Epson UB-U01III User Manual

Standards and Approvals
The following standards are applied only to the interface boards that are so labeled. (EMC is tested using the Epson
power supplies and TM series printers.)
Les normes suivantes ne s'appliquent qu'aux cartes d'interface ainsi étiquetées. (CEM est testé à l'aide des blocs
d'alimentation Epson et des imprimantes de la série TM.)
Europe: CE marking
North America/Amérique du Nord: FCC Class A, ICES-003 Class A
Oceania: Radiocommunications (Electromagnetic Compatibility) Standard , Class A
WARNING
This is a Class A product. In a domestic environment this
product may cause radio interference, in which case the
user may be required to take adequate measures.
The printers in which this board is installed becomes
class A devices.
The connection of a non-shielded printer interface cable
to this board will invalidate the EMC standards of this
device.
You are cautioned that changes or modifications not
expressly approved by Seiko Epson Corporation could
void your authority to operate the equipment.
English
Before Using
Be sure to read this manual carefully for effective and correct use of the product and store it in accessible location.
Key to Symbol
The symbol in this manual is defined below. Read the following carefully before handling the product.
CAUTION:
Observe cautions to avoid minor injury to yourself or damage to your equipment.
Precaution
To avoid contamination, do not touch the board connector.
Introduction
The UB-U01III/U02III/U03II, designed for Epson TM printers, is a USB interface board.
O When you install the UB-U01III/U02III, you cannot use a display module connector (DM connector) on the printer.
Use the DM connector on the UB-U01III/U02III.
O The UB-U01III uses a bus-powered hub. Note that it cannot be directly connected to other bus-powered hubs
(including the UB-U01III) or bus-powered functions that consume current over 100 mA. (The UB-U02III and UB-
U03II can be directly connected to the hub on the UB-U01III.)
Operation Environments when Using USB Port
Operation Environments
Hardware: USB compliant PC
OS: Windows 98 or later (Second Edition is recommended)
For detailed information on other operating systems, please ask your dealer.
Software: You need a device driver when you use the product.
Please ask your dealer how to get the device driver for the UB-U01III/U02III/U03II and how to install it.
Note:
Even if the above operation environments are satisfied, your system may not work properly, depending on the devices
connected to your system.
Unpacking
Make sure you have these items. If any item is missing or damaged, please contact your dealer for assistance. If
necessary, you can get a locking wire strain relief separately through your dealer by using the part numbers listed
below in brackets.
O UB-U01III/U02III/U03II
O Manuals
O Ferrite core [2031678]
O Locking wire strain relief
• For UB-U01III/U02III [1061268]
• For UB-U03II [1091047]
Connecting the Interface Cable
USB Interface Cable Connection
1. Make sure both the printer and the host computer are turned off.
2. Hook the USB cables through the locking wire strain relief to keep it in place.
©Seiko Epson Corporation 2003–2023
UB-U01III/U02III/U03II
User's Manual / Manuel d'utilisation / ユーザーズマニュアル
https://support.epson.net/p_doc/924/
AVERTISSEMENT
Cet appareil est un produit de classe A. Dans un
environnement résidentiel, il risque de provoquer un
brouillage radio, auquel cas l'utilisateur pourra être tenu
de prendre des mesures adéquates.
Les imprimantes dans lesquelles cette carte est installée
deviennent des appareils de classe A.
La connexion d'un câble d'interface d'imprimante non
blindé à cette carte invalidera les normes CEM de cet
appareil.
Vous êtes averti que les changements ou modifications
non expressément approuvés par Seiko Epson
Corporation peuvent invalider votre droit à faire
fonctionner l'équipement.
English Français Español
日本語
Română Українська
CE Marking
U https://www.epson.eu/conformity
FCC Compliance Statement for Users in the USA
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at his own expense.
For Users in Canada
This Class A digital apparatus complies with Canadian ICES-003.
Pour les utilisateurs au Canada
Cet appareil numérique de classe A est conforme à la norme canadienne NMB-003.
USB upstream connector
USB downstream connector
(USB HUB: UB-U01III only)
3. Insert the square connector end of the USB cable into the upstream connector of the UB-Board.
4. Insert the opposite end of the USB cable into the downstream connector of the host computer.
5. Change the printer settings to the parallel interface settings. If you use a printer that permits selecting the setting of
the I/F pin 31 reset signal, select "Enabled. " For details, see the settings described in the printer documentation.
6. Install the device driver for the TM-U01III/U02III/U03II. For installation procedures, please ask your dealer.
Display Module
If you install a display module, be sure to use the following settings.
Transmission setting
Default setting of Device selection
(only for displays for which the setting can be changed)
Connection type
(only for displays for which the setting can be changed)
See the manual for more details of the display module setting. Also, you should note the following points before
installing.
CAUTION:
Do not connect any device other than the Epson display module connector to the DM connector. Also, do not connect
other lines, such as a telephone line, to the DM connector; otherwise the printer and other lines may be damaged.
Be sure to mount the ferrite core on the display module cable to satisfy the EMI standard.
To mount the ferrite core, put the display module cable into the ferrite core, as shown in the illustration below.
display module
Türkçe
Item
Baud rate
Parity
Data word length
Only display selected
Y connection disabled
ferrite core
DM connector
Locking wire
strain relief
USB cable
Selection
19200 bps
None
8 bit
Printed in XXXXXX
Imprimé XXXXXX
Impresso XXXXXX
Impreso en XXXXXX