Hummer XB70 - Bluetooth Party Speaker Manual

SPECIFICATION

RMS Power: 40W (Peak Power: 400W)
Frequency Response: 60Hz – 20KHz
Signal to noise: >60 dB
Bluetooth version: Bluetooth V5
Bluetooth Frequency: 2402-2480MHz
Bluetooth range: Up to 10m
Transmission power <4dBm
Input: DC 5V 2A
Battery: 11.1V 2000 mAh
Battery working hour: up to 13 hours @50% Volume (LED OFF)
Charging time: up to 5 hours
The main unit Meas: H220 x W175 x D 175 (mm)
The main unit Weight: 2.2kg

UNPACKING

Check that all the following items should be included in the box.

• Main Unit
• USB charging cable
• User Manual

Functions

1. Power Button
2. Volume+ / NextTrack
3. Volume– / Previous Track
4. Pairing Button
5. Light Mode Button
6. Party Mode Button
7. Lighting / Strobe Button
8. Color Button
9. 360 Sound Button
10. Micro USB Charging Port
11. Aux-inPort

Getting started

Charging the battery:

Give the speaker a full charge before its first use:

1. Connect the supplied Micro USB charging cable to the Micro USB charging port (10) and plug into power
2. The Power button (1) will be solid red whilst charging which will take up to 5 hours
3. Once fully charged the Power button (1) will turn white

Note:

• Allow up to 5 hours for the first charge. Youcan play your speaker whilst it is being charged, but this will affect the charging time.
• Dueto the large battery we recommend regularly charging the battery whenever practical. This will also help to ensure the longevity of the battery's life.
• When the battery is in power saving mode, the XB70 volume will be limited to 50%. Please recharge the battery further if you wish to increase the volume.

Quick Start

1. Power On by pressing Power button for 2 seconds.
2. Turn on your device's Bluetooth and connect to'XB70'.
3. Use the buttons on the handle control panel to adjust lighting, add strobes and change up the audio modes.
   

LED lights indication

Pairing the XB70 to your device

1. Press Power button (1) for 2 seconds to turn the speaker on and it will automatically enter pairing mode
2. Turn your Bluetooth device's Bluetooth ON and search for new devices
3. Select 'XB70'. If asked for a passcode, enter '0000', and the device will pair
4. Once connected the Pairing button (4) will turn white.

Re-pairing or pairing new devices

1. Turn Bluetooth connectivity off on any previously paired devices
   OR
2. Press the Pairing button (4) to re-enter pairing mode
3. Follow the 'Pairing the XB70 to your device' instructions

Note: If a previously paired device is not present within the Bluetooth connectivity range then the speaker will re-enter pairing mode.

TWS pairing two XB70 speakers

1. Press Power button (1) to turn on both of the speakers that you wish to pair together. Both speakers will automatically enter pairing mode.
2. Doublepress the Pairing Button (4) on either of the speakers and it will enter TWS pairing. The pairing button (4) will flash red on the master speaker.
3. Once connected in TWS pairing both speakers will commence party lighting in sync.
4. Follow the 'Pairing the XB70 to your device' instructions to pair your device to either XB70.
5. Once connected the Pairing button (4) will turn white.

Disconnecting two XB70 speakers from TWS

Double press the pairing button (4) on either of the paired speakers to disconnect them from TWS pairing.

Playing music on your speaker

Bluetooth

When connected via Bluetooth, play music on your device and the sound will play through the speaker. Some devices may require you to select the audio output.

Auxiliary

Plug the Aux cable (not included) into the speaker's Aux-in Port (11) and your device.

Auxiliary and TWS pairing

1. Ensure both speakers are paired before you connect the aux cable to the master speaker. Follow instructions for 'TWS pairing two XB70 speakers'.
2. Connect the aux cable to the master speaker. The Master speaker can be identified as the speaker with the Pairing button (4) flashing red.
3. Once connected, pairing button (4) will now be white on both speakers.

Once connected to the XB70 either wired or by Bluetooth, please follow the instructions:

*Strobe lighting is only available in Party Mode.
** If you perform a factory reset we recommend turning the speaker off and back on again, otherwise you may experience difficulties with TWS pairing.

Light mode controls

The XB70 has four different light modes. These include Light mode 1, 2 and 3, as well as Party mode. Within Party modethere is the additional option to add strobe lighting.

*Strobe lighting is only available in Party Mode.

Light brightness controls

The brightness of the lighting can be adjusted using the lighting button.

1. Hold down the lighting button (7) and short press Volume + (2) to increase brightness
2. Hold down the lighting button (7) and short press Volume – (3) to decrease brightness.

Using the brightness controls above will allow you to adjust the light brightness manually.

Light Synchronization Reset

If strobe lighting appears to be unsynchronized then we recommend that you exit Party mode by pressing the Light mode button (5) and then re-entering Party Mode by pressing Party mode button (6).

Sound Modes

XB70 offers three different sound modes. These include Indoor 360, Outdoor 360 and Shelf. Use the 360 Sound button (9) to toggle between the three differentmodes.

Battery Protection Mode

We recommend using a 2.1 amp charger adaptor or power bank for charging your XB70.

Please note:

• Your XB70 will enter Battery Protection Mode when the battery is low in order to prolong the playtime.
• Charge the XB70 before or as soon as it enters Battery Protection Mode in order to prolong the battery lifeand to ensure that it is always chargeable.
• The volume in Battery Protection Mode will be limited to 50%.
• If your XB70 is out of battery it will take up to 1 hour and 20 minutes to charge up and exit Battery Protection Mode if you are playingmusic at high volume
• It's suggested you decrease the volume not higher than 70% first during charging at Battery Protect Mode.
• Your XB70 will not fully charge if you are playing music at high volume and the lights are on.

STANDBY In power on mode in below condition for 30 minutes, unit will turn into standby mode automatically for power saving.
Bluetooth mode: No connection/no playback
Aux mode: No playback/mute/the input device volume is very low