean the filter elements under running
5.
water.
Re-assemble the filter system.
6.
Insert the filter system into the appliance
7.
and turn the coarse filter clockwise.
Make sure that the arrow markings
match up.
Fault
Display for water supply
lights up
Remnants of food on
tableware.
Cleaning spray arms
Unscrew the upper spray arm and
1.
pull down to remove ⁠ .
Pull up the lower spray arm to remove.
2.
Check the outlet nozzles on the spray arms for blockages un-
3.
der running water and remove any foreign bodies.
Insert the lower spray arm.
4.
a The spray arm clicks into position.
5. Insert the upper spray arm and screw it firmly in place.
Cause and troubleshooting
Wastewater hose is blocked or kinked.
1. Reposition the wastewater hose without kinks.
Remove residues.
2.
Siphon connection is still sealed.
Check the connection to the siphon and open if necessary.
▶
Cover of the wastewater pump is loose.
Secure the cover of the Wastewater pump so it clicks into
▶
position.
Tableware is placed too close together or basket is overfilled.
Arrange tableware with sufficient space in between.
1.
The spray jets must reach the surfaces of the tableware.
Avoid points of contact.
2.
Spray arm rotation is blocked.
Arrange tableware so that it does not obstruct spray arm ro-
▶
tation.
Spray arm nozzles are blocked.
Clean the Spray arms.
▶
Filters are soiled.
Clean the filters.
▶
Filters are inserted incorrectly and/or not engaged.
Insert the filters properly.
1.
2. Engage the filters.
Clean wastewater pump
Disconnect the appliance from the power supply.
1.
Remove the filter system.
2.
Scoop out any water.
3.
1
Prise off the pump cover using a
4.
spoon and grip it by the crosspiece.
2
Lift the pump cover inwards at an angle and remove.
5.
Remove any remnants of food and foreign bodies in the area
6.
of the impeller.
Insert the pump cover
7.
down ⁠ .
a The pump cover clicks into position.
Install the filter system.
8.
Fault Cause and troubleshooting
Remnants of food on Washing programme selected too weak.
tableware.
Select a more intensive washing programme.
▶
Removable streaks are Amount of rinse aid to be dispensed is set too high.
present on glasses, glass- Set the rinse aid system to a lower setting.
▶
ware with a metallic ap-
No rinse aid has been added.
pearance and cutlery.
Add rinse aid.
▶
Rust spots on cutlery. Cutlery is not sufficiently rust-resistant. Knife blades are often
more severely affected.
Use rust-resistant tableware.
▶
Cutlery may also rust if washed together with rusting items.
▶ Do not wash rusting items.
Detergent residue is Spray arms were blocked by tableware so detergent was not
present in the detergent rinsed out.
dispenser or the tablet
Check that the spray arms are not blocked and can rotate
▶
collecting tray.
freely.
All LEDs light up or flash Electronics have detected a fault.
or the rinse programme
▶ Press the main switch button for approx. 4 seconds.
does not continue run-
The appliance is reset and restarted.
ning.
and press
2
1