Summary of Contents for ACR Electronics RCL-50 LED
- Page 1 PRODUCT SUPPORT MANUAL RCL-50 LED// Remote Control LED Searchlight System Model No.: RCL-50 LED Product No.: 1960, 1961 Y1-03-0349 Rev. A...
- Page 2 CAUTION: Before proceeding to install, test or use your new ACR Electronics product, please read this Product Support Manual in its entirety.
-
Page 3: Table Of Contents
Table of Contents SECTION 1- FOREWORD _____________________________________ 3 SECTION 2- GENERAL ________________________________________ 4 SECTION 3- SEARCHLIGHT ____________________________________ 4 SECTION 4- REMOTE CONTROL SYSTEM _________________________ 5 SECTION 5- URP-102 POINT PAD™ _____________________________ 5 SECTION 6- URC-103 Master Controller _________________________ 9 APPENDIX A- SPECIFICATIONS APPENDIX B- PRODUCT COMPONENTS ________________________ 14 APPENDIX C- ACCESSORY COMPONENTS_______________________ 15 PLEASE READ ALL WARNINGS, CAUTIONS AND... -
Page 4: Section 1- Foreword
SECTION 1 - FOREWORD Congratulations and thank you for purchasing the ACR RCL-50 LED Searchlight. The RCL-50 LED has been tested extensively to ensure it can survive the harshest environmental conditions. This assures that the products we offer stand up to the tough marine environment. With proper care and maintenance your searchlight will be in service for years to come. -
Page 5: Section 2- General
SECTION 2 - GENERAL The RCL-50 LED was specially designed for mariners who require a high intensity remote controlled searchlight that can stand up to the tough marine environment. The RCL-50 LED 12/24V searchlight system contains a narrow beam searchlight that produces approximately 100,000 peak candle power using a power efficient LED module. -
Page 6: Section 4- Remote Control System
After the coax cable has been routed and the “F” connectors attached to the coax cable, simply screw the “F” connectors to the Master Controller and the Point Pad™. The cable and connectors are available either through ACR Electronics or other sources of electronic hardware. - Page 7 Additional Point Pads™ (up to three (3) pads) may be used with one (1) Master Controller. A standard "T" connector or RG-59 television type "splitter" is used for each additional Point Pad (see Figure 2). Limit the total length of all coax cable used to 300 feet.
- Page 8 Figure 3- URP-102 Point Pad™ Functions URP-102 Point Pad Functions • Press the ON/OFF button to turn the lights ON or OFF. • Press the SPEED button to toggle between High and Low rotation speeds. • Press the Right or Left Arrows to rotate the Searchlight in that direction. •...
- Page 9 Figure 4- URP-102 Point Pad™ Surface Mount Case Figure 5- URP-102 Point Pad™ Flush Mount Case...
-
Page 10: Section 6- Urc-103 Master Controller
General wiring scheme The RCL-50 LED has a unique wiring scheme. Special attention must be paid to the following chart. The Master Controller is supplied with an in-line fuse-holder on the orange power lead. Use only 5 amp fuses in this fuse-holder. See Figure 7 for the master controller wiring diagram. - Page 11 Master Controller's in-line fuse-holder. Wiring to Searchlight The RCL-50 LED searchlight is supplied with a 15 foot integral wire harness. If you must lengthen the wire harness, use the same gauge wire to minimize the voltage drop. This is especially important for the ORANGE lamp power (+) and BLUE lamp ground (-) wires.
- Page 12 The URC-103 Master Controller has the unique XRCiZ™ feature. The XRCiZ™ feature routinely operates all moving parts in the searchlight to keep the motors and drive mechanism freely running. Once activated, and every 30 days thereafter, the XRCiZ™ feature wakes up and operates the searchlight. The searchlight will rotate 360...
- Page 13 (Note: Wiring must be Figure 7- URC-103 Master Controller Wiring Diagram in accordance with this diagram, improper wiring will damage components)
- Page 14 Figure 8 - URC-103 Master Controller...
-
Page 15: Appendix B- Product Components
APPENDIX A- RCL-50 LED SPECIFICATIONS (with URC-103 Controller) Specification 12V or 24V Unit Mirror diameter 4in (10.16cm) DC12V – DC24V Input voltage (Volt) 2.6A (12V) Input current (A) 1.3A (24V) Applicable lamp LED (LSM20) Peak beam candle power >100,000 (candela) Beam spread (degrees) Approximately 10°... -
Page 16: Appendix C- Accessory Components
Nuts, Nylon-lock A1-05-0776 Washers A1-05-0777 Warranty Card A1-20-1166 Product Support Manual Y1-03-0349 Mounting Templates Y1-03-0138-1 APPENDIX C- ACCESSORY COMPONENTS Product No. 1949 - URC-103 Master Controller Installation Kit includes: Description Quantity ACR Part Number Master Controller, URC-103 A3-06-2231-2 Connector, "In-Line" A1-03-0222 Instruction Sheet, Master Controller Y1-06-0314... - Page 17 Product No. 9282.3 – URP-102 Point Pad™ Secondary Station Installation Kit includes: Description Quantity ACR Part Number Point Pad™, URP-102 with Surface A3-06-2230 Mount case Case, Flush Mount A1-18-1875-2 Gasket, Surface Mount A1-25-0140-1 Gasket, Flush Mount A1-25-0140-2 U Clamp A1-17-1366 Nuts, Nylon-lock A1-05-0776 Washers...
- Page 18 ACR cannot accept liability for manual contents. ©2009 by ACR Electronics, Inc. All rights reserved. Reproduction in whole or in part permitted only...
- Page 19 EC DECLARATION OF CONFORMITY ACR Electronics, Inc. hereby declares under its sole responsibility that the following product is in conformity with Directive 2014/30/EU of the European Parliament and of the Council of 26 February 2014 on Electromagnetic Compatibility (EMC Directive).